• Journal of the Korean Society of Visualization
• /
• v.21 no.3
• /
• pp.39-48
• /
• 2023

In this study, we investigate the effects of slots installed on the tip of a rotor blade on aerodynamic characteristics. The slots weaken the strength and spatial coherence of the tip vortex at early vortex age and accelerate the dissipation of the generated tip vortex. Accordingly, the turbulence intensity of the rotor wake is reduced at both near and far wake, which leads to a reduction in broadband noise. Tonal noise is also reduced by mitigation of tip vortices, but tonal noise reduction is limited to a narrower range of azimuths than broadband noise due to the extinction of tip vortices. In addition, slots reduce both mean thrust and thrust fluctuations. Reduction in thrust fluctuations leads to a reduction in blade loading noise, resulting in a reduction in tonal noise.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.109-110
• /
• 2012

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09a
• /
• pp.188-188
• /
• 2005

• 한국초전도학회:학술대회논문집
• /
• 2009.07a
• /
• pp.80-80
• /
• 2009

• 한국초전도학회:학술대회논문집
• /
• 2008.08a
• /
• pp.58-58
• /
• 2008

• Proceedings of the Korean Magnestics Society Conference
• /
• 2011.12a
• /
• pp.79-80
• /
• 2011

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.2
• /
• pp.298-305
• /
• 2000

The flow characteristics and the heat transfer rate on a surface by interaction of a pair of vortices were studied experimentally. The test facility consisted of a boundary-layer wind tunnel with a vortex introduced into the flow by half-delta wings protruding from the surface. In order to control the strength of the longitudinal vortices, the angles of attack of the vortex generators were varied from - 20 degree to - 45 degree, but spacings between the vortex generators were fixed to 4 cm. The 3-dimensional mean velocity measurements were made using a five-hole pressure probe. Heat transfer measurements were made using the thermochromatic liquid to provide the local distribution of the heat transfer coefficient. Unlike common flow down, common flow up vortices moved toward the centerline as they developed and interacted strongly with each other but not with the boundary layer. Spanwise profiles of Stanton number were similar for ${\beta}=-20^{\circ}\;and\;-35^{\circ}$, but not similar for ${\beta}=-45^{\circ}$. The case of ${\beta}=-20^{\circ}\;and\;-35^{\circ}$ showed the two peak Stanton number, but the case of ${\beta}=-45^{\circ}$ showed the only one peak Stanton number.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.11
• /
• pp.1618-1629
• /
• 2003

The effects of the interaction between flow field and heat transfer caused by the longitudinal vortices are experimentally investigated using a five hole probe and a transient liquid crystal technique. The test facility consists of a wind tunnel with vortex generators protruding from a bottom surface and a mesh heater. In order to control the strength of the longitudinal vortices, the angle of attack of vortex generators used in the present experiment is 20$^{\circ}$, and the spacing between the vortex generators is 25mm. The height and cord length of the vortex generator is 20mm and 50mm, respectively. Three-component mean velocity measurements are made using a f-hole probe system, and the surface temperature distribution is measured by the hue capturing method using a transient liquid crystal technique. The transient liquid crystal technique in measuring heat transfer has become one of the most effective ways in determining the full surface distributions of heat transfer coefficients. The key point of this technique is to convert the inlet flow temperature into an exponential temperature profile using the mesh heater set up in the wind tunnel. The conclusions obtained in the present experiment are as follows: The two maximum heat transfer values exist over the whole domain, and as the longitudinal vortices move to the farther downstream region, these peak values show the decreasing trends. These trends are also observed in the experimental results of other researchers to have used the uniform heat flux method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.7
• /
• pp.709-715
• /
• 2011

In order to observe the wake interaction between tip vortices generated by a two-bladed rotor with slightly different pitch angles, the velocity components of the tip vortices were measured by using a two-dimensional LDV system. It was observed that the swirl velocity components of the ensuing blade deviated from the Vatistas' n = 2 vortex model and the axial velocity components of the preceding blade deviated from the Gaussian profile. It was also found that in the wake-age range of $200^{\circ}$ to $240^{\circ}$, the filament of the ensuing blade tip vortex was stretched as result of the closing in of two vortices. The results from these observations suggest the possibility that a similar wake interaction is generated in actual rotor blades, especially, in the ones with articulated hubs.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.6
• /
• pp.1-7
• /
• 2003

In this study, steady/unsteady aerodynamic characteristic for three dimensional symmetric wing was investigated numerically using Vortex Panel Method. This program utilized linearly varying vortices in x and y directions distributed on the wing surface and was applied to the incompressible potential. flow around a three dimensional wing Separation and deformation of the wake are not considered. The comparison between NACA Airfoil Data and the computed results showed excellent agreement. πus method was applied to unsteady wings undergoing both sudden pitch-up and constant rate pitching motion. In the unsteady flow analysis, a formation and a time-dependent locations of Starting Vortices are considered and the effect of Starting Vortices on aerodynamic characteristic of the wing was calculated. The present method can be extended to apply for more complicated cases such as pitching, flapping and rotating wing analysis.