• Science of Emotion and Sensibility
• /
• v.10 no.1
• /
• pp.55-68
• /
• 2007

This paper describes a Voice User Interface(VUI) method and a design guideline tool which supports the studies for domestic appliance. This issue covers specification of user requirement and selection of appropriate VUI to represent speech generation. The criteria for paper is interaction design to enhance user engagement. The studies were carried out to measure prototype of domestic appliance such as a refrigerator, a washing machine, a Gimchi refrigerator, an oven range, a dishwasher and an air conditioner. This paper is presented a study of user preferences and suitability. The results of these findings to voice interface design are discussed and it is suggested that VUI guideline and optimal prototyping can provide a useful application tools in the design process.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.2
• /
• pp.79-85
• /
• 2018

A two-way pump can reduce costs by draining and circulating water out and into the drum of the washing machine using a single motor whereas a conventional one-way pump uses two motors for doing the same function. However, when the water is drained through the drainage outlet in the two-way pump casing, a backward or inhalation flow occurs and the water flows to the circulation outlet. Likewise, when the water is circulated, the backward flow or inhalation makes the water flow to the drainage outlet. In this study, design optimization of the two-way pump casing is performed to maximize its performance while improving backward flow and inhalation occurring inside of the pump casing. For this, design variables of the pump casing that mainly affect the performance of the pump such as flow rate and torque of the motor were selected through the analysis of mean. Using response surface models for the performances, the ratio of the flow rate to the torque was maximized with satisfying the constraints for the back flow and inhalation through design optimization.

• Environmental and Resource Economics Review
• /
• v.24 no.3
• /
• pp.463-488
• /
• 2015

A more detailed design of offset system is needed according to the emission trading system started in 2015. This study aims to estimate the supply of potential offset that can be secured by expanding high-efficiency household electric appliances. The target commodities for analysis are three different householding electric appliances: TV, washing machine, electric fan, refrigerator and air conditioner. By using the ARDL model, we estimated the coefficients of diffusion of these high-efficiency appliances from 2016 to 2022. Then, the potential supply of offset was drawn by calculating the amount of electricity saving by efficiency improvement and by applying the rates of carbon exchange. Supposing that the electricity savings rates of high-efficiency appliances are each 10% and 20%, the accumulated carbon decrement in 2022 was respectively $361,899CO_2t$ and $723,797CO_2t$. The appliance that showed the biggest carbon decrement was air conditioner, and the second biggest was refrigerator and the next was TV, followed by washing machine, electric fan.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1123-1129
• /
• 2015

A pair of two-way valves typically is used in automotive washing machines, where the water flow direction is frequently reversed and highly pressurized clean water is sprayed to remove the oil and dirt remaining on machined engine and transmission blocks. Although this valve system has been widely used because of its competitive price, its application is sometimes restricted by surging effects, such as pressure ripples occurring in rapid changes in water flow caused by inaccurate valve control. As an alternative, one three-way reversing valve can replace the valve system because it provides rapid and accurate changes to the water flow direction without any precise control device. However, a cavitation effect occurs because of the complicated bottom plug shape of the valve. In this study, the cavitation index and percent of cavitation (POC) were introduced to numerically evaluate fluid flows via computational fluid dynamics (CFD) analysis. To reduce the cavitation effect generated by the bottom plug, the optimal shape design was carried out through a parametric study, in which a simple computer-aided engineering (CAE) model was applied to avoid time-consuming CFD analysis and difficulties in achieving convergence. The optimal shape design process using full factorial design of experiments (DOEs) and an artificial neural network meta-model yielded the optimal waist and tail length of the bottom plug with a POC value of less than 30%, which meets the requirement of no cavitation occurrence. The optimal waist length, tail length and POC value were found to 6.42 mm, 6.96 mm and 27%, respectively.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.31 no.12
• /
• pp.1784-1792
• /
• 2007

