• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.3
• /
• pp.192-200
• /
• 2002

There is a volume change between the sediments and the dredged materials because the dredged materials is fully disturbed by the dredger and settled in the basin from the stabilized condition. The volume of the dredged materials is also affected by the coagulants and flocculants (hereafter C & F) which was used to speed up the settling of the suspended solids. In this study, the volume change of the dredged materials is analysed in detail due to the injection amount of the C & F. The dredged materials were sampled in the lagoon located in the East coastal zone, and the volume change of the samples is quantitatively analysed by the laboratory test due to the change of the clay content and the amount of the C & F. The optimal amounts of the C & F is determined by showing the minimal volume change due to C & F injection. From the experimental results, the volume of the dredged materials is increased 1.68 times on an average and the volume change rate is slightly increased, i.e., negligible, as the clay content increase in the case of the C & F injection.

• KIEAE Journal
• /
• v.15 no.4
• /
• pp.45-52
• /
• 2015

Purpose: Foam concrete is the concrete that contains large amount of air voids inside. In general, the density of foam concrete depends on parameters like water/binder ratio, foam volume, aggregate and pozzolan content, etc. Method: In this study, the effect of foam volume and fly ash content on dry density is investigated intensively in order to find the relationship between each parameter and their abilities to counteract with each other. According to the above information, though there are quite a number of studies on the effect micro fiber on foam concrete at low volume fractions, there is still lack of information especially on the high fiber content side. The objective of the second study is to investigate further on the use of micro fiber at higher volume fraction and fill in the lacking information. Beside from this study, the investigation of the effect of micro-fiber (polypropylene) to enhance the properties of foam concrete is also carried out. Result: Of the two variables that are investigated in this study, the foam volume and the fly ash content, show significant effect on the properties of foam concrete. The foam volume tends to decrease the density and strength of foam concrete. In the second part of our study, a large fibre volume fraction is proved to be able to evidently increase the flexural strength of foam concrete up to about 40% due to the effect of fibre bridging over the crack and a significant number of fibres that intercepts the crack surfaces. However, the compressive strength is found to decrease severely due to the occurrence of large pores as the result of fibre being added into concrete mixture.

• Radiation Oncology Journal
• /
• v.9 no.1
• /
• pp.165-170
• /
• 1991

In breast cancer, the treatment volume presents a relatively complex three dimensional structure. Effective radiation therapy requires the delivery of adequate dose to a large target volume using complex beam arrangements. The technique proposed here is our department's method using asymmetric jaw with appropriate couch, collimator and gantry rotation. This technique has the following advantages: 1) all treatments are given in a single clinical set up 2) it does not require half beam blocks 3) it produces exact geomatric match 4) it is very convenient and easy to use 5) it has daily reproducibility.

• Journal of Korean Neurosurgical Society
• /
• v.63 no.2
• /
• pp.228-236
• /
• 2020

Objective : It can be assumed that the progression of scoliosis in the juvenile period will increase the asymmetry in the rib cage, and thus will contribute to an increase in the breast asymmetry (BA) in the future. We are looking for answers to the questions; "How will the breasts look with respect to each other and what is the possibility of developing BA in the early follow-up period following the early surgical treatment and final fusion surgery of juvenile idiopathic scoliosis (JIS)?" For this reason, in this study, we aimed to evaluate the breast asymmetries of patients in the period after the final fusion. Methods : Following growing rod treatment, final fusion was achieved in 12 females with JIS. We used the anthropomorphic measurement of the modified BREAST-V formula to assess whether there was an asymmetry between the breasts after an average of 4.8 years (2-11) following final fusion. Results : In comparison, the mean volume of the left breast (222.4 mL [range, 104.1-330.2]) was larger than the mean volume of the right breast volume (214.5 mL [range, 95.2-326.7]) (p=0.034). The left breast was larger in 75% of the patients. BA was observed in 50% of the patients. No correlation was detected between the Cobb angle of the patient after final fusion and BA (p=0.688). Conclusion : In the late follow-up period, BA was detected in 50% of the patients with JIS who achieved final fusion after treatment with growing rod. In majority of the patients, left breast was larger. The patients with JIS and their families can be informed prior to the operation about the probability of BA seen in the follow-up period after fusion.

• Tribology and Lubricants
• /
• v.31 no.3
• /
• pp.125-140
• /
• 2015

In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.

