• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.663-666
• /
• 2005

Gas hydrates are ice-like compounds that form at the low temperature and high pressure conditions common in shallow marine sediments at water depths greater than 300-500 m when concentrations of methane and other hydrocarbon gases exceed saturation. Estimates of the total mass of methane carbon that resides in this reservoir vary widely. While there is general agreement that gas hydrate is a significant component of the global near-surface carbon budget, there is considerable controversy about whether it has the potential to be a major source of fossil fuel in the future and whether periods of global climate change in the past can be attributed to destabilization of this reservoir. Also essentially unknown is the interaction between gas hydrate and the subsurface biosphere. ODP Leg 204 was designed to address these questions by determining the distribution, amount and rate of formation of gas hydrate within an accretionary ridge and adjacent basin and the sources of gas for forming hydrate. Additional objectives included identification of geologic proxies for past gas hydrate occurrence and calibration of remote sensing techniques to quantify the in situ amount of gas hydrate that can be used to improve estimates where no boreholes exist. Leg 204 also provided an opportunity to test several new techniques for sampling, preserving and measuring gas hydrates. During ODP Leg 204, nine sites were drilled and cored on southern Hydrate Ridge, a topographic high in the accretionary complex of the Cascadia subduction zone, located approximately 80km west of Newport, Oregon. Previous studies of southern Hydrate Ridge had documented the presence of seafloor gas vents, outcrops of massive gas hydrate, and a pinnacle' of authigenic carbonate near the summit. Deep-towed sidescan data show an approximately $300\times500m$ area of relatively high acoustic backscatter that indicates the extent of seafloor venting. Elsewhere on southern Hydrate Ridge, the seafloor is covered with low reflectivity sediment, but the presence of a regional bottom-simulating seismic reflection (BSR) suggests that gas hydrate is widespread. The sites that were drilled and cored during ODP Leg 204 can be grouped into three end-member environments basedon the seismic data. Sites 1244 through 1247 characterize the flanks of southern Hydrate Ridge. Sites 1248-1250 characterize the summit in the region of active seafloor venting. Sites 1251 and 1252 characterize the slope basin east of Hydrate Ridge, which is a region of rapid sedimentation, in contrast to the erosional environment of Hydrate Ridge. Site 1252 was located on the flank of a secondary anticline and is the only site where no BSR is observed.

• Journal of the Korean Institute of Gas
• /
• v.16 no.4
• /
• pp.38-43
• /
• 2012

The purpose of this study is to carry out the consequence analysis of an accident related to the release of Hydrogen chloride occurred in a petrochemical company in Korea and suggest the measures to prevent similar accidents from happening again. The total amount released through the safety valve of HCl Column was calculated based on the rated capacity of the safety valve, the ideal gas equation and mechanical energy balance, respectively. As a result of the calculation, we found that the amount of HCl released through the safety valve was at least 76.8 kg. Also, we predicted the dispersion concentration at the position of the injured workers(more than 350 m away from the accident location) using simulation programs such as PHAST. The results of ALOHA and K-CARM are 304 ppm and 1,700 ppm respectively. However, PHAST calculation indicated that the concentration is less than l ppm. From these results, we can understand that workers were injured by HCl gas released from the safe valve and the concentration of gas might be less than 1 ppm. Also, it is important for toxic gases such as HCl to be vented safely to the atmosphere after scrubbing.

• Korean Journal of Childcare and Education
• /
• v.9 no.2
• /
• pp.215-238
• /
• 2013

This study examined the effects of mothers' rejective parenting, emotional expressivity, children's emotional regulation strategy on their social withdrawal. Participants were 223 children(121 boys, 102 girls; recruited from classes with 4-5 year olds), their mothers and 20 child care teachers. The teachers completed rating scales to measure the children's social withdrawal and emotional regulation strategies. Mothers reported their rejective parenting along with emotional expressivity. The collected data were analyzed using descriptive statistics, Pearson's productive correlation coefficient, and hierarchical multiple regressions. Results showed that mothers' rejective parenting, children's venting/support seeking strategy and avoidance/non-responsive strategy had positive relation to, whereas mother's positive expressivity were negatively related to their social withdrawal. Hierarchical regression analysis indicated that the interaction of mother's rejective parenting and positive expressivity predicted children's social withdrawal. Mother's rejective parenting was associated with children's social withdrawal, especially for children with the lowest level of mother's positive expressivity. In addition, the association between mother's rejective parenting and children's social withdrawal were partially mediated by their venting/support seeking strategy.

