• 한국환경과학회지
• /
• 제8권5호
• /
• pp.601-605
• /
• 1999

This study has been performed to evaluate mineral water quality by using four parameters [Mg]/[Ca], [Na]/[K], [Mg]+[Ca]/[Na]+[K] and total hardness(as CaCO3 mg/ℓ). The four parameters has been ploted in a general scale and logarithmic scale, respectively. The method of general scale is not applicable for evaluation on several parameters. Therefore, the logarithmic scale is applied instead to settle the problem. The evaluation of the water quality is based on standard sample S, and the results of the 6 domestics and 5 overseas sample evaluation are as follow. At present, evaluation of the water quality on the mineral water can be done by using four parameters calculated from only cation concentration printed on the bottle's marking.

• Food Science and Biotechnology
• /
• 제15권3호
• /
• pp.409-412
• /
• 2006

Interrelationship between results of large deformation (texture profile analysis, TPA) test and small deformation (creep) test on ohmic heated surimi gel, water-bath heated surimi gel, and commercial fish gel products (kamabokos) was examined. Creep test revealed ohmic heated gels have higher elastic modulus and viscosity values than water-bath heated ones, with differences of elastic modulus and viscosity between ohmic and water-bath heated gels being 18 and 28.5%, respectively. These differences were reflected in the higher hardness, cohesiveness, and chewiness values of ohmic heated gels in TPA. In TPA test, the differences of hardness and chewiness between ohmic heated gel and water-bath heated gel were 29.3 and 38.7%, respectively. It was concluded that with proper experimental design, the small deformation creep test which gives molecular level deformation data can be related to the large deformation TPA test indicating the sensory textural properties.

• 공업화학
• /
• 제28권1호
• /
• pp.57-63
• /
• 2017

본 연구에서는 다양한 NCO index에서 물 함량 변화가 자동차용 폴리우레탄 시트 폼 패드의 정적 안락감에 미치는 영향을 알아보았다. 정적 안락감에 영향을 미치는 요인을 파악하기 위해 UTM을 사용한 정하중 특성 시험을 통하여 히스테리시스 곡선을 나타냈으며, 이를 통해 25% 변형 시 경도와 65% 변형 시 경도, hysteresis loop area, hysteresis loss (%), 그리고 Sag factor를 구하였다. 동일한 NCO index에서 물 함량이 증가함에 따라 우레아 결합의 증가로 경도가 증가하고, 가교밀도가 증가하는 경향을 swelling ratio 측정으로 확인하였으며, 이에 따라 복원력은 감소하는 경향을 확인하였다. 또한 표면 경도의 증가로 인해 Sag factor가 감소하는 경향을 확인하였다. 동일한 물 함량에서 NCO index가 증가함에 따라 우레탄과 우레아 결합이 이소시아네이트와 추가 반응하여 가교도와 경도가 증가하고 이에 따라 복원력이 감소함을 확인하였다.

• 한국산림과학회지
• /
• 제66권1호
• /
• pp.16-36
• /
• 1984

화강암질풍화토(花崗岩質風化土)의 미교란(未攪亂) 시료(試料)를 사용하여 일면(一面) 직접(直接) 전단시험(剪斷試驗)으로 측정(測定)한 전단강도(剪斷强度)와 함수비(含水比), 간극비(間隙比), 건조밀도(乾燥密度), 비중(比重)과의 관계(關係)를 통계(統計) 분석(分析)하였고, 화강암질풍화토(花崗岩質風化土)의 사방시공지(砂防施工地)에 식재(植栽)된 리기다소나무림(林)과 리기테-다소나무림(林)에서 토양단면(土壤斷面)을 만들어 산중식토양경도계(山中式土壤硬度計)로 토양(土壤)의 견밀도(堅密度)를 측정(測定)하고 수근분포(樹根分布)를 조사(調査)하여 통계(統計) 분석(分析)한 결과(結果) 다음과 같다. 1) 함수비(含水比), 간극비(間隙比)와 전단강도(剪斷强度) 간(間)에는 유의적(有意的)인 부(負)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 2) 건조밀도(乾燥密度)와 전단강도(剪斷强度) 사이에는 정(正)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 3) 비중(比重)과 전단강도(剪斷强度) 간(間)에는 유의적(有意的)인 상관관계(相關關係)를 인정(認定)할 수 없었다. 4) 전단강도(剪斷强度)에 영향(影響)을 미치는 영향요소(影響要素)의 직접효과(直接效果)의 크기는 함수비(含水比)>간극비(間隙比)>건조밀도(乾燥密度)의 순위(順位)이다. 5) 다중선형(多重線型) 회귀방정식(回歸方程式)의 분산분석결과(分散分析結果) 함수비(含水比)만이 회귀성(回歸性)이 인정(認定)되므로 함수비(含水比)를 독립변수(獨立變數)로 하여 전단강도(剪斷强度)를 추정(推定)하기 위한 회귀방정식(回歸方程式)은 제한(制限)된 건조밀도(乾燥密度)의 범위내(範圍內)에서 적합도(適合度)가 매우 높게 평가(評價)되었다. 6) 토양(土壤)의 견밀도(堅密度)는 토심(土深)이 깊어짐에 따라 높아진다. 7) 토양(土壤)의 지표경도(指標硬度)와 수근수(樹根數) 간(間)에는 유의적(有意的)인 부(負)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 8) 리기다소나무와 리기테-다소나무의 수근(樹根)은 토심(土深) 20cm까지에 대부분 분포(分布)하고 있었다. 9) 리기다소나무림(林)과 리기테-다소나무림(林)에서 측정(測定)한 토양(土壤)의 지표경도(指標硬度)를 독립변수(獨立變數)로한 회귀방정식(回歸方程式)으로 수근수(樹根數)를 추정(推定)할 수 있었으나 낮은 적합도(適合度)를 나타내었다.

