• Korean Journal of Food Science and Technology
• /
• v.31 no.2
• /
• pp.465-474
• /
• 1999

RNase activity of Saccharomyces cerevisiae ATCC 7754 was investigated to obtain strains with high ribonucleic acid (RNA) content. The yeast strain contained two RNase activities; an acidic RNase with a optima of pH $3{\sim}4$ and an alkaline RNase with a optima pH 9. The acidic RNase activity was inhibited by $0.08\;M\;HgCl_{2}$ most drastically. The alkaline RNase activity was inhibited by 2.0 M NaCl or KCl, while enhanced by addition of $0.05\;M\;CaCl_{2},\;0.02\;M\;ZnSO_{4},\;or\;0.008\;M\;HgCl_{2}$. Various mutants of Saccharomyces cerevisiae ATCC 7754 were isolated by ethylmethane sulfonate (EMS) treatment or $\gamma$-ray/ultra violet irradiation. Among the mutants that were sensitive to high concentration of KCl which inhibits alkaline RNase, B24 was selected for high RNA content per culture volume. Growth characteristics of the mutant were comparable to those of the mother strain with optimum growth at pH $4.5{\sim}5.5$. The mutant accumulated higher content of RNA than the mother strain when glucose was used as the carbon source. However, both growth rate and total RNA content of the mutant were higher in molasses medium than in glucose medium. RNA content of the mutant increased rapidly during the early stage of growth, and then decreased gradually until the culture reached stationary phase by a fed-batch culture in a 5 L jar fermenter. Maximal cell harvest and the final RNA content using the mutant B24 were 69.6 g/L culture broth and 19.8 g/100 g of the dry cell while those using the mother strain were 68 g/L culture broth and 16.1 g/100 g of dry cell, respectively.

• Restorative Dentistry and Endodontics
• /
• v.34 no.5
• /
• pp.450-459
• /
• 2009

The aim of this study was to measure the initial dynamic modulus changes of light cured composites using a custom made rheometer. The custom made rheometer consisted of 3 parts: (1) a measurement unit of parallel plates made of glass rods, (2) an oscillating shear strain generator with a DC motor and a crank mechanism, (3) a stress measurement device using an electromagnetic torque sensor. This instrument could measure a maximum torque of 2Ncm, and the switch of the light-curing unit was synchronized with the rheometer. Six commercial composite resins [Z-100 (Z1), Z-250 (Z2), Z-350 (Z3), DenFil (DF), Tetric Ceram (TC), and Clearfil AP-X (CF)] were investigated. A dynamic oscillating shear test was undertaken with the rheometer. A certain volume ($14.2\;mm^3$) of composite was loaded between the parallel plates, which were made of glass rods (3 mm in diameter). An oscillating shear strain with a frequency of 6 Hz and amplitude of 0.00579 rad was applied to the specimen and the resultant stress was measured. Data acquisition started simultaneously with light curing, and the changes in visco-elasticity of composites were recorded for 10 seconds. The measurements were repeated 5 times for each composite at $25{\pm}0.5^{\circ}C$. Complex shear modulus G*, storage shear modulus G', loss shear modulus G" were calculated from the measured strain-stress curves. Time to reach the complex modulus G* of 10 MPa was determined. The G* and time to reach the G* of 10 MPa of composites were analyzed with One-way ANOVA and Tukey's test ($\alpha$ = 0.05). The results were as follows. 1. The custom made rheometer in this study reliably measured the initial visco-elastic modulus changes of composites during 10 seconds of light curing. 2. In all composites, the development of complex shear modulus G* had a latent period for $1{\sim}2$ seconds immediately after the start of light curing, and then increased rapidly during 10 seconds. 3. In all composites, the storage shear modulus G" increased steeper than the loss shear modulus G" during 10 seconds of light curing. 4. The complex shear modulus of Z1 was the highest, followed by CF, Z2, Z3, TC and DF the lowest. 5. Z1 was the fastest and DF was the slowest in the time to reach the complex shear modulus of 10 MPa.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.100-107
• /
• 2018

The material and geometrical nonlinear finite elment analysis of UHPFRC 50M composite box girder was carried out. Constitute law in tension and compressive region of UHPFRC and HPC were modeled based on specimen test. The accuracy of nonlinear FEM analysis was verified by the experimental result of UHPFRC 50M composite girder. The UHPFRC 50M segmental composite box girder which has 1.5% steel fiber of volume fraction, 135MPa compressive strength and 18MPa tensile strength was tested. The post-tensioned UHPFRC composite girder consisted of three segment UHPFRC U-girder and High Strength Concrete reinforced slab. The parts of UHPFRC girder were modeled by 8nodes hexahedron elements and reinforcement bars and tendons were built by 2nodes linear elements by Midas FEA software. The constitutive laws of concrete materials were selected Multi-linear model both of tension and compression function under total strain crack model, which was included in classifying of smeared crack model. The nonlinearity of reinforcement elements and tendon was simulated by Von Mises criteria. The nonlinear static analysis was applied by incremental-iteration method with convergence criteria of Newton-Raphson. The validation of numerical analysis was verified by comparison with experimental result and numerical analysis result of load-deflection response, neutral axis coordinate change, and cracking pattern of girder. The load-deflection response was fitted very well with comparison to the experimental result. The finite element analysis is seen to satisfactorily predict flexural behavioral responses of post-tensioned, reinforced UHPFRC composite box girder.