This study set out to identify the problems with hat labels and to search for improvement measures by examining and analyzing consumers' practice of managing their hats. It also intended to provide accurate and enough information about how to keep and wash hats and thus help consumers use their hats for a long period. In an attempt to investigate how consumers wash and manage their hats, a survey was carried out to 395 individuals in their twenties and over who owned hats living in urban areas including Seoul, and were quota sampled according to age and gender. The survey period is March to April 2007. The collected data were statistically treated with the SPSS 12.0 program in terms of frequency, percentage, mean, standard error, cross tabulation, t-test, and one-way ANOVA. The findings were as followed. First, the respondents were in the average level of perceiving and practicing the washing methods of their hats. The female respondents who had more experiences with laundering than the males knew and practiced the washing methods for hats better than males. Second, compared to other clothing items, hat wearers were more likely to pay careful attention to their hats by putting their hats in a laundry net and applying a laundry detergent for wool fabrics when using a washing machine or washing their hats with their own hands. And third, most of the hat wearers were aware of the importance of hat labels and showed a lower level of trust in them than other clothing items. The suppliers need to offer accurate and practical labels in order to regain the consumers' trust. Many consumers had some difficulties figuring out the size system of hats. In particular, the male consumers had a low level of perception of labels, which implies that there should be specific efforts to educate them about general labels.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.4
• /
• pp.295-302
• /
• 2008

This paper examines the design and the performance of a PMA-RSM(permanent-magnet assisted reluctance synchronous motor) for washing machine. A FEM(finite element method) is used to analyze performance and maximum torque characteristic of the proposed PMA-RSM. The designed motor is a combination of salient poles, which is making reluctance torque, and permanent magnet which are located on the air-gap of rotor to get a enough torque during low speed resign. Typical flux barrier type reluctance synchronous motor and the effects of adding magnet into the flux barrier of the rotor of a PMA-RSM are compared and examined. Also the maximum torque point of the reluctance torque by reluctance and reaction torque by magnetic alignment torque, which is in barrier, of the proposed PMS-RSM are derived through simulation. Using this results, the characteristics analysis of a performance, an average torque and a torque ripple of flux barrier RSM and the proposed PMA-RSM are performed through FEM under the saturation effect respectively.

• Journal of Biosystems Engineering
• /
• v.30 no.1 s.108
• /
• pp.25-31
• /
• 2005

There are more than three hundred garlic peeling facilities in Korea and most of them use pressurized air for skin peeling operation. One of the major problems of using air for the peeling operation is the occurrence of excessive bruises on the flesh of peeled garlic which causes easy microbial contamination and shortening of the shelf lift. To reduce the occurrence of bruises during the peeling operation, a new type of garlic peeling system was developed which use pressurized water. In this system, high pressure water jets were used to separate garlic bulbs and to peel the skin of garlic cloves. Six commercial systems of this type had been developed and installed at several locations in Korea. The design and performance of the latest system according to three pressure levels were described in this paper. Peeling efficiency of the system was as high as $64.7\%$ in one cycle of peeling operation by three chambers installed in series. Incorporation of a sorting system based on machine vision and re-circulation of unpeeled and partially-peeled garlic enhanced peeling efficiency by additional $30\%$, resulting in total peeling efficiency of the final products of approximately $95\%$. Peeling capacity of the system was over 400 kg per hour.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.482-489
• /
• 2020

This study conducted a prototype development and evaluation by performing die-casting mold design, mold manufacturing, and injection condition optimization based on flow and solidification analysis to meet the needs of the coupling parts produced by die casting. Through flow analysis, the injection conditions suitable for 100% filling in the cavity were found to be a molten metal temperature of 670 ℃, injection speed of 1.164 m/s, and filling pressure of 6.324~18.77 MPa. In addition, solidification close to 100 % occurred in all four cavities when the solidification rate was 69.47 %. A defect inspection on the surface and inside the product revealed defects, such as poor molding and pores. In addition, the dimensions of the injected product were within the target tolerance and showed good results. Through the feedback of the results of flow and solidification analysis, it was possible to optimize the mold design, and the injection optimization conditions were confirmed to be a total cycle time of approximately 6.5 seconds. Good quality carrier parts with an average surface hardness of approximately 45 mm from the gate measured at 97.48(Hv) could be produced.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.9
• /
• pp.1268-1273
• /
• 2011

