• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.81-84
• /
• 1998

New diagnostic techniques have been tried on the applications of chemical, physical and micro-structural methods because there was a limit to diagnose degradation in Korean Underground Residential Distribution (URD) power cables with the conventional electrical methods. In this study, non-electrical properties were carried out as such. Characterization of interface layer was analyzed by X-ray, characterization of insulator by water tree, degree of crosslinking, shrinkage as well as ${\mu}$ -FTIR, characterization of semiconductive layer by volume resistivity. Electrical properties were also performed by leakage current.

• 마이크로전자및패키징학회지
• /
• 제18권4호
• /
• pp.63-70
• /
• 2011

Anorthite forming glass frits in amounts up to 25 vol% of the silver powder were added to improve the adhesion between the conductor pattern formed by thick film photoimageable process and the low temperature co-fired ceramics (LTCC) substrate. The sheet resistance of the conductor pattern was raised from 0.13 ${\Omega}/{\square}$ to 2.25 ${\Omega}/{\square}$ as the volume percentage of glass frit increased up to 25 vol%. The adhesion strength was improved with this glass frit increase, but it decreased when the glass content exceeded 20 vol% which are possibly attributed to the liquid pool effect and the reduced fracture toughness in the interface between conductor and LTCC layer. The shrinkage of the width of the conductor pattern decreased with the addition of glass contents.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.825-830
• /
• 1999

The purpose of this study is to improve overall performance of prefoamed lightweight cellular concrete for On-Dol system floor. This study includes 4 sections as follows. \circled1 Analysis of the structural characteristics of On-Dol System focusing on the lightweight cellular concrete insulation layer. \circled2 Establishment of the mixing design equations. \circled3 Development of some admixtures used with foaming agent. \circled4 Improvement of the equipment for onsite production. This study has proven that, compared with the current existing one, the newly developed lightweight cellular concrete has been reduced the usage of cement by 20% and the cracks caused by cement drying shrinkage up to 80% but has shown the increased compression strength by 20% at 7 days curing period. The volume contraction of freshly prepared cellular concrete by the loss of foam was hardly found in newly developed lightweight cellular concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.545-546
• /
• 2009

본 연구에서는 재활용된 polyethylene terephthalate (RPET)로 만든 플라스틱 단섬유의 구조재료로써의 사용 가능성을 조사하였다. 실험은 균열제어 성능을 확인하기 위해 구속건조수축균열 시험을 평가하였다. 성능을 검증하기 위해서 가장 널리 상용되는 합성섬유인 poly propylene (PP) 섬유와 비교하였으며, 섬유의 혼입률을 0%, 0.5%, 0.75%, 1.0%로 변화시켜 혼입률에 따른 영향을 함께 검토하였다.

• The International Journal of Costume Culture
• /
• 제5권2호
• /
• pp.53-65
• /
• 2002

Morphology of polyester fiber was physically modified by solvent treatment. PET fiber was treated with N,N-dimethylformamide (DMF) at 100, 120, $140^{circ}C$ for 10 minutes without tension. The structural changes in the morphology of DMF-induced modified PET fiber were FTIR and SEM analysis. Also dyeing behavior of DMF-treated polyester fibers with various disperse dyes was studied to detect changes of amorphous area in fine structure. DMF treatment resulted in increases in total void content, degree of crystallinity, trans isomer content, chain folding, segmental mobility and molecular packing, but it resulted in decreases in amorphous orientation, intermolecular forces and individual void size through longitudinal shrinkage, lateral welling and removal of oligomers. Void-size distribution could be estimated from the dye uptake with various sizes of disperse dyes. In contrast to the large increases in dye uptake with small dye molecules, there is no and little dye uptake with the bulkiest dye, which means that void size is bigger or smaller than the volume of each dye. Diffusion rates of dye molecules showed increases. This dyeing study revealed that the disperse dyeing is very effective method for characterizing the internal morphology of polyester fiber.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.217-222
• /
• 2003

The steel slag, a by-product which is produced during the manufacture of steel by refining pig iron, is mainly used as road materials after aging it. It is necessary to age steel slag for long time in air because the reaction with water and free-CaO in steel slag could make the expansion of volume. This problem prevents steel slag from being used as aggregate for concrete. But steel slag used in this study was controled by an air-jet method which rapidly cools substance melted at a high temperature. Rapid cooling prevents from generation of free-CaO in steel slag. In this study, properties of steel slag manufactured by air-jet method and mortar used it were investigated. As results of this study, free-CaO contents were controled under 1%. Mortar used this steel slag demanded to lower water contents, higher compressive strength and lower drying shrinkage than the basic mortar in the same condition.