• Nuclear Engineering and Technology
• /
• v.50 no.5
• /
• pp.665-672
• /
• 2018

A venturi scrubber is an important element of Filtered Containment Venting System (FCVS) for the removal of aerosols in contaminated air. The present work involves computational fluid dynamics (CFD) study of dust particle removal efficiency of a venturi scrubber operating in self-priming mode using ANSYS CFX. Titanium oxide ($TiO_2$) particles having sizes of 1 micron have been taken as dust particles. CFD methodology to simulate the venturi scrubber has been first developed. The cascade atomization and breakup (CAB) model has been used to predict deformation of water droplets, whereas the Eulerian-Lagrangian approach has been used to handle multiphase flow involving air, dust, and water. The developed methodology has been applied to simulate venturi scrubber geometry taken from the literature. Dust particle removal efficiency has been calculated for forced feed operation of venturi scrubber and found to be in good agreement with the results available in the literature. In the second part, venturi scrubber along with a tank has been modeled in CFX, and transient simulations have been performed to study self-priming phenomenon. Self-priming has been observed by plotting the velocity vector fields of water. Suction of water in the venturi scrubber occurred due to the difference between static pressure in the venturi scrubber and the hydrostatic pressure of water inside the tank. Dust particle removal efficiency has been calculated for inlet air velocities of 1 m/s and 3 m/s. It has been observed that removal efficiency is higher in case of higher inlet air velocity.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.2
• /
• pp.406-413
• /
• 2022

The subsea pipeline pre-commissioning stage consists of the following processes: Flooding, Venting, Hydrotesting, Dewatering, Drying, and N2 Purging. Among these processes, drying and nitrogen purging processes are stipulated to reduce and maintain the relative humidity below dew point to prevent the generation of hydrate and the risk of gas explosion in the pipeline during operation. The purpose of this study is to develop an analysis method for the air drying and nitrogen purging process during pre-commissioning of the subsea pipeline, and to evaluate the applicability of the analysis method through comparison with on-site measurement results. An analysis method using Computational Fluid Dynamics (CFD) was introduced and applied as a method for evaluating the relative humidity inside a subsea pipeline, and it was confirmed that analysis results were in good agreement with the on-site measurement results for the air drying and nitrogen purging process of the offshore pipeline. If the developed air drying and nitrogen purging analysis method are used as pre-engineering tools for pre-commissioning of subsea pipelines in the future, it is expected to have a significant impact on the improvement of work productivity.

• Journal of Environmental Impact Assessment
• /
• v.31 no.5
• /
• pp.286-295
• /
• 2022

In this study, the concentration distribution of indoor radon in Daejeon Metropolitan City was investigated and the reduction efficiency was evaluated by applying the radon reduction methods. Based on the results of the National Institute of Environmental Research, indoor radon measurements were conducted on 24 selected houses, and the average value of District A was 261 Bq/m3, far exceeding the standard, and even in the same house, indoor radon concentration was affected by measurement point and time. In the case of eight houses that applied the soil venting method to reduce radon, the indoorradon level was significantly lowerthan the standard value, and the average reduction efficiency was also around 55%, indicating a good reduction effect. In addition, the average reduction efficiency was around 90% in the two houses that carried out the shielding method, showing the very excellent effect of the indoorradon reduction. Even if the same reduction method is applied when reducing radon, the reduction efficiency may vary depending on various factors such as the structure of the building, the frequency of ventilation, and the season, so it is necessary to accurately evaluate the effectiveness of the reduction method in the future. Based on this, it is necessary to establish indoor radon management measures in Daejeon Metropolitan City to reduce human harm caused by radon exposure.

