• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.6
• /
• pp.120-125
• /
• 2004

There are very few numbers of 115K FPP (Fixed Pitch Propulsion) Tankers for the Baltic ice class IA because the minimum power requirement of FMA (Finish- Swedish Maritime Association) needs quite large engine power and the 40 m Beam is out of calculation range of FMA minimum power requirements. The shipyard has no choice except to increase the engine power to satisfy FMA minimum power requirement Rule. And the operation cost, efficiency of hullform and its building cost are not good from the ship owners' point of view To solve this problem, the experience of ice breaking tanker development and the ice tank test results were adopted. The main idea to reduce the ice resistance is by reducing waterline angle at design load waterline. The reason behind the main idea is to reduce the ice-clearing force. Two hull forms were developed to satisfy Baltic Ice class IA. Two ice tank tests and one towing tank test was performed at MARC (Kvaener-Masa Arctic Research Center) and SSMB (Samsung Ship Model Basin) facilities, respectively. The purpose of these tests was to verify the performance in ice and open water respectively The hull form 2 shows less speed loss compared to Hull form 1 in open water operation but hull form 2 shows very good ice clearing ability. finally the Hull Form 2 satisfying Baltic ice class IA. The merit of this hull form is to use the same engine capacity and no major design changes in hull form and other related designs But the hull structure has to be changed according to the ice class grade. The difference in two hull form development methods, ice model test methods and analysis methods of ice model test will be described in this paper.

• Polymer(Korea)
• /
• v.25 no.3
• /
• pp.359-366
• /
• 2001

Isothermal physical aging of a glass fiber/epoxy composite was examined at different aging temperatures ($T_a$) and degrees of conversion (monitored by the glass transition temperature, $T_g$) by means of the TBA torsion pendulum technique. The range of aging temperature was from 10 to $130^{\circ}C$ : the conversion was systematically changed from $T_g$=$76^{\circ}C$ to $T_g$=$177^{\circ}C$ (fully crosslinked). The effect of isothermal physical aging was manifested as perturbations of the modulus and mechanical loss vs. temperature in the vicinity of $T_a$ for all conversions. The rate of isothermal physical aging determined from the change of modulus with aging time at fixed aging temperature decreased and then increased with increasing conversion below T$_{a}$=9$0^{\circ}C$. There exists a superposition in aging rate vs. ($T_g$ -$T_a$) by shifting horizontally and vertically. This implies that the physical aging process is independent of the change of chemical structure as conversion proceeds. It has been found that water absorbed at the aging temperature below $70^{\circ}C$ during isothermal physical aging lowers the apparent aging rate. It is due to the absorbed water molecules forming strong polar interactions with hydroxyl group on network chain and reducing the segmental mobility during the physical aging.g.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.260-265
• /
• 2002

Microbiologically influenced Corrosion (MIC) is one of the most deleterious effects of metal microbe interactions. When a fresh metal surface comes in contact with a non-sterile fluid, biofilm formation is ensued. This might result in the initiation of corrosion. The sites and materials where MIC is implicated are versatile. Industries such as shipping, power generation, chemical etc are reported to be affected. The rapid and unexpected failure of AISI type 304 stainless steel was investigated in the laboratory by simulation studies for a period of 4 months. Slime and water samples from the failure site were screened for corrosion causing bacteria. Both aerobic and anaerobic nora were enumerated and identified using PCR techniques. Pseudomonas sp. and Bacillus sp. were the most common aerobic bacteria isolated from the water and slime samples, whilst sulfate reducing bacteria (SRB) were the major anaerobic bacteria. The aerobic bacteria were used for the corrosion experiments in the laboratory. Coupon exposure studies were conducted using a very dilute (0.1%V/V) nutrient broth medium. The coupons after retrieval were observed under a Scanning Electron Microscope (SEM) for the presence of MIC pits. Compared to sterile controls, metal coupons exposed to Pseudomonas sp and Bacillus sp. showed the initiation of severe pitting corrosion. However, amongst these two strains, Psudomonas sp. caused pits in a very short span of 14 days. Towards the end of the experiment, severe pitting was observed in both the cases. The detailed observation of pits showed they vary both in number and shapes. Whilst the coupons exposed to Bacillus sp. showed widely spread scales like pits, those exposed to Pseudomonas sp. showed smaller and circular pits, which had grown in number and size by the end of the experiment. From these results it is inferred that the rapid and unexpected failure of 304 SS might be due to MIC. Pseudonwnas sp. could be considered as the major responsible bacteria that could initiate pits in the metallic structures. As the appearance of pits was different in both the tested strains, it was thought that the mechanisms of pit formation are different. Experiments on these lines are being continued.

