• Journal of the Korean Wood Science and Technology
• /
• 제25권3호
• /
• pp.16-23
• /
• 1997

This study was carried out to discuss feasibility of high density polyethylene(HDPE) as a new substitute for the conventional adhesives in plywood manufacture. Plywood was composed of radiata pine(Pinus radiata) and Malas(Homallium feotidium) veneers and bonded by HDPE. Adhesion characteristics and anatomical scanning has been examined through tensile-shear strength test and scanning electron microscopy(SEM). The results are as follows; 1. Optimum loading quantity was 15g/$(30.3{\times}30.3)cm^2$, and tensile-shear strength increased with the increase of loading quantity. 2. Even at the hot pressing time of 1 minute, tensile-shear strength met the value of KS(over the 7.5kgf/$cm^2$), and tensile-shear strength increased with the increase of hot pressing time. 3. Plywood composed of veneer at moisture content of 19.6% showed similar tensile-shear strength to that at air conditioned moisture content of 11.4%. 4. Under the same condition of hot pressing time, tensile-shear strength of plywood bonded by HDPE met the KS value of boil and wet test and proved the same group as phenol formaldehyde adhesive. 5. HDPE films showed mechanical adhesion through penetration into the lathe check and ray of veneer.

• Journal of the Korean Wood Science and Technology
• /
• 제47권2호
• /
• pp.239-248
• /
• 2019

This research presents an improvement of the physical and mechanical properties of composite board (com-ply) made of Oriented Strand Board (OSB) coated with wood veneer of Pine (Pinus merkusii), Avocado (Persea Americana) and Mahogany (Swietenia mahogany). 1.5 mm thick veneers of those three wood types were adhered to the surface of OSB using two adhesive types: epoxy and isocyanate. The adhesive with the glue spread of $250g\;m^{-2}$ applied using single glue line was spread and then cold pressed with the pressure of $15kg\;cm^{-2}$ for 3 hours. The research result showed an improving dimension stability of com-ply, but not found on all parameters of physical property test. The moisture content seemed to be influenced by the com-ply type, yet not related to its thickness swelling, water absorption and linear expansion. The exception took place in the parallel linear expansion when immersed for 2 hours. The highest to the lowest increases of MOE and MOR were consecutively found on OSB coated with wood veneer of Pine, Mahogany and Avocado. However, the increases were statistically insignificant. The highest increasing screw hold power was found at the com-ply type AE (avocado veneer and epoxy adhesive) that was by 28%.

• Journal of the Korean Wood Science and Technology
• /
• 제8권2호
• /
• pp.9-16
• /
• 1980

Papua New Guinea(PNG)산(産) TAUN재(材)를 이용한 합판제조 조건을 확립하였다. Taunwo(材)는 목질(木質)이 다양(多樣)하고 건조후 함수 분포가 균일(均一)치 못하여 퇴적(堆積)양생시키므로써 적정 함수분포를 유지할 수가 있었다. 또한 조직이 치밀하여 접착제와의 친화성이 낮아 집착불량이 용이하게 발생되기 쉬운 재(材)이나 제호시 수지율을 높여 도포하므로서 접착불량을 제거할 수가 있었다. Taun재(材)는 lauan재(材)나 kapur(材)와 혼합접합(混合接合) 하여도 접착력은 양호한 결과를 보였다.

• Journal of the Korean Wood Science and Technology
• /
• 제4권1호
• /
• pp.38-47
• /
• 1976