• Microbiology and Biotechnology Letters
• /
• v.17 no.1
• /
• pp.1-7
• /
• 1989

To enhance the capability of starch fermentation of the transformant TSD-14, the heat treated protoplasts of TSD-14 were fused with the protoplasts of C. tropicalis (lys$^-$) in the presence of 30% (w/ v) PEG and 20 mM CaC1$_2$. Fusants were selected by nutritional complementation on minium medium and the fusion frequency was 4.4$\times$10$^{-5}$. All fusants tested were possessed of complemented traits concerning carbon compound assimilation, and the cell volumes of the fusants were approximately 1.5 times larger than the parental strains. The fusants were genetically very stable, and were able to hydrolyze alpha 1,4-glucosidic linkage as well as alpha 1,6-linkage of starch contrary to one of parents TSD-14, The most promising fusant FSC-14-75 produced 8.7% (v/v) of ethanol from 15% liquefied potato starch medium, but the result was enhanced to 9.3% (v/v) by addition of 0.3% peptone. The corresponding fermentation efficiency was 86.0%.

• Korean Journal of Agricultural Science
• /
• v.11 no.2
• /
• pp.322-327
• /
• 1984

As a basic studies for the laboratory scale production of alfalfa inoculum, Rhizobium meliloti M14 was characterized for its carbon and nitrogen sources, and some parameters for broth cultivation in a chemostat were studied by semi-continuous operation. The result s obtained were as follows. 1. Growth rate of the strain was increased by disaccharides than by monosaccharides tested, and pentoses resulted in poor growth than hexoses. Sugar alcohols including inositol supported the best growth among sugars. 2. Mannitol in the yeast-mannitol-broth was substituted by natural carbon sources such as malt extract or molasses. 3. Ten per cent of fresh yeast water appeared to supply enough amount of growth factor s for the strain, and the effect was equivalent to 0.24 percent of the commercial yeast extract powder. 4. Batch growth of the stain in a chemostat, New Brunswick Micro Ferm 28L, reached in the early stationary growth phase of $5{\sim}7{\times}10^9cells/ml$ after 36 hours of incubation. The culture at this stage was switched to semi-continuous cultivation, and the culture broth of four-fifth of the working volume was recovered every 24 hours when the maximal count was obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.2
• /
• pp.187-194
• /
• 2012

The strength of particle-reinforced metal matrix composites is, in general, known to be increased by the geometrically necessary dislocations punched around a particle that form during cooling after consolidation because of coefficient of thermal expansion (CTE) mismatch between the particle and the matrix. An additional strength increase may also be observed, since another type of geometrically necessary dislocation can be formed during extensive deformation as a result of the strain gradient plasticity due to the elastic-plastic mismatch between the particle and the matrix. In this paper, the magnitudes of these two types of dislocations are calculated based on the dislocation plasticity. The dislocations are then converted to the respective strengths and allocated hierarchically to the matrix around the particle in the axisymmetric finite-element unit cell model. The proposed method is shown to be very effective by performing finite-element strength analysis of $SiC_p$/Al2124-T4 composites that included ductile failure in the matrix and particlematrix decohesion. The predicted results for different particle sizes and volume fractions show that the length scale effect of the particle size obviously affects the strength and failure behavior of the particle-reinforced metal matrix composites.

• Journal of Biomedical Engineering Research
• /
• v.37 no.2
• /
• pp.90-103
• /
• 2016

This research was aimed to analyze load sharing ratios between cortical shell and trabecular bone of a degraded lumbar vertebra with aging, and also evaluate elastic moduli assigned into an FE model, using finite element method. For the better analysis of trabecular bone, effective elastic moduli, that is, nominal elastic moduli divided by the volumetric porosities was used. The elastic moduli of the cortical shell suitable for the trabecular bone were obtained from the equations on the basis of idealized stress-strain relations, including areal porosities. To minimize numerical errors, p-element was used. Using eight parameters that refer to some published papers, the geometry of L3 with a removed posterior part. After the constant compressive displacement was applied, the load sharing ratios were obtained by using both every elastic strain energy and every vertical force between two bones in each 8-volume. As results, 1) according to an increase in age from 20-year to 80-year, load sharing ratios of trabecular bone decreased from 55% to 49%; 2) the maximal ratios of each bone were occurred in the mid-plane of centrums and the endplate of cortical shells, respectively; 3) effective elastic moduli assigned into a porous centrum/cortex were found to be adequate; 4) for load sharing ratios, the difference of two methods showed that the total ratios were almost same within less than 1% but the partial ratios at every depth were more or less different each other.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.5947-5955
• /
• 2013

