• Journal of Korean Society on Water Environment
• /
• v.20 no.2
• /
• pp.163-169
• /
• 2004

Feasibility of using PE sheet laminated CSP(Corrugated steel pipe) to sewers were tested via corrosion and abrasion tests for PE sheet laminated CSP; 1) corrosion test for PE film and PE coated plate, 2) corrosion test for joint of PE sheet laminated CSP, 3) corrosion test for outside of PE sheet laminated CSP, and 4) abrasion test for inside of PE sheet laminated CSP. The results for the corrosion and abrasion tests are as follows. 1. Results for corrosion tests on PE films and zinc coated steel plates that were coated with PE films show that the surfaces of both PE were not changed compared to those of original PE samples. Furthermore, PE films maintained strong adhesion on the steel plates even though they were exposed to sewage and seawater provided cutting planes of the steel plates were treated with molding. But, results for corrosion tests on the spots that were previously cut off by a knife and a cutting planes of the steel plates were treated without molding show that steel plates have been corroded if they were exposed to sewage and seawater. 2. Results for corrosion tests on joints of PE sheet laminated corrugated steel using sewage show that gathering rust was observed at cutting plane of PE sheet laminated corrugated steel after 180 days, but PE film was not flaked off. However, PE film at cutting plane was flaked off when PE sheet laminated corrugated steel was exposed to seawater. Furthermore, flaking process was severely progressed at lockseam points of which the surfaces were not smooth. 3. Results for laying PE sheet laminated corrugated steel under the ground show that the surface of untouched PE film was almost identical to that of original PE film. However, the spots that were previously cut off by a knife and a cutting plane of PE sheet laminated corrugated steel have flaked off. 4. As a result of abrasion tests conducted with PE sheet laminated corrugated steel and sand, brilliance and thickness of PE was not greatly changed under the severe abrasion conditions. Therefore, the durability of PE sheet laminated corrugated steel for abrasion was determined to be good.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.4
• /
• pp.637-642
• /
• 2010

Pre-treatment steps of fresh produce as Saengshik raw materials are followed by initial clean-up, dipping, primary washing, and cutting. Hypochlorous acid solution was applied in the dipping step to reduce natural microflora. Also, procedures were changed by cutting, dipping and then primary washing, and the efficacy of hypochlorus acid was evaluated. Potatoes, carrots, kales, and angelicas were submerged in water or 100 ppm of hypochlorous acid for 5 min. After initial clean-up, the aerobic plate counts of potatoes, carrots, kales and angelicas were 4.7, 5.3, 5.6, and 5.7 log CFU/g, respectively. When samples were submerged into water, it only reduced the population of natural microflora by 0.2 to 1.1 log CFU/g, whereas when treated with hypochlorous acid, it reduced the population by 0.5 to 2.8 log CFU/g. Reductions of natural microflora in green leafy vegetables were more highly achieved than bulbs such as potatoes and carrots. However, the numbers of natural microflora were increased after cutting step. To control the cross contamination at the cutting process, the process was changed as follows: initial clean-up, cutting, dipping in hypochlorous acid, and then primary washing. It showed effective reduction of the population by 2.3 to 3.2 log CFU/g. Hypochlorous acid solution could be useful as a sanitizer for surface washing of fresh vegetables.

• Journal of Environmental Science International
• /
• v.13 no.11
• /
• pp.1001-1007
• /
• 2004

The rapid industrialization and urbanization in Osaka Bay have produced many serious water pollution problems since the 1960s. A symbolic phenomenon is algae bloom (red tide), which occurred 53 times in 1976. The special law was enacted in 1973 and a number of administrative steps were taken, such as cutting COD loading, reductions in phosphorus (P) and restriction of land reclamation. As a result, the pollution of Osaka Bay has gradually been reduced, and the environment has been improved to some extent. In this study, to analyze the relations between water qualities as well as a social, economic activity by the coastal zone, the water quality data in Osaka Bay of 70 years past since 1921 were collected. Data such as population, livestock, fertilizer, industrial product etc. were also collected for estimating nutrients flowing into bay from land. It was found that the water quality was changed of a similar trend of estimated nutrients load, with delay of about four or five years.