• 한국정밀공학회지
• /
• 제21권3호
• /
• pp.100-108
• /
• 2004

Contamination of environment induces the shortage of drinkables. In this trend, the leakage of water that occurs by breakage or erosion of rubber valve seats is serious problem. Rubber is apt to cause breakage between two materials when they contact with each other. The possible way to avoid leakage of water by damage and breakdown of rubber is to replace that with metal. Because of this reason, nowadays, rubber is being substituted with metal as valve seat materials for water works. In tribology, a severe from of wear is characterized by local, macroscopic material transfer, removal, or formation of surface protrusions when two solid surfaces experience relative sliding under load. One of the major problems in sliding of metals is galling due to bad surface quality. Experimentally, there are various elements which influence on incipient galling, such as hardness, surface roughness, temperature, load, velocity and external environments. This paper is aimed at verifying the galling tendencies according to hardness, surface roughness, load and velocity and showing how much effect the factors have on the galling tendencies.

• 한국재료학회지
• /
• 제30권7호
• /
• pp.350-358
• /
• 2020

A variety of composite powders having different aluminum and carbon contents are prepared using various organic solvents having different amounts of carbon atoms in unit volume as ball milling agents for titanium and aluminum ball milling. The effects of substrate temperature and post-heat treatment on the texture and hardness of the coating are investigated by spraying with this reduced pressure plasma spray. The aluminum part of the composite powder evaporates during spraying, so that the film aluminum content is 30.9 mass%~37.4 mass% and the carbon content is 0.64 mass%~1.69 mass%. The main constituent phase of the coating formed on the water-cooled substrate is a non-planar α₂ phase, obtained by supersaturated carbon regardless of the alloy composition. When these films are heat-treated at 1123 K, the main constituent phase becomes γ phase, and fine Ti₂AlC precipitates to increase the film hardness. However, when heat treatment is performed at a higher temperature, the hardness is lowered. The main constitutional phase of the coating formed on the preheated substrate is an equilibrium gamma phase, and fine Ti₂AlC precipitates. The hardness of this coating is much higher than the hardness of the coating in the sprayed state formed on the water-cooled substrate. When hot pressing is applied to the coating, the porosity decreases but hardness also decreases because Ti₂AlC grows. The amount of Ti₂AlC in the hot-pressed film is 4.9 vol% to 15.3 vol%, depending on the carbon content of the film.

• 대한안전경영과학회지
• /
• 제5권1호
• /
• pp.115-128
• /
• 2003

To comparison the surface treatment methods of stone board materials, the results of Dorry's abrasive test were 23.4 for water-jet system and 18.9 for flame-burner system. Therefore abrasive hardness, the stone board materials by the water-jet system was greater than one by flame-jet system. As a result of Shore's hardness test, the stone board materials by water-jet system was twice greater than one by flame-jet system. Authors carried out microscopic observation to survey a defection of the composition minerals for two methods, but all of the both methods have not founded a defection. Therefore, the stone board materials by water-jet system was greater durability than one by flame-jet for the surface treatment methods.