This study was intended to estimate the axial deformation of joint between pavement modules in the rapid-constructible modular pavement system, and to investigate the applicability of two-phase composites for a joint material, which was composed of cement paste, epoxy, or polyurethane as a matrix and sand as particles. A case which had supports under the pavement module as well as a case which the module was put on roadbed directly were considered in FEM analysis for the axial deformation. The effect of self-weight, live load, thermal change, and drying shrinkage were estimated and the thermal change was found to cause the largest deformation compared to the others. Deformation capacity of two-phase composites was predicted using the modified shear-lag model. In the analytical results for the elastic modulus and maximum tensile strain with different volume fractions of sand, 20~30 % replacement of sand was revealed to satisfy the required strain capacity with economy when if the width of joint was designed to be 15~20 mm.

• Parasites, Hosts and Diseases
• /
• v.23 no.2
• /
• pp.293-299
• /
• 1985

This study is to verify the protective ability against experimental Naegleria meningoencephalitis by immunization with Naegleria fowleri in mice. Naegleria fewleri, strain 0359, and Naegleria gruberi, strain EGB, were used in this study, and cultured in CGVS medium akenically. Inbred BALB/C mice, weighing about 20g, were immunized by three intraperitoneal injection of $1{\times}10^6$ N. fowleri trophozoites at the interval of one week. This N. fowleri trophozoites antigen was fixed with 5% formaldehyde. N. fowleri trophozoites from culture were homogenized with soiicator at $4^{\circ}C$ as monitored by phase contrast microscopy, and their membrane and cell content preparations were made for the immunization of mice. Their inoculation dose in volume was equivalent to the $1{\times}10^6$ trophozoites in each injection for immunization. And N. gruberi trophosoites, whieh was fixed with 5% formaldehyde, were also used for immunisation. Mice were inoculated intranasally with $5{\times}10^4$ N. fowleri trophozoites in a 511 suspension under anesthesia by as intraperitoneal injection of about 1 mg secobarbiturate. Nervousness, rotation or sluggish behaviour were observed in the mice which were infected with N. fewleri. Necrotic lesion was demonstrated in the anterior portion of brain, especially in the olfactory lobe. The inflammatory cell infiltration with numerous H. fowleri trophozoites was noticed. This pathological changes were more extensive in the control than in the experimental groups. Mice were dead due to experimental primary amoebic meningoencephalitis that developed between 8 days and 23 days after inoculation. Mortality rate of the mice was low in the immunized experimental group. Mean survival time, which is the survival duration of mice from the infection to death, was prolonged significantly in the immunized mice except in the mice immunized with JV, fowleri membrane. Even in the mice immunized with N. gruberi, survival time was delayed. In summary, the effectiveness of immunization is demonstrated in terms of protective immunity against Naegleria meningoencephalitis in mice.

• Korean Journal of Microbiology
• /
• v.28 no.1
• /
• pp.55-64
• /
• 1990

Cell volume and DNA contents of the fusants were similar to those of parents. Genetic stability of the fusants was increased when they were cultured on minimal medium (MM) rather than on complete medium (CM), and the fusants were stabilized by subculturing 7 generations each 7 day on MM agar. The finally selected fusants after being cultured for 6 months on CM were stable without segregation. The fusants could also form nuclein and ascospores, and show red and pink colors by the test of TTC colorization. Assimilability and fermentability of carbon sources of the fusants were similarto those of parents. The tolerance of KCl, NaCl, sodium propionate and cycloheximide showed the traits of one strain of parents. When the fusants were cultured for 72 hr and 60 hr in the medium containing 20% glucose and sucrose, respectively, the yield of ethanol for FWKS 260 was reached to 9.6 v/v% and 9.8v/v%, respectively. The sensitive strain Kyokai 7 was found to be killed entirely after cultivation of 48 hr by the killer toxin from the fusants. The recipient S 29 and Kyokai 7 were found to have neither L nor M dsRNA plasmid. However, K 52 and fusants had both L and M dsRNA plasmid of 4.7 kb and 2.5 kb, respectively. The curants treated by heat and cycloheximide did not contain M dsRNA plasmid, but had large amounts of L dsRNA plasmid of those of killer yeasts.