• Journal of Korean Society of Forest Science
• /
• v.66 no.1
• /
• pp.74-78
• /
• 1984

The highest cutting ratio and the best growth performance of the P. alba, P. alba ${\times}$ P. glandulosa and P. glandulosa were at -0.05 bars of soil water potential (${\Psi}_s$). Their growth and rooting ability of cuttings were better in suitable soil moisture contents, 19.650, but were worse in low soil moisture contents, 11.41% and 16.66%, respectively. Specially, P. alba ${\times}$ P. glandulosa appeared hybrid vigor in high soil water potential (${\Psi}_s$= -0.05 bars) but not appeared it below ${\Psi}_s$ = -0.5 bars. It is believed that P. glandulosa is a natural hybrid between P. davidiana and P. alba in view of morphological characteristics. Aspen, normally, does not have the rooting ability of cuttings, however, P. glandulosa showed the rooting ability, though the ratio was low, 23%. It is estimated that this rooting ability was originated from P. alba. In addition, its growth rate was between P. alba and P. davidiana, and the sensitivity of water requirement for the growth was also really equal to P. alba. This facts prove P. glandulosa to be natural hybrid between P. alba and P. davidiana.

• Journal of Animal Science and Technology
• /
• v.66 no.4
• /
• pp.645-662
• /
• 2024

Climate change, driven by the natural process of global warming, is a worldwide issue of significant concern because of its adverse effects on livestock output. The increasing trend of environmental temperature surging has drastically affected meat production and meat product quality, hence result in economic losses for the worldwide livestock business. Due to the increasing greenhouse gas emissions, the situation would get prolonged, and heat exposure-related stress is expected to worsen. Heat exposure causes metabolic and physiological disruptions in livestock. Ruminants and monogastric animals are very sensitive to heat stress due to their rate of metabolism, development, and higher production levels. Before slaughter, intense hot weather triggers muscle glycogen breakdown, producing pale, mushy, and exudative meat with less water-holding capacity. Animals exposed to prolonged high temperatures experience a decrease in their muscle glycogen reserves, producing dry, dark, and complex meat with elevated final pH and increased water-holding capacity. Furthermore, heat stress also causes oxidative stresses, especially secondary metabolites from lipid oxidation, severely affects the functionality of proteins, oxidation of proteins, decreasing shelf life, and food safety by promoting exfoliation and bacterial growth. Addressing the heat-related issues to retain the sustainability of the meat sector is an essential task that deserves an inclusive and comprehensive approach. Considering the intensity of the heat stress effects, this review has been designed primarily to examine the consequences of hot environment temperatures and related stresses on the quality and safety of meat and secondarily focus on cutting edge technology to reduce or alleviate the situational impact.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.3 s.16
• /
• pp.5-10
• /
• 2006

This paper investigates cutting qualities after laser dicing and predicts the problems that can be generated by laser dicing. And through 3 point bending test, die strength is measured and the die strength after laser dicing is compared with the die strength after mechanical sawing. Laser dicing is chiefly considered as an alternative to overcome the defects of mechanical sawing such as chipping on the surface and crack on the back side. Laser micromachining is based on the thermal ablation and evaporation mechanism. As a result of laser dicing experiments, debris on the surface of wafer is observed. To eliminate the debris and protect the surface, an experiment is done using a water soluble coating material and ultrasonic. The consequence is that most of debris is removed. But there are some residues around the cutting line. Unlike mechanical sawing, chipping on the surface and crack on the back side is not observed. The cross section of cutting line by laser dicing is rough as compared with that by mechanical sawing. But micro crack can not be seen. Micro crack reduces die strength. To measure this, 3 point bending test is done. The die strength after laser dicing decreases to a half of the die strength after mechanical sawing. This means that die cracking during package assembly can occur.

• Korean Journal of Food Science and Technology
• /
• v.38 no.2
• /
• pp.237-240
• /
• 2006

Seventy-one marine bacteria decomposing sea tangle (Laminaria japonica) into single cell detritus (SCD) were isolated from sea water, sea tangle, sea mustard (Undaria pinnatifida), sea urchin (Anthocidaris crassispina), star fish (Acanthaster planci), and turban cell (Batillus cornutus), among which 14 strains decreased cutting strength of sea tangle and had alginate-degrading activity. Marine bacterium No. 34 isolated from turban cell showed lowest cutting strength of sea tangle, strongest alginate-degrading activity, and produced high content of $5-10\;{\mu}m$ SCD from sea tangle. This strain was identified as Vibrio sp. based on morphological, physiological, and biochemical characteristics and named as Vibrio sp. YKW-34.

