• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.8
• /
• pp.726-732
• /
• 2011

Straight absorptive silencers have been designed to reduce the noise level of a centrifugal blower. Three-dimensional boundary element method is used for the design of absorptive silencers which consist of a perforated main pipe and a outer chamber filled with fibrous material. The experimental results show that the absorptive silencer reduces up to 8 dB(A) in the overall sound pressure level of the blower and up to 15 dB at the blade passing frequency. It is also found that the gap between the silencer and the impeller may substantially alter the acoustic performance of the silencers. The transmission loss predicted by the boundary element method follows overall trends of the measured insertion loss. The experiments also show that the impact of the silencers on the aerodynamic performance of the blower is minimum.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.10
• /
• pp.1636-1643
• /
• 2003

In this study, bolted joint made of Glass-Mat Reinforced Thermoplastics (GMT) specimen was under tensile loading to investigate the relation between joint strength and glass-fiber weight fraction of the flat plate specimen. The effect of molding conditions such as the initial size of a GMT charge and molding temperatures was investigated under plane strain condition. In consideration of the specimen geometry, minimum end distance and width of the specimen to induce the bearing fracture mode of the bolted joint were determined. And finally, the effect of the outer diameter of washer and clamping pressure on joint strength was also investigated. Since joint strength is dependent on the local glass-fiber weight fraction, experimentally measured strength was modified, considering its irregular values of the specimen molded under various processing conditions in order to obtain a reasonable correlation between the two.

• Journal of Auto-vehicle Safety Association
• /
• v.9 no.3
• /
• pp.39-45
• /
• 2017

Two-wheeled motorcycles rarely use windscreen wipers in general. However, if two or more wheeled motorcycles with upper body employ windscreen wiper systems, clear visibility should be ensured regardless of weather conditions. The windscreen wiper systems include washers, defrosting, and demisting. As demands for the personal mobility are rapidly increased, the related global safety standards for motorcycles with upper body have been revised accordingly. Currently only EU regulations issue the provisions of windscreen wiper systems for L-category vehicles, which characterize two or more wheeled motorcycles. Therefore, in order to agree with international safety standards, it is necessary to revise KMVSS (Korea Motor Vehicle Safety Standards) for motorcycles. Here, KMVSS regarding windscreen wiper systems for motorcycles are studied considering the EU regulations. It is expected that the findings in this study are useful for future amendment of KMVSS.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.7
• /
• pp.591-595
• /
• 2015

The roller rig tester for safety performance evaluation of wheel derailment is a test facility which can give the test load condition to the test wheel, similar to the actual dynamic condition in actual running condition. This study describes the evaluation result on the durability of the resilient wheel equipped with the ring damper and the damping material, and installed in the half part of a full scaled bogie in combination with the primary spring when it rotates under the dynamic condition. The evaluation result on durability of resilient wheel after load test of 2 million cycles shows that the safety of wheel is not affected by the applied load in visual inspection and nondestructive test, however, in the bolt used for fastening the ring damper to the wheel the loosening was found. Accordingly the use of self-locking nut and washer is recommended.

• Journal of Families and Better Life
• /
• v.19 no.5
• /
• pp.259-277
• /
• 2001

The purpose of this study was to identify household’s level and standard of consumption and their related variables in order to derive some useful implications for developing sustainable lifestyle. Data were collected from 567 household wives living in Seoul and the five Metropolitan cities in Korea. The results showed that most households owned such goods as central heating system, shower and bath, refrigerator, microwave oven, vacuum cleaner, washer. TV video player, personal computer, mobile phone, and car. They thought that most of the goods were necessary for the desired level of living and has a strong aspiration to buy those goods. This implied a tendency of uniformity in need perceptions and consumption patterns among Korean households. However, level and standard of consumption measured in selected living area differed according to age. education family size, household income, occupation, and the size housing, which showed that different approach was needed for developing sustainable lifestyle according to these variables.

