• Wind and Structures
• /
• v.26 no.5
• /
• pp.317-329
• /
• 2018

Wake characteristics of the flow over a finite square prism at different incidence angles were experimentally investigated using an open-loop wind tunnel. A finite square prism with a width D = 15 mm and a height H = 7D was vertically mounted on a horizontal flat plate. The Reynolds number was varied from $6.5{\times}10^3$ to $28.5{\times}10^3$ and the incidence angle ${\alpha}$ was changed from $0^{\circ}$ to $45^{\circ}$. The ratio of boundary layer thickness to the prism height was about ${\delta}/H=7%$. The time-averaged velocity, turbulence intensity and the vortex shedding frequency were obtained through a single-component hotwire probe. Power spectrum of the streamwise velocity fluctuations revealed that the tip and base vortices shed at the same frequency as that ofspanwise vortices. Furthermore, the results showed that the critical incidence angle corresponding to the maximum Strouhal number and minimum wake width occurs at ${\alpha}_{cr}=15^{\circ}$ which is equal to that reported for an infinite prism. There is a reduction in the size of the wake region along the height of the prism when moving away from the ground plane towards the free end.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.2
• /
• pp.99-110
• /
• 2010

The DES analysis of strong compressibility flow, LES mode is intentionally performed in boundary layer with the conventional empirical constant $C_{DES}$ value of 0.65. In this study, an expression is suggested to determine the $C_{DES}$ value dynamically by using a distribution function of the ratio of turbulence length scale and wall distance which is used in S-A DDES model for RANS mode protection. The application of the dynamic $C_{DES}$ presents better prediction than previous results those used constant but different $C_{DES}$ values.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.1
• /
• pp.48-55
• /
• 2017

Aeroacoustic computation of a fully-developed turbulent pipe flow at $Re_{\tau}=175$ and M = 0.1 is conducted by LES/LPCE hybrid method. The generation and propagation of acoustic waves are computed by solving the linearized perturbed compressible equations (LPCE), with acoustic source DP(x,t)/Dt attained by the incompressible large eddy simulation (LES). The computed acoustic power spectral density is closely compared with the wall shear-stress dipole source of a turbulent channel flow at $Re_{\tau}=175$. A constant decaying rate of the acoustic power spectrum, $f^{-8/5}$ is found to be related to the turbulent bursts of the correlated longitudinal structures such as hairpin vortex and their merged structures (or hairpin packets). The power spectra of the streamwise velocity fluctuations across the turbulent boundary layer indicate that the most intensive noise at ${\omega}^+$ < 0.1 is produced in the buffer layer with fluctuations of the longitudinal structures ($k_zR$ < 1.5).

• Computers and Concrete
• /
• v.17 no.2
• /
• pp.173-188
• /
• 2016

Generally, thermal stress induced by hydration heat causes cracking in mass concrete structures, requiring a thorough control during the construction. The prediction of the thermal stress is currently undertaken by means of numerical analysis despite its lack of reliability due to the properties of concrete varying over time. In this paper, a method for the prediction of thermal stress in concrete structures by adjusting thermal stress measured by a thermal stress device according to the degree of restraint is proposed to improve the prediction accuracy. The ratio of stress in concrete structures to stress under complete restraint is used as the degree of restraint. To consider the history of the degree of restraint, incremental stress is predicted by comparing the degree of restraint and the incremental stress obtained by the thermal stress device. Furthermore, the thermal stresses of wall and foundation predicted by the proposed method are compared to those obtained by numerical analysis. The thermal stresses obtained by the proposed method are similar to those obtained by the analysis for structures with internally as well as externally strong restraint. It is therefore concluded that the prediction of thermal stress for concrete structures with various boundary conditions using the proposed method is suggested to be accurate.

• Wind and Structures
• /
• v.11 no.5
• /
• pp.413-426
• /
• 2008

A wind tunnel study has been carried out to determine the influence of spacing between buildings on wind characteristics above rural and suburban type of terrain. Experiments were performed for two types of buildings, three-floor family houses and five-floor apartment buildings. The atmospheric boundary layer (ABL) models were generated by means of the Counihan method using a castellated barrier wall, vortex generators and a fetch of roughness elements. A hot wire anemometry system was applied for measurement of mean velocity and velocity fluctuations. The mean velocity profiles are in good agreement with the power law for exponent values from ${\alpha}=0.15$ to ${\alpha}=0.24$, which is acceptable for the representation of the rural and suburban ABL, respectively. Effects of the spacing density among buildings on wind characteristics range from the ground up to $0.6{\delta}$. As the spacing becomes smaller, the mean flow is slowed down, whilst, simultaneously, the turbulence intensity and absolute values of the Reynolds stress increase due to the increased friction between the surface and the air flow. This results in a higher ventilation efficiency as the increased retardation of horizontal flow simultaneously accompanies an intensified vertical transfer of momentum.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.56 no.1
• /
• pp.81-88
• /
• 2014