• Journal of Animal Science and Technology
• /
• v.63 no.3
• /
• pp.510-519
• /
• 2021

One of the most pressing issues facing the dairy industry is drought. In areas where annual precipitation is low, irrigation for growing feed presents the greatest water-utilization challenge for dairy producers. Here, we investigated the effects of cultivar and harvest days after planting (DAP) on dry matter (DM) yield and nutritive value of teff (Eragrostis tef), a warm-season annual grass native to Ethiopia that is well adapted to drought conditions. Eighty pots were blocked by location in a greenhouse and randomly assigned to four teff cultivars (Tiffany, Moxie, Corvallis, and Dessie) and to five harvest times (40, 45, 50, 55, or 60 DAP). Cultivars had no effect on DM yield and nutritive value. As harvest time increased from 40 to 60 DAP, DM yield and ash-free neutral detergent fiber (aNDFom) concentrations increased, while crude protein (CP) concentrations and in vitro NDF digestibility decreased. To assess carryover effects of time of harvest on yield and nutritive value, two additional cuttings were taken from each pot. Increasing first-cutting harvest time decreased CP concentrations in the second cutting and reduced DM yields in the second and third cutting. Harvesting teff between 45 and 50 DAP best optimized forage yield and nutritive value in the first and subsequent cuttings.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.6
• /
• pp.139-151
• /
• 2007

To protect the surface of ground-cutting slopes and ground-raised slopes and to recover environment-friendly slopes at the national road expansion construction between Gamchon and Yaechon, test-construction work was done using several modes of hydro-seeding measures to select a suitable construction method through the field survey; the results were as follows : As a result of survey on physio-chemical characteristics of soil, the average soil inclination on ground-raised slopes was from 4.73 mm to 5.37 mm; the average soil acidity was from pH 6.47 to 6.73; the average soil humidity was within the scope of 0.57~1.70 %,; the average soil inclination on ground-cutting slopes was 9.17~10.43mm; the average soil acidity was pH 6.67~6.77 and the average soil humidity was within the scope of 0.53~1.27 %; considered overall, they showed generally satisfactory base materials for plant breeding. As a result of the number of sprouting individuals, the average sprouting number of individuals on test spots executed by Coir net with Seed spray construction methods and the average number of sprouting individuals on other test spots executed by furrow-digging with Seed spray and Straw mat-mulching measures were 1,172 number of per square meter and 970 number of per square meter respectively; thus they showed higher numerical value comparing with other test spots. Likewise, the average number of sprouting individuals on test spots of the ground-cutting slopes executed by Coir net with Seed spray method and the average number of sprouting individuals on other test spot executed by furrow-digger with Seed spray and Straw mat-mulching measures were found to be 1,107 number of per square meter and 1,105 number of per square meter respectively, whose numerical value showed rather higher other test spots. As a result of a survey on living plants' breeding index [dried weight], the weight in dried state on test spots executed by Coir net with Seed spray method and other test spots executed by furrow-digger with Seed spray and Straw mat-mulching measures on both ground-raised and ground-cutting slopes was found to be higher and showed similar characteristics statistically. As a result of survey on the surface-covering degree of ground-raised slopes, nine weeks after test construction, test spots executed by Coir net with Seed spray method and other test spots executed by furrow-digger with Seed spray and Straw mat-mulching measures showed commonly more than 70% of surface-covering degree, but other test spots showed only below 35% of surface covering degree; especially in case of test spots by Verdvol seed spray measures, they showed 10% of the lowest surface-covering. Surface-covering degree on the test spot of ground-cutting slopes nine weeks after test construction showed more than 75% both executed by Coir net with Seed spray construction method and executed by furrow-digger with Seed spray and Straw mat-mulching measures. As a result of survey on appearing plants on the test spots, there dominates Eragrostis curvula both on ground-raised slopes and on ground-cutting slopes with other seeding plant life's lower breeding and there appear intruders, such as Setaria viridis Beauv, Digitaria sanguinalis Scop, and Chenopodium album var.centrorubrum Makino. As for water-borne excavation and soil's washing-away on the slopes, there happened less washing-away and water-borne excavation with good breeding of plant life on test spots executed both by Coir net with Seed spray construction method and by furrow-digger with Seed spray and Straw mat-mulching measures, but there happened much more soil's washing-away along with water-home excavation at the test spot executed by Seed spray with measures. After the research results of test construction sites are examined overall, it's presumed that furrow-digger with Seed spray and Straw mat-mulching measures [interval between lines is 40cm, 5cm in depth] will be preferred to prevent erosion and water-home excavation of slopes located within the construction sites.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.537-542
• /
• 2000

Wire deflection, surface roughness and roundness were observed on changing discharge time for electrical discharge machining(EDM) of STD-11 in various conditions of thickness. The wire deflection was decreased as increasing discharge time and wire tension. The deflection is the smallest at the speed of wire of 10.6m/min and the water specific resistivity of 5k$\Omega$.cm. The deflection is found to be decreased as increasing dwell time. But if the water pressure is high, it is found not to be changed after the vibration of 4sec. The component of copper(Cu) and zinc(Zn), which is the main material of wire electrode, is observed for rough wire-cutting EDM of STD-11. This phenomena is found to be similar in spite of the change of EDM energy level. But it will be improved by changing the material and the shape of wire. The roundness of middle is found to be worse than that of upper and it is increased as the thickness of material is increased.