• Journal of the Korean Solar Energy Society
• /
• v.23 no.4
• /
• pp.63-70
• /
• 2003

It is very important to improve the insulation performance of curtain wall anchoring unit since it is composed of materials with high thermal conductivity, such as aluminium, steel and so on. This study aims to evaluate the heating energy performance and economical efficiency of various alternatives which are different in position and material of insulation. As results, alternative of inserting the urethane washer & pad and coating the anchoring unit with urethane foam can improve the heating energy performance and L.C.C(Life Cycle Cost) by 6.33% and 0.95%, respectively, as compared with the existing case.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.215-216
• /
• 2015

세탁기의 탈수 행정 시, 터브 내 세탁포가 고르게 분포되어 있지 않으면 세탁포가 한쪽방향으로 쏠려 터브가 크게 흔들리는 언밸런스 현상이 발생하게 된다. 이런 언밸런스 현상은 전동기 및 세탁기에 기구적인 손상을 발생시키기 때문에 즉시 감지하여 탈수 행정을 중지시키도록 해야 한다. 본 논문에서는, 세탁기의 언밸런스 현상이 발생 시 나타나는 전동기의 기계적인 주파수를 갖는 전류 리플을 가변 밴드패스 필터를 이용하여 측정한다. 측정된 전류 리플을 바탕으로 언밸런스 현상을 감지하는 알고리즘을 제안한다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.7
• /
• pp.974-981
• /
• 2012

This paper studied about the measurement method of the instantaneous dynamic load characteristics. this experimental study, we derived the instantaneous washing load characteristics and inertial moment characteristics according to the amount of laundry and water level. Also, this studied about the dynamic driving characteristics simulation method for the prediction of washing performance based on this load characteristics analysis. For this study, the design parameters of the driving motor are obtained by FEM analysis and the experiment. By using theses motor parameters and load characteristics, the instantaneous driving characteristics simulation is accomplished and it is verified with the experimental result of various driving conditions. The results of this paper would be very useful to the prediction of washing mode operation characteristics, and it can be also utilized to the washer motor control algorithm design for the washing performance improvement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.832-837
• /
• 2001

In this paper, we analyzed the characteristic of the broken section for bolts fastening the generator casing, and according to the frequency analysis, we grasped the characteristic of the excited force, traced the path of the exciting source so that we examined a factor of transient vibration of the generator casing. Even if it appears transient vibration again, we applied spring washer and more tensile bolt to the casing to minimize the fracture. By solving troubles of the generator rotor, we reduced the vibration amplitude to the normal condition. So we obtain much more the reliablility of the generator.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.6
• /
• pp.1059-1075
• /
• 2017

The objective of this study was to evaluate the freezing and thawing resistance of the existing drainage system for leakage treatment of underground concrete structures operating in cold regions. The freezing and thawing test was conducted on 4 types of drainage system specimens to evaluate the freezing and thawing resistance of the drainage system. The freezing and thawing resistance was evaluated on 4 types of Hotty-gel, as a waterproofing material, connection methods and on two methods to fix the drainage board with Hotty-gel on the surface of cement concrete specimen. One cycle of the freeze-thaw testing was 48 hours (24 hours of freezing and 24 hours of thawing), and the temperatures of freezing and thawing were at $-18^{\circ}C$ and $10^{\circ}C$, respectively. Among the 4 types of Hotty-gel connection methods, leakage occurred after 28 cycles (8 weeks) of freeze-thawing only in the Hotty-gel connection method with the 'V' groove applied to the corner of the drainage board. No leakage occurred in the 3 types of Hotty-gel connection methods. In two fixing methods, leakage occurred in the method of fixing the drainage board on the cement concrete specimen using the washer, screw and plastic wall plug. Leakage occurred at one point after 10 cycles (3 weeks) of freezing and thawing. After 28 cycles (8 weeks) of freezing and thawing, leakage point increased to 5 points. As time passed, the leak point was not increased, but the amount of leakage was increased at each leak point. The Hotty-gel connection method with cross-sectional diagonal shape was evaluated to be the highest in the production efficiency considering the production time and manufacturing method of the Hotty-gel connection shape. In the construction efficiency considering the construction time and construction method, the fixing method of air nailer, fixed nail and washer was superior to that of the washer, screw and plastic wall plug.