• Journal of the Korean Solar Energy Society
• /
• v.31 no.3
• /
• pp.23-28
• /
• 2011

In this study, the ejector design was modeled using Fluent 6.3 of FVM(Finite Volume Method) CFD(Computational Fluid Dynamics) techniques to resolve the flow dynamics in the ejector. A vacuum system with the ejector has been widely used because of its simple construction and easy maintenance. Ejector is the main part of the desalination system, of which designs determine the efficiency of system. The effects of the ejector was investigated geometry and the operating conditions in the hydraulic characteristics. The ejector consists mainly of a nozzle, suction chamber, mixing tube (throat), diffuser and draft tube. Liquid is supplied to the ejector nozzle, the fast liquid jet produced by the nozzle entrains and the non condensable gas was sucked into the mixing tube. The multiphase CFD modeling was carried out to determine the hydrodynamic characteristics of seawater-air ejector. Condition of the simulation was varied in entrance mass flow rate (1kg/s, 1.5kg/s, 2kg/s, 2.5kg/s, 3kg/s), and position of driving nozzle was located from the central axis of the suction at -10mm, 0mm, 10mm, 20mm, 30mm.. Asaresult, suction flow velocity has the highest value in central axis of the suction.

• Nuclear Engineering and Technology
• /
• v.32 no.4
• /
• pp.395-409
• /
• 2000

Parametric studies were performed to assess the sensitivity in determining the maximum in-vessel heat removal capability from the core material relocated into the lower plenum of the reactor pressure vessel (RPV）during a core melt accident. A fraction of the sensible heat can be removed during the molten jet delivery from the core to the lower plenum, while the remaining sensible heat and the decay heat can be transported by rather complex mechanisms of the counter-current flow limitation (CCFL) and the critical heat flux (CHF）through the irregular, hemispherical gap that may be formed between the freezing oxidic debris and the overheated metallic RPV wall. It is shown that under the pressurized condition of 10MPa with the sensible heat loss being 50% for the reactors considered in this study, i.e. TMI-2, KORI-2 like, YGN-3&4 like and KNGR like reactors, the heat removal through the gap cooling mechanism was capable of ensuring the RPV integrity as much as 30% to 40% of the total core mass was relocated to the lower plenum. The sensitivity analysis indicated that the cooling rate of debris coupled with the sensible heat loss was a significant factor The newly proposed heat removal capability map (HRCM) clearly displays the critical factors in estimating the maximum heat removal from the debris in the lower plenum. This map can be used as a first-principle engineering tool to assess the RPV thermal integrity during a core melt accident. The predictive model also provided ith a reasonable explanation for the non-failure of the test vessel in the LAVA experiments performed at the Korea Atomic Energy Research Institute (KAERI), which apparently indicated a cooling effect of water ingression through the debris-to-vessel gap and the intra-debris pores and crevices.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.84-92
• /
• 2010