• 한국농림기상학회지
• /
• 제16권1호
• /
• pp.59-71
• /
• 2014

본 시험은 왜성대목, 품종 및 저온에 따른 사과나무의 내동성을 조사하고자 실시하였다. 왜성대목은 M.9와 M.26이었고, 조사품종은 조생종인 '쓰가루', 중생종인 '홍로', 만생종인 '후지'였다. 저온처리는 $0^{\circ}C$부터 $-40^{\circ}C$ 사이였다. 조사부위는 대목, 원줄기, 측지, 꽃눈 및 잎눈이었다. 조사항목은 수분손실률, 전해질 누출률 및 발아율이었다. 결과를 살펴보면, 왜성대목에 따른 수분손실률, 전해질 누출률 및 발아율의 차이는 없었다. '후지'의 수분손실률은 '쓰가루' 및 '홍로'보다 낮았으나, 발아율은 '후지'가 '쓰가루' 및 '홍로'보다 높았다. 처리온도별 수분손실률과 전해질 누출률은 처리온도가 낮을수록 증가하였으나, 발아율은 반대로 감소하는 경향이 있었다. $-35^{\circ}C$ 처리에서 대목과 원줄기부위의 발아율은 측지부위보다 높았으며, 꽃눈의 발아율은 잎눈보다 낮았다. $-10^{\circ}C$에서의 경과일수에 따른 과대지의 발아율은 28일에 100%되었다가 35일에 50%정도로 급격하게 낮아졌다. 결론적으로, M.9과 M.26의 내동성 차이는 없었으나, 만생종의 내동성은 조, 중생종보다 큰 경향이 있었다. 꽃눈의 내동성은 $-30^{\circ}C$이하에서 급격하게 약해졌다.

• Restorative Dentistry and Endodontics
• /
• 제22권2호
• /
• pp.505-518
• /
• 1997

The objective of this investigation was to compare the effects of water storage on the aspect of hardness and diametral tensile strengths of four hybrid glass ionomer cements(two compomers and two resin-reinforced glass ionomers) with a resin composite material. One composite resin(Degufill Ultra), two compomers(Dyract, Compoglass Cavifil), and two resin-reinforced glass ionomers(Fuji Duet, Vitremer) were used in this study. Cylindrical specimens were prepared and stored at $36{\pm}1^{\circ}C$ in distilled water for 10 minutes after set, and then tested on an Instron testing machine(No.4467) at 1.0 mm/min displacement rate. Vicker's hardness and diametral tensile strengths as time elapsed were measured after aging in water for 10 minutes, 1 hour, 3 hours, 1 day, 3 days, 5 days and 7 days at $36{\pm}1^{\circ}C$. During the test of diametral tensile strength, stress-strain curves were obtained, from which the compressive modulus were calculated and compared. The structure of four set glass ionomer cement mass was observed on SEM(Hitachi, S-2300) after being etched with 9.6% hydrofluoric acid for 1 minute. The results were as follows; 1. The hardness of the experimental group(compomer and the resin reinforced glass ionomer cement) did not exceed the value of control group(Degufill Ultra). 2. Vicker's hardness of the Fuji Duet tended to increase succeedingly, Dyract was decreased after 3 hours in water, and Vitremer was the lowest. 3. The control group(Degufill Ultra) presented progressively on increased diametral tensile strength with time, Fuji Duet were decreased after 3 days, Compoglass Cavifil and Vitremer were decreased after 5 days in water storage. 4. Compressive modulus of the control group(Degufill Ultra) and Dyract were increased sharply timely, Fuji Duet and Vitremer were increased smoothly by lapse of time in water. Fuji Duet were stronger than Vitremer. On the other hand, Vitremer exhibited the lowest toughness. 5. The microstructure of compomer was similar with that of the composite resin(Degufill Ultra), and the fillers in resin-reinforced glass ionomer cements were noticed. It can be concluded that mechanical properties of hybrid glass ionomer cements is weaker than composite resin, and that the compomers or the resin-reinforced glass ionomers can not substitute the composite resins. A plenty of considerations should be done on the application of them to the area under the loading and high wear has a little adverse effect on the mechanical properties on the water storage for 7 days. The further research should be needed to confirm the advantage of the compomer.

• 동아시아식생활학회지
• /
• 제16권6호
• /
• pp.677-683
• /
• 2006

Glutinous rice cake(Chalduk) was made by varying the hours of soaking time of glutinous rice in the water(0, 4, 8, 12, 24 hours). After storage for various periods, the sensory and physical characteristics and the degree of gelatinization were examined in order to determine the effect of glutinous rice soaking period on the quality of Chalduk. The results of the study are summarized as follows. In the sensory test, 8-hour water soaking produced the significantly highest score for salty taste, while 0-hour water soaking had the lowest score. Four-hour water soaking had the significantly highest score for the degree of chewiness. Eight-hour water soaking had the significantly highest score for overall desirability. For the moisture content of Chalduk covered with bean flour, 8-hour water soaking produced the highest moisture content but the difference was not significant. For the degree of gelatinization, 8-hour water soaking had the highest maltose content, which confirmed the suitability of 8-hour water soaking glutinous rice. Eight-hour water soaking had the lowest hardness. With increasing storage period, the hardness sharply increased. Elasticity was higher for the long-period immersed samples than for the non-immersed samples. In conclusion, an 8-hour soaking time for glutinous rice in water was proposed to maximize the Chalduk quality.