• Journal of the Korea Institute of Building Construction
• /
• v.2 no.2
• /
• pp.165-172
• /
• 2002

A reinforced concrete building neighboring in Pusan or Ulsan where is directly exposed to salt water contrasting with other in land areas contains much salt content percolated from the outside that the high salt content percolates and diffuses through the inside of reinforced concrete; therefore, an immovable tunic surrounding it begins to be destroyed and eroded with high speed. At the time, the cross-sectional area and volume expansion of re-bar reinforcing result in being cracks make a rapid progress gradually until they appear in the surface of the one, the phenomenon such as being a thin layer or falling off the part of it causes a lowering of its durability and might collapse the concrete construction. So far, we've investigated into salt content of reinforced concrete constructions neighboring in a seaside district and damage by carbonation, and we came to a conclusion as follows: $\circled1$ Under the oceanic circumstance a concrete construction is influenced by sea water directly that contains much amount of salt content contrasting with other constructions on inland areas. $\circled2$ Because of chloride penetration the carbonation of reinforced concrete made a rapid progress until more than the covering thickness of re-bar. $\circled3$ An old reinforced concrete building which has been piled up salt injury and proceeding the carbonation of its cross-sectional area. $\circled4$ According to rapidly cracking from the inside to surface of reiforced concrete, the phenomenon of being a thin layer or falling off the part of reinforced concrete results in a lowering of durability and shortening the life-time of concrete construction itself.

• Applied Chemistry for Engineering
• /
• v.26 no.1
• /
• pp.80-85
• /
• 2015

Silicon/carbon composites as anode materials for lithium-ion batteries were examined to find the cycle performance and capacity. Silicon/carbon composites were prepared by a two-step method, including the magnesiothermic reduction of SBA-15 (Santa Barbara Amorphous material No. 15) and carbonization of phenol resin. The electrochemical behaviors of lithium ion batteries were characterized by charge/discharge, cycle, cyclic voltammetry and impedance tests. The improved electrochemical performance attributed to the fact that silicon/carbon composites suppress the volume expansion of the silicon particles and enhance the conductivity of silicon/carbon composites (30 ohm) compared to that of using the pure silicon (235 ohm). The anode electrode of silicon/carbon composites showed the high capacity approaching 1,348 mAh/g and the capacity retention ratio of 76% after 50 cycles.

• Korea-Australia Rheology Journal
• /
• v.12 no.2
• /
• pp.101-105
• /
• 2000

The crystallization behavior of homo polypropylene (PP) and PP in the PP-poly($\varepsilon$-caprolactone) (PCL) blends during isothermal crystallization has been investigated using differential scanning calorimeter (DSC) and advanced rheometric expansion system (ARES). From the storage modulus data of the homo PP and PP-PCL blends during isothermal crystallization, the volume fraction of crystallized material ($X_t$) of the homo PP and PP in the PP-PCL blends was calculated using the various rheological models. The results of $X_t$ of the homo PP and PP in the PP-PCL blends from ARES measurement were compared with the results from DSC. The $X_t$ of the homo PP was found to be higher in the ARES measurement than in the DSC. The crystallization rate of the homo PP was found to be faster in the rheological measurements than in the thermal analysis. The $X_t$ of PP in the PP-PCL blends with various compositions was obtained from the thermal analysis and rheological measurements. The $X_t$ of PP in the PP-PCL blends obtained from the thermal analysis and rheological measurements are not consistent. This discrepancy of $X_t$ may be due to the morphological changes resulted from the different crystallization kinetics of PP in the PP-PCL blends.