• Archives of Craniofacial Surgery
• /
• v.24 no.2
• /
• pp.59-65
• /
• 2023

Background: Fibrous dysplasia (FD) is a localized bone disorder in which fibro-osseous tissue replaces the normal bone structure. Patients with craniofacial FD often present with gradual swelling, deformity, and compromised vision or hearing. We previously introduced "the core extirpation method," a novel surgical technique that is minimally invasive like traditional bone shaving but has longer-lasting effects. This study presents the long-term outcomes of our core extirpation method. Methods: We conducted a retrospective analysis of patients who underwent core extirpation for FD of the zygomaticomaxillary region from 2012 through 2021. Computed tomography (CT) scans were performed 6 to 12 months before the operation, immediately before and after the operation, and during follow-up visits. We performed all operations using the upper gingivobuccal approach, and we extirpated the core of the lesion while preserving the cortical structures of the zygoma and the maxilla to maintain symmetrical facial contour. Results: In 12 patients with lesions in the growth phase, anteroposterior/mediolateral (AP/ML) length discrepancies and the volume increased between preoperative and immediate postoperative CT scans. All patients' immediate postoperative AP/ML discrepancies were stable up to 12-17 months postoperatively. Postoperative volume showed continuous lesion growth; the median volume growth rate was 0.61 cc per month. Conclusion: In this article, we present our experiences managing FD using the minimally invasive core extirpation technique, which entails small expected blood loss and can be performed as day surgery. It provides similar cosmetic outcomes as traditional bone shaving but with longer-lasting results. Although there are some limitations with the study's retrospective nature and small sample size, our 4-year follow-up results show promising results of the core extirpation method in well-indicated patients.

• Asian Journal of Innovation and Policy
• /
• v.3 no.2
• /
• pp.216-244
• /
• 2014

This paper empirically establishes the role played by the ecosystem related parameters in the emergence and growth of high technology start-up clusters in India. It is mainly based on secondary data from six major start-up hubs in India during the period 2005-2013. Our results throw up several interesting findings. First of all, we find that traditional infrastructure related factors or robust macroeconomic situation in general are not the most important drivers. What really seem to matter are the specific start-up ecosystem related factors - such as the Internet penetration, volume of deal flow, availability of VC funding and a pre-existing critical mass of relevant high technology businesses and skill-sets. Above all, our study points out that high economic growth alone will not automatically lead to spillovers in the form of a vibrant start-up ecosystem. Rather it has to be a product of conscious and concerted policy efforts at all levels that directly address the main challenges faced by the early-stage start-ups.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.45-53
• /
• 2004

An experimental study was carried out to obtain the fundamental data about the effects of radicals induced injection on premixture combustion. A constant volume combustor divided to the sub-chamber and the main chamber was used. The volume of the sub-chamber is set up to occupy less than 1.5％ of that of whole combustion chamber. Radial twelve narrow passage holes are arranged between the main chamber and the sub-chamber. The products including radicals generated by spark ignition in the sub-chamber will derive the simultaneous multi-point ignition in the main chamber. While the equivalence ratio of pre-mixture in the main chamber and the sub-chamber is uniform. We have examined the effects of the sub-chamber volume, the diameter of passage hole, and the equivalence ratio on the combustion characteristics by means of burning pressure measurement and flame visualization. In the case of radical ignition method(RI), the overall turning time including the ignition delay became very short and the maximum burning pressure was slightly increased in comparison with those of the conventional spark ignition method(SI), that is, single chamber combustion without the sub-chamber. The combustible lean limit by RI method is extended to more ER=0.25 than that by SI method. Therefore the decrease of every emission including NOx and the improvement of fuel consumption is anticipated due to lean burn.

• Journal of the Korean School Mathematics Society
• /
• v.11 no.1
• /
• pp.19-30
• /
• 2008

Cavalieri is chiefly remembered for his work on the problem "indivisibles." Building on the work of Archimedes, he investigated the method of construction by which areas and volumes of curved figures could be found. Cavalieri regarded an area as made up of an indefinite number of parallel line segments and a volume of an indefinite number of parallel plane areas. He called these elements the indivisibles of area and volume. Cavalieri developed a method of the indivisibles which he used to determine areas and volumes. We call this Cavalieri's principle which states that there exists a plane such that any plane parallel to it intersects equal areas In both objects, then the volumes of the two objects are equal. Cavalieri's principle and method of the indivisibles are very important to understand of volume of a pyramid for gifted students.

• Journal of the Korea Computer Graphics Society
• /
• v.8 no.2
• /
• pp.23-29
• /
• 2002

In this paper, we describe an implementation technique that extends the classification and shading capabilities offered by previously reported hardware-assisted volume rendering algorithms. In designing our rendering scheme, we exploited the programmable shader technology supported by the latest consumer PC graphics hardware. Our direct volume rendering technique enables to simultaneously display up to four materials, and to dynamically control gradient magnitude to emphasize or de-emphasize surface boundaries. It can easily create lighting effects such as light source attenuation, depth cueing, and multiple light sources that were often difficult to realize in previous hardware-assisted volume rendering.