현재 가동 중인 몇몇 가압 경수로 원전 안전 1등급 설비의 이종금속 용접부는 일차수응력부식균열(PWSCC : Primary Stress Corrosion Cracking) 발생의 세가지 조건(민감 재질, 부식 환경, 인장응력)을 동시에 충족하고 있다. 즉, 이종금속 용접부는 PWSCC에 민감한 재질인 Alloy 600 계열 합금으로 제작 또는 용접되어 있으며 고온 수화학 부식 환경 하에 놓여있다. 아울러 오스테나이트 스테인리스 강의 예민화 예방을 위한 용접 후열처리 미실시로 높은 인장 용접 잔류응력이 작용하고 있다. 이러한 이종금속 용접부의 특성상 PWSCC가 발생할 잠재성이 있을 뿐만 아니라 국내외적으로 Alloy 600 계열 합금으로 제작 및 용접된 가압 경수로 원전 안전 1등급 설비의 이종금속 용접부에 실제 PWSCC가 발생된 사례들이 다수 보고되고 있다. 운전 환경 및 재질 변화 없이 PWSCC 발생을 예방하기 위해서는 인장 잔류응력을 이완시켜 낮은 인장 또는 압축 응력화하여야 한다. 이러한 인장 잔류응력 이완방법들로는 PWOL(Pre-emptive Weld Overlay), 레이저 피닝(Laser Peening), MSIP(Mechanical Stress Improvement Process), 워터 제트 피닝(Water Jet Peening), IHSI(Induction Heating Stress Improvement) 방법들이 있는데 공정 시간이 짧고 열 에너지 원이 필요 없으며 전체적인 소성 변형을 야기시키지 않는 레이저 피닝을 본 연구의 대상 방법으로 한다. 본 연구에서는 동적 유한요소 해석을 통해 용접 잔류응력을 이완시키는 레이저 피닝의 효과를 검증하고 용접 잔류응력에 미치는 레이저 피닝 변수의 영향을 고찰하고자 한다. 내부 보수용접이 수행된 경수로 원전 가압기 노즐 이종금속 용접부에 레이저 피닝을 적용한 경우에 대해 상용 유한요소 해석 프로그램인 ABAQUS를 이용하여 동적 유한요소해석을 수행한 결과, 고온 수화학 일차수와 접하는 Alloy 600 계열 합금 내면에서의 인장 잔류응력이 상당히 이완됨을 확인하였다. 또한, 최대충격 압력이 증가할수록, 충격압력 지속시간이 증가할수록, 레이저 스팟 직경이 증가할수록 내표면 인장 잔류응력 이완 정도는 감소하나 이완되는 영역의 깊이는 증가함을 알 수 있다. 또한, 레이저 피닝 방향이 잔류응력 이완에 미치는 영향은 미미함을 알 수 있다.

• The Journal of the Korean dental association
• /
• v.54 no.12
• /
• pp.1035-1044
• /
• 2016

Purpose : The purpose of this study was to compare the plaque removal effects of vacuum oral cleaner developed for the patients with limited mobility with those of manual toothbrushes and high pressure injection oral cleaner (dental water jet). Meterials and methods : Thirty human subjects were measured with Patient Hygiene Performance index (PHP index) and O'Leary index before and after the use of toothbrush, high pressure injection oral cleaner and vacuum oral cleaner. These three different oral hygiene methods were conducted with seven-day intermittence. Then the statistical analysis was carried out to define plaque removal rate of three different oral hygiene methods (${\alpha}=.05$). Results : According to the efficacy analysis of plaque removal before and after the oral cleaning using each of three methods, significant reduction in plaque after the treatment compared to the previous state when using toothbrush, high pressure injection oral cleaner, and vacuum oral cleaner was observed (P < 0.001). PHP index of tooth brushing was higher than that of the high pressure injection oral cleaner, while PHP index of vacuum oral cleaner did not show significant difference from either of the other two methods. There was no significance difference in O'Leary index among the three methods. Conclusion : Effect of plaque removal using the vacuum oral cleaner is comparable to that of manual tooth brush or high pressure injection oral cleaner, so it will be helpful for self-oral hygiene care of the patients with limited mobility.

• Particle and aerosol research
• /
• v.5 no.2
• /
• pp.37-43
• /
• 2009

Particulate matter (PM) is one of the major indoor air pollutants especially in the subway station in Korea. In order to remove PM in the subway station, several kinds of PM removal system such as roll-filter, auto-washable air filter, demister, and electrostatic precipitator are used in the air handling unit (AHU) of subway stations. However, those systems are prone to operation and maintenance problems since the filter-regeneration unit consisting of electrical or water jet parts might malfunction due to the high load of particulates unless the filter medium is periodically replaced. In this study, the use of axial-flow cyclone was proposed for particulate filter unit in the AHU for its low operation and maintenance cost. Novel shape of axial-flow cyclone was designed by using computational fluid dynamics (CFD). The shape of vortex vane was optimized in terms of pressure drop and tangential velocity. In addition, CFD analysis was validated experimentally through the pressure drop measurement of mock-up model. We found that pressure drop and tangential velocity of fluid through the axia-flow cyclone was significantly affected by the rotating degree of vortex vane and the numerical prediction of pressure drop agreed well with experimental measurement.