• Tribology and Lubricants
• /
• v.36 no.4
• /
• pp.199-206
• /
• 2020

CoCr-based alloys have been developed as wear-resistant materials owing to their excellent mechanical properties and strong wear resistance. The purpose of this study is to experimentally assess the frictional and wear characteristics of CoCr-based alloys slid against two different counter materials subjected to various normal forces to determine the expansion applicability of CoCr-based alloys. CoCrMo and CoCr alloys were selected as the target materials and NiCr and NiCrB alloys as counter materials. Experimental tests were performed using a pin-on-reciprocating plate tribo-tester under dry lubrication. Before performing the tests, the surface of the specimens was observed through confocal microscopy and the hardness was measured using a micro-Vickers hardness tester. The wear volume of the plate was calculated at the end of the tests using confocal microscope data, and the wear rate was quantitatively obtained based on Archard's wear law. From the results, the wear rates of the CoCrMo specimens that slid against NiCr and NiCrB are 7.69 × 10^-6 ㎣/Nm and 5.26 × 10^-6 ㎣/Nm, respectively. The wear rates of the CoCr specimens that slid against NiCr and NiCrB were higher than those of the CoCrMo specimens by factors of approximately 4 and 8, respectively. The CoCrMo specimens further exhibited lower friction characteristics than the CoCr specimens. The findings of this study will be useful for expanded applications of CoCr-based alloys as wear-resistant materials for various mechanical parts.

• Resources Recycling
• /
• v.19 no.4
• /
• pp.51-57
• /
• 2010

As a recycling of Si sludge from Si wafer process, a Si-SiC-CuO-C composite material was synthesized and investigated as an anode material for lithium batteries. The Si sludge consisted of Si, SiC, machine oil, and metallic impurities. The oil and metal impurities was removed by organic washing, magnetic separation, and acid washing. The Si-SiC-CuO-C composite from the recovered Si-SiC mixture was prepared by high-energy mechanical milling. According to the electrochemical tests such as charge-discharge capacity and cycling behavior, it showed the improved cycle performance. The SiC and CuO-related phases were presumed to restrain the volume expansion of the anode and Fe, however, should be removed below 10 ppm prior to synthesis of the composite because it caused the capacity loss of the active material itself.

• Journal of the Korean Ceramic Society
• /
• v.30 no.4
• /
• pp.289-298
• /
• 1993

Properties in terms of the variation of the glass compositions, which were density (p), molar volume(Vm), atom/ion packing density (Dp), refractive index (nD), transformation temperature (Tg), dilatometric softening point (Td), thermal expansion coefficient (α), Young's modulus (E), and knoop hardness (KHN) were investigated in CaO-SiO2 glasses and CaO-P2O5-SiO2 glasses containing less than 10mole% of P2O5. Those properties were measured by density measurement kit, Abbe refractometer, dilatometer, ultrasonic pulse echo equipment, and micro hardness tester. When CaO content was increased in CaO-SiO2 glasses, p, Dp, nD, Tg, Td, α, E and KHN were increased, while Vm was decreased. When P2O5 was added to the CaO-SiO2 glasses with constant CaO/SiO2 ratio as 1.07, p, Dp, nD, Tg, Td, α, E and KHN were decreased, while Vm was increased. When the amount of P2O5 in glasses was kept constant, the changes of the properties with variation of CaO content in the CaO-P2O5-SiO2 glasses were very similar to those of CaO-SiO2 glasses. These phenomena could be explained by the structural role of P2O5 in the CaO-P2O5-SiO2 glasses, which was polymerization of siicate structures and resulted in [PO4] monomer structure in glasses. Due to this structural characteristics, the bond strength and packing density were changed with compositions. Proportional relationships between 1) np and Dp, 2) Tg, Td, α and CaO content, 3) E and Vm-1, and 4) KHN and P2O5 content were evaluated in this investigation.

• Journal of Energy Engineering
• /
• v.20 no.3
• /
• pp.178-184
• /
• 2011

Compressed Air Energy Storage (CAES) is a combination of energy storage and generation by storing compressed air using off-peak power for generation at times of peak demand. In general, both charging and discharging of high-pressure vessel are unsteady processes, where the pressure is varying. These varying conditions result in low efficiencies of compression and expansion. In this paper, a new constant-pressure CAES system to overcome the current problem is proposed. An energy analysis of the system based on the concept of exergy was performed to evaluate the energy density and efficiency of the system in comparison with the conventional CAES system. The new constant-pressure CAES system combined with pumped hydro storage requires the smaller cavern with only half of the storage volume for variable-pressure CAES and has a higher efficiency of system.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.9 no.3
• /
• pp.299-307
• /
• 2007