• 한국세라믹학회지
• /
• 제45권12호
• /
• pp.782-787
• /
• 2008

Ni-ceria cermets have been extensively investigated as candidates for the anode in intermediate-temperature solid oxide fuel cells. We have used the citric method to synthesize nanocomposite powders consisting of NiO (Ni metal content: $40{\sim}60%$ by volume) highly dispersed in $Ce_{0.9}Gd_{0.1}O_{1.95}$ (CGO). The microstructure characteristics and sintering behaviors of the nanocomposites were investigated. No impurity phases were observed and the shrinkage of these substrates matched well with that of a CGO electrolyte with a specific surface area of $11\;m^2/g$. Densification of the CGO electrolyte layer to $<5\;{\mu}m$ thickness was achieved by co-firing the laminated electrolyte with the porous NiO-CGO substrate at $1400^{\circ}C$ for 6 h.

• 대한기계학회논문집A
• /
• 제32권5호
• /
• pp.419-423
• /
• 2008

A new polymer replication technology using ultrasonic vibration is proposed and demonstrated. A commercial ultrasonic welder has been used in this experiment. Two different types of nickel molds have been fabricated: pillar type and pore type microstructures. Polymethyl methacrlylate (PMMA) has been used as the replication material and the optimal molding time was 2 sec and 2.5 sec for pillar-type and pore-type micromolds, respectively. Compared with the conventional polymer micromolding techniques, the proposed ultrasonic micromolding technique has the shortest processing time. In addition, only contact area between micromold and polymer substrate is melted so that the thermal shrinkage can be minimized. The fabricated PMMA microstructures have been very accurately replicated without vacuum. The proposed ultrasonic molding technique is a good alternative for high volume production.

• 한국세라믹학회지
• /
• 제20권3호
• /
• pp.217-226
• /
• 1983

Adquate amount of calcia was added to the regent-grade Zirconia body. Here the amount and the form of calcia were 7-21 mol% and regent-grade calcium cabonate respectively. The specimens were fired at 175$0^{\circ}C$ for 0, 3, 5 and 7 hours respectively. The phase Strength X-ray diffraction analysis and Scaning electron microscopy. The results were as follows (1) As the additive amount of calcia was increased the firing linear shrinkage apparent density compressive strength and modulus of rupture decreased but the apparent porosity increased. (2) The specimens soaked and containing calcia displayed the grain growth. (3) Monoclinic and cubic zirconia were seen in the sepcimens containing 7 mol% calcia. When without soaking the specimens containing 7-10 mol% calcia had the volume change by monoclinic$\rightleftharpoons$tetragonal transformation. (4) The lattice parameter increased according as the calcia additive was increased. The specimens containing above 19mol% calcia had the costant lattice parameter. The value of that was from 5.1264 to 5.1396 $\AA$ in the case of 7 hours soaking.

• Nuclear Engineering and Technology
• /
• 제33권1호
• /
• pp.62-72
• /
• 2001

The one-dimensional finite element program was developed to analyze the coupled behavior of heat, moisture, and air transfer in unsaturated porous media. By using this program, the simulation results were compared with those from the laboratory infiltration tests under isothermal condition and temperature gradient condition, respectively. The discrepancy of water uptake was found in the upper region of a bentonite sample under isothermal condition between numerical simulation and laboratory experiment. This indicated that air pressure was built up in the bentonite sample which could retard the infiltration velocity of liquid. In order to consider the swelling phenomena of compacted bentonite which cause the discrepancy of the distribution of water content and temperature, swelling and shrinkage factors were incorporated into the finite element formulation. It was found that these factors could be effective to represent the moisture diffusivity and unsaturated hydraulic conductivity due to volume change of bentonite sample.