• Korean Journal of Materials Research
• /
• v.21 no.8
• /
• pp.444-449
• /
• 2011

Nano-sized $Y_2O_3$ powders were prepared via a sol-gel method starting with $Y(NO_3)_3{\cdot}6H_2O$ (Yttrium(III) nitrate hexahydrate) and water with ethanol as a cosolvent. $Y_2O_3$ is an important rare earth oxide and has been considered for use in nuclear applications, such as ceramic materials, due to its excellent optical and refractory characteristics. It has been used as a chemically stable substrate, a crucible material for melting reactive metals, and a nozzle material for jet casting molten rare earth-iron magnetic alloys. Oxalic acid ($C_2H_2O_4$) has been adopted as a chelating agent in order to control the rate of hydrolysis and polycondensation, and ammonia was added in order to adjust the base condition. The synthesized $Y_2O_3$ powder was characterized using TG/DTA, XRD, FE-SEM, BET and Impedance Analyzer analyses. The powder changed its properties in accordance with the pH conditions of the catalyst. As the pH increases according to the FE-SEM, the grain grew and it showed that the pore size decreased while confirming the effect of the grain size. The nano-material $Y_2O_3$ powders demonstrated that the surface area was improved with the addition of oxalic acid with ammonium hydroxide.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.11
• /
• pp.971-975
• /
• 2013

In general, the solar photovoltaic power increases with higher solar insolation. However, the solar cell generation efficiency reduces because the solar cell surface is heated by solar insolation. According to advanced research, with a $1^{\circ}C$ increase in the solar cell surface temperature, the generation efficiency decreases by ~0.5%. To solve this problem, we conducted experiments in which we attempted to reduce the solar cell surface temperature using a water jet spray. In this study, we found the long-term experimental results of increases in solar power generation. The experimental results show a comparison of the site with and without cooling and cleaning equipment being installed. The results of the long-term experiments show that solar photovoltaic power generation is increased by at least 13% up to 19% with cooling and cleaning.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.519-519
• /
• 2013

본 연구에서는, 전기적 충격이 없고 넓은 면적을 동시에 처리할 수 있는 형태의 유전체 장벽 방전(DBD: Dielectric Barrier Discharge)을 이용한 대기압 저온 플라즈마 장치를 제작하고 이를 이용하여 빵 곰팡이(Neurospora crassa) 살균에 대한 기본 분석을 하였다. 실험에 사용한 저온 대기압 면방전 플라즈마의 파워는 사인파 교류전압을 인가하여, 방전전압은 1.4~2.3 kV, 방전전류는 20~30 mA의 값을 가지며, 전압과 전류의 위상차는 약 80도의 기울기 차이가 난다. 이때의 출력은 약 4 W를 가지며, 공랭식 쿨러를 이용하여 유전체의 열을 배출하였다. 시료대의 온도 측정결과 방전과 동시에 쿨러를 작동할 경우 최대 10분에서 37도를 넘지 않았다. 장치에서 발생하는 플라즈마에 의한 O3의 양은 플라즈마 발생부로부터 10 mm 이내에서 약 25~30 ppm 이 측정되었으며, NO나 NO2 는 거의 검지되지 않았다. 증류수(Deionized water)속에 담긴 빵 곰팡이(Neurospora crassa) 포자를 면방전 플라즈마 발생장치로 처리하였을 때, 포자의 발아율은 처리시간 및 출력파워가 증가함에 따라 급격히 감소하였으나 VM (Vogel's Minimal) 배양액에 넣고 플라즈마 처리를 한 경우에는, 증류수의 결과와 달리 살균효과가 미비함을 보였다. MTT 측정법 또한 같은 경향성을 보였으며, 이를 통해 포자를 둘러싸고 있는 환경이 플라즈마의 살균효과에 영향을 미치는 것으로 보인다. 본 실험을 통해, 유전체 장벽을 이용한 면방전 플라즈마 발생장치가 플라즈마 제트(jet)와 달리 직접적인 플라즈마 접촉 없이도 미생물 살균이 가능하다는 것을 보았으며, 처리대상의 생체용액과 같은 주변 환경에 영향을 받음을 알 수 있었다. 또한 면방전 플라즈마 장치로부터 발생하는 O3과 같은 활성종들이 빵 곰팡이의 비활성화에도 역할을 할 수 있음을 알 수 있었다.