Accurate wind data is essential for predicting airborne spread of virus. OpenFOAM was used for computational fluid dynamics (CFD) simulation procedure which is under GNU GPL (General Public License). Using complex terrain, DEM (Digital Elevation Map) that was prepared from GIS information covering a research site is converted to a three dimensional surface mesh that is composed by quad and full hexahedral space meshes. Around this surface mesh, an extended computational domain volume was designed. Atmospheric flow boundary conditions were used at inlet and roughness height and was considered at terrain by using rough wall function. Two different wind conditions that was relatively stable during certain periods were compared in 3 different locations for validating the accuracy of the CFD computed solution. The result shows about 10 % of difference between the calculated result and measured data. This procedure can simulate a prediction of time-series data for airborne virus spread that can be used to make a web-based forecasting system of airborne virus spread.

• Journal of the Korean Institute of Rural Architecture
• /
• v.13 no.2
• /
• pp.9-21
• /
• 2011

This study aims to examine and research the characteristics of apartment landscape at the street from a view that apartments are the major element of a cityscape and many apartments form a street today. Then, the subjects of this study were three sections consisting of streets in Namak New Town and the results were as follows. A streetscape is necessary to have identity under the unity(context) of parts which orient to "one as a whole". However, the subject apartments were not united(contextual) in layouts, roofs, and walls, whereas their facades appeared too united(contextual). Accordingly, to make a united(contextual) streetscape, the wall located in a boundary(a buffer zone) with public space which consists of a streetscape, building layout, building height, and roof forms need a design guideline which can have unity as a whole to connect with architectural design. On the other hand, the facade which was found too uniform should have a more active design guideline to elicit identity at unity.

• Journal of Aerospace System Engineering
• /
• v.14 no.1
• /
• pp.8-15
• /
• 2020

In this paper, we propose a container wall and its boundary layer insulation design method that can maintain the temperature inside the spacecraft shipping container constantly under the condition that the heat or the external temperature changes severely to safely transport the satellite to the launch site. We will examine if the temperature inside the satellite shipping container is kept constant through the heat flow analysis and the satellite heat transfer analysis for the external environment of the satellite shipping container. Through the flow analysis inside the container, the flow distribution around the satellite in the container is analyzed, and the auxiliary fan, air conditioning system and special grill guide structure design for improving and optimizing heat flow performance are proposed.

• Korean Journal of Materials Research
• /
• v.20 no.9
• /
• pp.478-482
• /
• 2010

A series of molecular dynamic (MD), finite element (FE) and ab initio simulations are carried out to establish suitable modeling schemes for the continuum-based analysis of aluminum matrix nanocomposites reinforced with carbon nanotubes (CNTs). From a comparison of the MD with FE models and inferences based on bond structures and electron distributions, we propose that the effective thickness of a CNT wall for its continuum representation should be related to the graphitic inter-planar spacing of 3.4${\AA}$. We also show that shell element representation of a CNT structure in the FE models properly simulated the carbon-carbon covalent bonding and long-range interactions in terms of the load-displacement behaviors. Estimation of the effective interfacial elastic properties by ab initio simulations showed that the in-plane interfacial bond strength is negligibly weaker than the normal counterpart due to the nature of the weak secondary bonding at the CNT-Al interface. Therefore, we suggest that a third-phase solid element representation of the CNT-Al interface in nanocomposites is not physically meaningful and that spring or bar element representation of the weak interfacial bonding would be more appropriate as in the cases of polymer matrix counterparts. The possibility of treating the interface as a simply contacted phase boundary is also discussed.

• The Journal of Sustainable Design and Educational Environment Research
• /
• v.12 no.2
• /
• pp.43-52
• /
• 2013

This study aims to theoretically examine the educational and living elements that are needed for social education in the school system and suggest an approach to apply this result to the environmental aspects of the space in schools. To do this, characteristics of space in exemplary middle school oversee were analyzed. Also, the characteristics and status of the school space environment that foster socialization were examined. In order to increase students' social skills, the following community space should be considered. 1) teaching and learning spaces facilitating a variety of teaching methods, such as lecture, discussion, seminar classes, 2) open-spaces for communication among students, such as home base, hall, library, museum, and restaurant, 3) open-spaces for STEM education, 4) transparent windows located in the boundary wall between classrooms and hallways, 5) a large performance stage for presentation of student activities and experiences, 6) smart-learning spaces for fluent ICT system in classes and in public spaces, 7) restaurants and libraries located in the middle space of the school, and 8) ecological environments for student learning.