In this study, a new concept for simulating a physical damage of tunnel shotcrete lining due to a long-term chemical deterioration has been proposed. It is known that the damage takes place mainly by internal cracks, reduction of stiffness and strength, which results mainly from volume expansion of the lining and corrosion of cement materials, respectively. This damage mechanism of shotcrete lining appears similar in most kinds of chemical reactions in tunnels. Therefore, the mechanical deterioration mechanism induced by a series of chemical reactions was generalized in this study and mathematically formulated in the framework of thermodynamics. The numerical model was implemented to a 3D finite element code, which can be used to simulate behaviour of tunnel structures undergoing external loads as well as chemical deterioration in time. A number of illustrative examples were given to show a feasibility of the model in tunnel designs.

• Nutritional Sciences
• /
• v.1 no.1
• /
• pp.29-33
• /
• 1998

The present study was designed to compare the nutrient intake and iron status of athletic female students majoring in aerobics (n=18) to those of age-matched(20-22 yr) sedentary controls (n=19). The athletic students were exercising regularly for 9.1$\pm$1.4 hrs/wk and the mean training period of aerobics was 2.9$\pm$0.2 years. Means of height, weight, and body mass index calculated as the Quetlet index were similar between athletic and sedentary students. However, mean body fat % of the athletic students (22.3$\pm$1.0%) was significantly lower than that of the sedentary controls (25.8$\pm$0.6%), indicating the effects of routine exercise. Mean daily iron intake was not significantly different between groups (9.9$\pm$0.7 mg vs. 10.9$\pm$0.8 mg), but much lower than the Korean RDA (18 mg/d) in both groups. Dietary calcium intake of the athletic students was significantly lower than that of the sedentary controls. Hematocrit (Hct) and hemoglobin (Hb) values were significantly lower in the athletic students than in the sedentary students (Hct : 40.0$\pm$0.7% vs. 43.8$\pm$0.5% ; Hb : 12.6$\pm$0.3g/dl vs. 14.8$\pm$0.3 g/dl). However, other iron status values such as serum iron, TIBC, and transferrin saturation were not significantly different between groups. Therefore, the low hemoglobin levels in the athletic group are probably due to plasma dilution in endurance-trained individuals. Serum ferritin level was a little lower in the athletic group, but no significant difference between groups was found. Serum triglyceride concentration in the athletic students was significantly lower than that in the control students. In conclusion the findings suggest that regular training of female athletes majoring in aerobics is associated with an increased risk of pseudoanemia due to plasma volume expansion and a decreased risk of coronary heart disease by decreasing body fat and blood lipid level.

• Journal of Korean Neurosurgical Society
• /
• v.42 no.5
• /
• pp.377-381
• /
• 2007

Objective : High-molecular-weight hydroxyethyl starch (HES) compromises blood coagulation more than does low-molecular-weight HES. We compared the effects of low- and high-molecular-weight HES for the treatment of vasospasm and investigated the dose relationship with each other. Methods : Retrospectively, in a series of consecutive 102 patients with subarachnoid hemorrhage (SAH), 35 patients developed clinical symptoms of vasospasm of these fourteen patients were treated with low-molecular weight HES for volume expansion while the other 21 received high-molecular-weight HES as continuous intravenous infusion. Prothrombin time (PT), partial thromboplastin time (PIT), fibrinogen level, and platelet count were all measured prior to initiation, during treatment and after termination of therapy for symptomatic vasospasm. The total dose of HES ranged from 5 L to 14 L and median infusion duration was 10 days. Results : A more pronounced PTT prolongation was observed in high-molecular-weight HES group compared with low-molecular-weight HES group. No other coagulation parameters were altered. Dosage (=duration) shows a positive correlation with PTT. Clinically, significant bleeding episodes were noted in four patients who received high-molecular-weight HES. Conclusion : Coagulopathy was developed in direct proportion to molecular weight of starch and dosages. We propose the extreme caution in the administration of HES solution for the vasospasm treatment.