The present study was conducted to determine a feasible method of protein concentrate extraction from rice bran (RBPC) and its effect as a substitution for skim milk in early weaning pig diets. An investigation to extract protein concentrate from full fat rice bran was undertaken to determine the best ratio of water and rice bran, the amount of NaOH and a HCl solvent to use in a simple paddle-type mixer with modified spinning to produce RBPC. The results stated that the best ratio for water mixing in the RBPC extraction process was 1:5 with 20 g NaOH and 30 min in a paddle-type mixer at 300 rpm. A mix of 250 ml 0.2 N HCl was optimum for neutralization and protein precipitation. After the fluid was spun out with a washing machine, the sediment was left for 12-14 hours to complete the filtration. One kilogram of rice bran could produce an average of 324.5 gram RBPC and it contained 3.40% ash, 496.48 kcal of GE/100 gram, 1.94% crude fiber, 28.20% ether extract, 7.64% moisture and 16.66% crude protein, respectively. A total of 45 crossbred piglets, weaned at 3 weeks of age were allotted into control diet (A) and dietary treatments formulated with a four different rates of RBPC substitution for skim milk at a percentage of 25 (B), 50 (C), 77 (D) and 100 (E) respectively, in a randomized complete block (RCB) design. All piglets had free access to feed and water until 8 week of age when the experiment ended. Feed intake, average daily gain, growth rate and feed efficiency were not affected by dietary treatments. Blood test parameters after completion of the growth trial indicated normal health. Even though the mean of cell hemoglobin concentration was significantly different between treatments (p<0.05) it was still within the normal range. The cost difference for BW gain of 100% RBPC substituted for skim milk in the weaning diet was approximately 35% lower than that of the control and the relative cost of production was 96.67, 92.85, 70.75 and 64.48% lower for the replacement of 25, 50, 75 and 100% of skim milk respectively. These results implied that this technology is feasible for use by small scale farmers to improve their self-reliance.

• Journal of Korean Dental Science
• /
• v.12 no.1
• /
• pp.13-19
• /
• 2019

Purpose: The aim of this study was to compare the flexural strength of provisional fixed dental prostheses which was three-dimensional (3D) printed by several build directions. Materials and Methods: A metal jig with two abutment teeth and pontic space in the middle was fabricated. This jig was scanned with a desktop scanner and provisional restoration was designed on dental computer-aided design program. On the preprocessing software, the build angles of the restorations were arranged at $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $90^{\circ}$ and support was added and resultant structure was sliced to a thickness of $100{\mu}m$. Processed restorations were printed with digital light processing type 3D printer using poly methyl meta acrylate-based resin. After washing and post-curing, compressive loading was applied at a speed of 1 mm/min on a metal jig fixed to a universal testing machine. The maximum pressure at which fracture occurred was measured. For the statistical analysis, build direction was set as the independent variable and fracture strength as the dependent variable. One-way analysis of variance and Tukey's post hoc analysis was conducted to compare fracture strength among groups (${\alpha}=0.05$). Result: The mean flexural strength of provisional restoration 3D printed with the build direction of $0^{\circ}$ was $1,053{\pm}168N$; it was $1,183{\pm}188N$ at $30^{\circ}$, $1,178{\pm}81N$ at $45^{\circ}$, $1,166{\pm}133N$ at $60^{\circ}$, and $949{\pm}170N$ at $90^{\circ}$. The group with a build direction of $90^{\circ}$ showed significantly lower flexural strength than other groups (P<0.05). The flexural strength was significantly higher when the build direction was $30^{\circ}$ than when it was $90^{\circ}$ (P<0.01). Conclusion: Among the build directions $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $90^{\circ}$ set for 3D printing of fixed dental prosthesis, an orientation of $30^{\circ}$ is recommended as an effective build direction for 3D printing.