• Food Science and Preservation
• /
• v.19 no.1
• /
• pp.138-143
• /
• 2012

The anti-obesity activity of the $Cucubita$ $moschata$ Duch. extracts was investigated. The inhibitory effect on triglyceride accumulation was shown in 3T3-L1 preadipocyte. The lipid accumulation of the ethanol extract in 5 mg/mL concentration was shown to be 75.4%, where as that of water extract was shown to be 85.2%. The survival rate of the cell in the viability test was shown to be 86.5% in the 0.5-5 mg/mL concentration. Total polyphenol content was highest in the water extract($46.54{\pm}0.02$ mg). These results suggest that $Cucubita$ $moschata$ Duch. extracts have a potential as anti-obesity material by reducing the lipid accumulation.

• Journal of Hydrogen and New Energy
• /
• v.19 no.1
• /
• pp.18-25
• /
• 2008

The membrane electrode assembly(MEA) was prepared by a nonequilibrium impregnation- reduction (I-R) method. Nafion 117 and covalently cross-linked sulfonated polyetherether with tungsto- phosphoric acid (CL-SPEEK/TPA30) prepared by our laboratory, were chosen as polymer electrolyte membrane(PEM). $Pt(NH_3)_4Cl_2$, $RuCl_3$ and reducing agent $(NaBH_4)$ were used as electrocatalytic materials. Electrochemical activity surface area(ESA) and specific surface area(SSA) of Pt cathodic electrode with Nafion 117 were $22.48m^2/g$ and $23.50m^2/g$ respectively under the condition of 0.8 M $NaBH_4$. But Pt electrode prepared by CL-SPEEK/TPA30 membrane exhibited higher ESA $23.46m^2/g$ than that of Nafion 117. In case of Pt-Ru anodic electrode, the higher concentration of Ru was, the lower potential of oxygen reduction and region of hydrogen desorption was, and Pt-Ru electrode using 10 mM $RuCl_3$ showed best properties of SSA $34.09m^2/g$ with Nafion 117. In water electrolysis performance, the cell voltage of Pt/PEM/Pt-Ru MEA with Nafion 117 showed cell property of 1.75 V at $1A/cm^2$ and $80{\circ}C$. On the same condition, the cell voltage with CL-SPEEK/TPA30 was the best of 1.73 V at $1A/cm^2$.

• Journal of Environmental Science International
• /
• v.24 no.7
• /
• pp.917-925
• /
• 2015

Styela clava tunic is generated in large amounts as a waste from S. clava processing plants and leads to environmental problems. It destroys the beach scenery and causes a bad smell and pollution by trashing on the seashore. Therefore, purpose of this study was to investigate antioxidant and antihypertensive activities of different solvent extracts from S. clava tunic for recycling of fishery waste. Antioxidant and antihypertensive activities of all extracts were concentration-dependent. Of extracts, hot water extract showed the highest DPPH radical scavenging activity with the lowest effective concentration ($EC_{50}$) value (0.733 mg/ml). Chloroform extract exhibited the highest metal chelation activity with the lowest $EC_{50}$ value (2.696 mg/ml). Autoclaved water extract showed the highest NO radical scavenging activity with the lowest $EC_{50}$ value (0.491 mg/ml) and n-hexane extract showed the highest reducing power ($A_{700}=1.897$ at 100 mg/ml). And n-butanol extract showed the highest SOD-like activity with the lowest $EC_{50}$ value (19.116 mg/ml) and ACE inhibition activity with the lowest inhibitory concentration($IC_{50}$) value (0.149 mg/ml). These results indicate that extracts obtained from S. clava tunic may potential candidate to reduce diseases caused by various oxidative stresses and hypertension.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.46 no.1
• /
• pp.1-9
• /
• 2017

Acer tegmentosum Maxim (ATM) is known as traditional medicine for treatment of hepatic disorders such as hepatitis, related-inflammatory disease, and hepatic cancer. In this study, we evaluated the antioxidant and anti-inflammatory effects of ATM extracted with $80^{\circ}C$ water or 95% ethanol. Antioxidant activities of ATM extracts were measured based on DPPH and ABTS radical scavenging activities, total polyphenolic compound contents, and ferric reducing antioxidant power. The anti-inflammatory effects of ATM extract were assayed on release of nitric oxide, tumor necrosis factor $(TNF)-{\alpha}$, and interferon $(IFN)-{\gamma}$ from lipopolysaccharide (LPS)-induced macrophages. In these experiments, 95% ethanol extract of ATM showed stronger antioxidant and anti-inflammatory effects than water extract. Therefore, we determined the effects of ATM ethanol extract on an animal model of sepsis. Seven days oral gavage of ATM ethanol extract followed by LPS stimulation reduced the protein levels of $TNF-{\alpha}$ and $IFN-{\gamma}$ in serum as well as mRNA levels of $TNF-{\alpha}$ and interleukin-6 in intestinal epithelial cells. In addition, ATM ethanol extract reduced DNA damage in mouse lymphocytes. These results indicate that ATM extract has strong antioxidant and anti-inflammatory in vitro and in vivo effects and may be developed as a potential food material for prevention of inflammatory diseases.

• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.317-328
• /
• 2016

This research intends to understand the impact of super-absorbent polymer (SAP) as an internal curing agent in Ultra-High Performance Concrete (UHPC). Two different types of SAPs of acrylic acid (SAP_AA) and acrylic acid-co-acrylamide (SAP_AM) were examined with UHPC formulation. Isothermal calorimetry and x-ray diffraction experiments revealed the impact of polymers with the different chemical bonds on cement hydration. To test its feasibility as a shrinkage reducing admixture for UHPC, a series of experiments including flowability, compressive strength, rapid chloride permeability and autogenous shrinkage profile was performed. While both SAPs showed a reduction in autogenous shrinkage, it has been concluded that the SAP size and chemical form significantly affect the performance as an internal curing agent in UHPC by controlling cement hydration and porosity modification. Between the tested SAPs, SAP_AM which absorbs more water in UHPC than SAP_AA, shows better mechanical and durability performance.

• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.347-354
• /
• 2013

Recently, crushed fine aggregates are being widely used due to the shortage of natural sand. In Korea, the amount of fine particles under 0.08 mm contained in crushed fine aggregates is restricted to be less than 7%, which is similar to the regulations of ASTM but is still very strict compared to the regulations of the other nations. In addition, the crushed aggregates already have in them about 20% of fine particles under 0.08 mm which occurs while they are crushed. The fine particles are not easy to wash out, and also to maximize the use of resources it is deemed necessary to review the possibility of enhancing the limit of the amount of fine particles. Therefore, this study conducted experiments to analyze the characteristics of fine particles under 0.08mm and their influence on the properties of concrete. Experiments using silt and cohesive soil were also done for comparison. In the experiments on fine particles, the methylene blue value was more in the soil dust contained in silt and cohesive soil than in the stone powder contained in crushed fine aggregates. Also, the methylene blue value had a close correlation with packing density and liquid & plastic limit. In the experiments done with concrete, the quantity of high range water reducing agent demanded to obtain the same slump increased as the fine particle substitution rate heightened. However, in the experiment which used stone powder testing the compressive strength and tensile strength of concrete in the same water-cement ratio, there was little change in strength with less than 20% addition of fine particles among the fine aggregates, and no meaningful difference in the amount of drying shrinkage of concrete.

• Journal of Environmental Science International
• /
• v.25 no.11
• /
• pp.1541-1554
• /
• 2016

To understand the characteristics of vanadium leaching from soils formed by the weathering of basalts, paleo soil at Gosan, Jeju Island, Korea, and several present-day soils from neighboring areas were collected. Leaching experiments were carried out by two approaches: 1) batch experiments under various geochemical conditions (redox potential (Eh) and pH) and 2) continuous leaching experiments under conditions similar to those of natural environments. From the batch experiments, leached vanadium concentrations were highest under alkaline (NaOH) conditions, with a maximum value of $2,870{\mu}g/L$, and were meaningful (maximum value, $114{\mu}g/L$) under oxidizing ($H_2O_2$) conditions, whereas concentrations under other conditions (acidic-HCl, $neutral-NaHCO_3$, and $reducing-Na_2S_2O_3$) were negligible. This indicated that the geochemical conditions, in which soil-water reactions occurred to form groundwater with high vanadium concentrations, were under alkaline-oxidizing conditions. From the continuous leaching experiments, the pH and leached vanadium concentrations of the solution were in the ranges of 5.45~5.58 and $6{\sim}9{\mu}g/L$, respectively, under $CO_2$ supersaturation conditions for the first 15 days, whereas values under $O_2$ aeration conditions after the next 15 days increased to 8.48~8.62 and $9.7{\sim}12.2{\mu}g/L$, respectively. Vanadium concentrations from the latter continuous leaching experiments were similar to the average concentration of groundwater in Jeju Island ($11.2{\mu}g/L$). Furthermore leached vanadium concentrations in continuous leaching experiments were highly correlated with pH and Al, Cr, Fe, Mn and Zn concentrations. The results of this study showed that 1) alkaline-oxidizing conditions of water-rock (soil) interactions were essential to form vanadium-rich groundwater and 2) volcanic soils can be a potential source of vanadium in Jeju Island groundwater.