This study was carried out to exploit and utilize American sycamore (Platanus occidentalis) and poplar grown in Korea as veneer species for plywood manufacture. At this study to save the imported lauan logs and dollars, the effects affecting to the properties of plywood constructed by sycamore, poplar and lauan veneers were studied. Important items dealt with this study were dry and wet shear strength, moisture content, and specific gravities By the results and discussion it may be summarized as followings. 1) Sycamore core lauan plywood (A-II type) was shown best dry shear strength, and the next were all lauan veneer plywood (A-I type), poplar core lauan plywood (B-I type), lauan core sycamore plywood (A-III type) in order. There are no differences between dry shear strength of A-II type and A-I type, A-II type and B-I type plywood. 2) Wet shear strength showed the same order with dry shear strength. A-II type plywood showed best wet shear strength and it showed more difference than other plwoods. A-I type, B-I type and A-III type plywood were all very good without significant difference in wet shear strength. 3) B-I type plywood showed highest moisture content of all type plywood and the next were all sycamore(A-IV type) all poplar plywood (B-III type), A-III type, B-II type, A-II type pllywood in order. Generally high moisture content showed when two or three veneers were same species in the three layer plywood. 4) A-III type plywood showed highest specific gravity of all and the next was A-IV type plywood without a difference to A-I type plywood on the whole. plywoods constructed by lauan and sycamore were shown high specific gravities and the next was lauan, sycamore and poplar, lauan and poplar. It seemed to be that connected wi th the specific gravity of veneer itself in different species. 5) The plywood manufactured by extension of potato flour is not only superior but also profitable in the price aspect than the plywood manufactured by extension of wheat flour.

• Journal of the Korean Wood Science and Technology
• /
• 제16권1호
• /
• pp.3-8
• /
• 1988

This study was carried out to examine the effect of pretreatment of veneer with aluminum sulfate solution for the manufacture of the kapur plywood on the reduction of urea resin spread. The results were as follows: 1. Specific gravities of plywoods made of the kapur veneers ranged from 0.83 to 0.84 and their moisture contents based on air dry weight showed from 10.6% to 11.4%. These met the Korean Industrial Standards. 2. In the case of dry shear strength for the 3rd class plywood, 40% reduction- spread met K S as well as normal urea resin spread. pH of the aluminum sulfate solution gave better result at pH 4.5 and pH 6 than at pH 3. For the manufacture of the 2nd class plywood, hot and cold water-wet shear strength show the best results at the following conditions; such as 20% reduction spread, pH 4.5 of aluminum sulfate solution and all veneer treatment.

• Journal of the Korean Wood Science and Technology
• /
• 제24권1호
• /
• pp.34-47
• /
• 1996

Veneers of two nominal thicknesses, 1.5 and 2.5mm, were rotary peeled from Japanese larch (Larix leptolepis). Dahurian larch (Larix gmelinei) and Radiata pine (Pinus radiata) bolts unheated and heated in the water vat temperature of $66^{\circ}C$ by rising a final temperature at 10cm core of $60^{\circ}C$ to remain core diameter of 11.4cm. 1.5 and 2.5mm thick veneer cut from the heated Japanese larch were significantly thinner than those of the unheated bolt and 2.5mm thick veneer cut from the heated Dahurian larch were significantly thicker than that of the unheated bolt. 1.5mm thick Dahurian larch veneer and 1.5 and 2.5mm thick Radiata pine veneers showed insignificant difference between the unheated and heated bolts, respectively. Check distance on the loose side of 1.5mm thick veneer cut from the heated Radiata pine was significantly wider than that of the unheated bolt. However check distances on the loose side of 1.5 and 2.5mm thick Japanese larch and Dahurian larch veneers and 2.5mm thick Radiata pine veneers showed insignificant difference between the unheated and heated bolts. Also the depth of check on the loose side of three species showed insignificantly difference between the unheated and heated bolts. Arithmatic mean deviation($R_a$) and maximum height($R_{max}$) of the profile on the loose side of dried veneer by preheating the bolt compared with unheated bolts were different among apecies and between veneer thickness. The preheating treatment slightly affected qualities of these thin veneers such as 1.5 and 2.5mm. The yield of 2.5mm thick veneer from the heated radiata pine was significantly higher than that of the unheated bolt. However the yield of 2.5mm thick veneer for other two species and 1.5mm thick veneer for three species showed insignificant difference between the unheated and heated bolts. The yield of 2.5mm thick veneer for three species were higher than those of 1.5mm thick veneer. The average yields of green veneer of Japanese larch. Dahurian larch and Radiata pine were 57.1, 55.1 and 54.0 percent, respectively. Variables such as initial MC. drying time and veneer thickness had strong effect for Japanese larch veneer, less effect for Radiata pine veneer and nuch less effect on final MC for Dahurian larch veneer in jet drying. Correlation between the current MC and the drying time of Dahurian larch with low variation of initial MC was higher than those of Japanese larch and Radiata pine veneer with high variation of initial MC in high temperature drying. Thickness shrinkages of 2.5mm thick veneer for Japanese larch and Radiata pine were higher than those of 1.5mm thick veneers, but shrinkages of Dahurian larch veneer were similar between two nominal veneer thicknesses.