• Composites Research
• /
• v.37 no.3
• /
• pp.219-225
• /
• 2024

It is essential to develop a light-weight, high-performance structure for the deployable reflector antenna, which is the payload of a reconnaissance satellite, considering launch and orbital operation performance. Among them, the composite main reflector is a key component that constitutes a deployable reflector antenna. In particular, the development of a high-performance main reflector is required to acquire high-quality satellite images after agile attitude control maneuvers during satellite missions. To develop main reflector, the initial design of the main reflector was confirmed considering the structural performance according to the laminate stacking design and material properties of the composite main reflector that constitutes the deployable reflector antenna. Based on the initial design, four types of composite main reflectors were manufactured with the variable for manufacturing process. As variables for manufacturing process, the curing process of the composite structure, the application of adhesive film between the carbon fiber composite sheet and the honeycomb core, and the venting path inside the sandwich composite were selected. After manufacture main reflector, weight measurement, non-destructive testing(NDT), surface error measurement, and modal test were performed on the four types of main reflectors produced. By selecting a manufacturing process that does not apply adhesive film and includes venting path, for a composite main reflector with light weight and structural performance, we developed and verified a main reflector that can be applied to the SAR(Synthetic Aperture Rader) satellite.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.9
• /
• pp.4005-4012
• /
• 2014

Background: This study investigated the utilization of both problem and emotion focused coping strategies and their association with aspects of quality of life among Turkish women with ovarian cancer undergoing chemotherapy. Materials and Methods: The convenience sample consisted of 228 patients in all disease stages. The data were collected using the brief COPE, QOL-Cancer patient tool, sociodemographic sheet, and medical variables were gathered from patients' medical charts. Results: Findings reveal that quality of life is moderately high for this group of cancer patients, despite some specific negative facets of the illness and treatment experience. Acceptance, emotional support and religion were the most frequently used problem-focused coping strategies and self-distraction, venting and behavioral disengagement were the most frequently used emotion-focused coping strategies reported by patients. Overall quality of life and, particularly, psychological and spiritual well-being scores of younger patients were lower. Patients reported using significantly more problem-focused coping than emotion-focused coping, and more problem-focused and less emotion-focused coping predicted greater quality of life. Problem-focused coping was related to patients' physical and spiritual well-being and emotion-focused coping was related inversely with psychological and social well-being. Conclusions: Coping strategies are influential in patient quality of life and their psychosocial adaptation to ovarian cancer. Psycho-oncology support programs are needed to help patients to frequent use of problem-focused coping and reduce emotion-focused coping strategies to improve overall quality of life.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.501-503
• /
• 2007

오호츠크해 사할린 북동 해저사면지역은 세계적인 가스수화물 산출지역으로 알려져있다. 이미 2005년 탐사에서 50 cm 두께의 순수 가스수화물 시료를 해저면에서 채취한 지역이다. 2006년 탐사에서는 다양한 주파수대역의 고해상도 지구불리장비를 사용하여 탐사를 실시하였다. Side-scan Sonal와 3.5 kHz SBP 탐사, 수중음향 탐사를 통해 대규모 하도구조가 가스수화물지역의 북쪽 경계를 형성하고 있음을 밝혔다. 가스수화물의 BSR은 수심에 얕아짐에 따라 계속해서 심도가 감소하여 수심 약 300 m에서 해저면에 다다름. 이는 연구지역에서의 가스수화물 안정대의 상부경계가 약 300 m임을 시사한다 가스수화물 분출구조들은 약 1000m 수심을 경계로 천부에 분포하고, 해저면에는 원형의 가스분출구조들이 특징적으로 나타난다. 반면에 1000 m 수심보다 깊은 지역에서는 mud-dirpir의 상승구조로 판단되는 상승구조들이 해저면에 굴곡지형을 형성하고 있다. 해수중으로 분출하는 가스기둥들은 수심 111.2 m에서 1226.4 m 지점까지 다양한 수심에서 분포하며, 상승높이는 최대 750 m에 이르며, 약 150 m 수심까지 도달한다. 이는 해저에서 분출되는 메탄가스가 해수에 흡수되지 않고 해수면까지 이동하여 대기중으로 발출될 수 있음을 시사한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.77-80
• /
• 2006

Insensitive Munitions(IM) of solid propulsion system are defined as munitions that fulfil the performance and operational requirements, but will minimize the violence of a reaction when subjected to inadvertant stimuli. It should be clear that the reaction violence of rocket motor subjected to thermal stimuli can be mitigated by reducing confinement prior to propellant reaction. Devices designed to do this by venting the rocket motor case are commonly referred to as mitigation devices. The objective of this paper is to introduce the technical information related to the pyrotechnic mitigation devices for insensitive munition of solid rocket motor.