• Research in Community and Public Health Nursing
• /
• v.13 no.3
• /
• pp.574-583
• /
• 2002

'채석(quarrying)'산업은 노천광산에서 광물을 캐내는 작업을 모두 포함하는 광범위한 산업을 의미한다. 1900년대에 들어오면서 채석작업에 홈연소기(channel burner)을 이용한 불꽃절개법(flame cutting)이 이용하여 근로자의 먼지 노출이 많이 감소하였다. 채석작업으로 인한 주 된 건강문제는 먼지, 소음, 진동 노출이며, 노천작업장으로 작업환경이 개방되어 있어 환경측정 및 관리가 불가능하므로 개별근로자의 먼지와 소음 노출 측정 및 예방이 중요하다. 본 연구는 미국의 일개 채석회사의 근로자 건강관리사업을 평가하였다. 연구자료는 저자가 현장 방문을 통하여 구한 자료와 연구대상 회사의 안전관리자의 의견 및 미국 산업안전보건국 전산자료를 이용하였다. 채석사업장에서 이루어지는 작업은 크게 채석작업과 실내에서 이루어지는 가공작업 및 운반과 보관이며, 미국 산업안전보건국(OSHA)의 표준산업분류(SIC)에서 1411(채석업)과 3281(채석가공업)에 해당한다<표 1>. 연구 대상 사업장에서 이루어지는 산업보건프로그램은 먼지 노출 예방을 위해 석재 채취시 물분사법(water jet quarrying)과 국소환기법을 사용하고 소음 노출 예방을 위해 귀마개를 사용하며 사고 예방을 위하여 안전모와 철모, 보안경, 안전조끼, 보호장갑, 안전끈(harness)을 착용하였다. 평가 결과로 나온 연구 대상 사업장에서 적용하여야 할 산업보건 프로그램은 첫째, 먼지 노출로 인한 건강문제를 예방하기 위하여 근로자 개별 노출 측정을 하고, 둘째 실내가공작업장의 근로자를 대상으로 한 먼지와 소음 노출 측정 및 환경측정이 필요하며, 셋째 안전관리를 위해 채석장에 안전표지판을 설치하여야 하며, 실내가공 작업장의 자동이동시스템을 작업별로 채색하여 식별을 용이하게 하여야 하겠다. 또한 이 연구 결과를 영세사업장의 산업간호프로그램인 'Clean 3D'사업에서 적용하여 우리나라 채석사업장 근로자 건강관리를 발전시켜야 하겠다.

• Composites Research
• /
• v.23 no.6
• /
• pp.61-66
• /
• 2010

In this paper, the variation of mechanical properties of T800 carbon/epoxy composites according to the forming pressure, which was referred to previous studies on a filament winding process, were investigated. The specimens of all the tests were fabricated by an autoclave de-gassing molding process controlling forming pressure (absolute pressures of 0.1MPa, 0.3MPa, 0.7MPa including vacuum) and water jet cutting after fabricating composite laminates. Various tensile tests were performed for in-plane properties and interlaminar properties were also measured by using Iosipescu test jig. Fiber volume fraction was measured to correlate the property variation and the forming pressure. This properties are expected to be utilized in the design of Type III pressure vessel for hydrogen vehicles which uses the same carbon fiber (T800 carbon fiber) for the filament winding process.