• Journal of the Korean Wood Science and Technology
• /
• 제38권5호
• /
• pp.414-420
• /
• 2010

The effect of polymeric diphenyl methane-4,4-diisocyanate (pMDI) or 1,6-hexamethylene diisocyanate (HDI) in the UMF resin was discussed for improvement of the dry and wet shear strengths of plywood manufactured from high moisture content veneers. The curing behavior of UMF resin by pMDI or HDI content was examined by DSC and TGA, and its adhesion performance was evaluated by dry and wet shear strength tests of plywood. With the increase of pMDI content in the UMF resin, the curing temperature, reaction enthalpy (${\Delta}H$), and thermal stability consistently increased. With the increase of HDI content in the UMF resin, however, the curing temperature and reaction enthalpy (${\Delta}H$) decreased consistently and the thermal stability slightly increased in the range of 200 to $400^{\circ}C$ but decreased beyond $400^{\circ}C$. Also, the dry tensile shear strength increased up to the pMDI content of 5% and then decreased with its further addition but the wet tensile shear strength showed slight tendency to increase with the increase of pMDI content in the UMF resin. As the HDI content increased, however, the dry and wet tensile shear strengths of plywood consistently increased.

• 한국가구학회지
• /
• 제21권4호
• /
• pp.284-292
• /
• 2010

This research was carried out to examine the properties of fancy cherry veneer overlaid on the PF resin bonded Meranti plywood floor, which 2.5% green tea leaf powder was applied in the UV varnishes and the adhesives for scavenging the volatile organic compounds. The results were as follows: 1. The various properties of the treated samples, such as density, moisture content, thickness swelling, bending strength(MOR), adhesion shear strength, surface abrasion, curling, cyclic delamination test with boiling water, boiling property, cold-resistance and heat resistance, acid resistance and alkali resistance, and anti-contamination property showed no significant difference between the properties of the control samples. 2.5% green tea leaf powder treated floor gave a little better results than the control for surface scratch test. 2. In case of QUV and weathering test, no difference between the treated sample and control was found. 3. The floor was discolored by adding 10% green tea leaf powder to UV coating, and the floor was also discolored to light green during by the soaking test. The color of floor was not changed up to 5% addition level.

• Journal of the Korean Wood Science and Technology
• /
• 제39권5호
• /
• pp.429-436
• /
• 2011

The selected physical and mechanical properties of non-certificated LVL circulated in domestic lumber market were investigated and compared to relevant standards. The tested LVL passed the moisture content and the soaking delamination rate limit as per domestic (KS) and Japanese standard (JAS). The evaluated mechanical properties were flatwise/edgewise bending strength, modulus of elasticity (MOE), horizontal shear and compressive strength. The 30 mm-thick LVL showed significantly higher bending strength than that of the 25 mm-thick LVL. The modulus of elasticity (MOE) showed same tendency in the results of bending strength. The edgewise bending strength and MOE were higher than that of flatwise bending strength and MOE. The horizontal shear strength values were also showed similar results to bending strength values. The tested results were compared each other and each products were graded according to JAS 701 grade specification. The failure mode of LVL in bending test showed the similar failure mode of solidwood that failed in a simple tension manner (splintery tension). The glue line failure was severe in 25 mm-thick specimens due to concentration of shear stress in layer discontinuity containing small voids and starved glue lines. In horizontal shear strength test, failure mode of LVL showed the typical horizontal shear failure. Compressive specimens failed with fiber crushing in company with apparent delamination that splitted along the length of the specimens. From the results, the complete bonding between lamination and consistency in thin veneer layer were considered as a critical factor in the mechanical properties of LVL. Moreover, the standard test procedure and specification for non-certificated LVL should be required to check the performance of uncertificated materials.

• Journal of the Korean Wood Science and Technology
• /
• 제39권3호
• /
• pp.221-229
• /
• 2011

목질계 판상재료 생산을 위하여 현재 주로 사용되고 있는 석유화학계 접착제는 원유의 가격 상승과 포름알데히드 방산과 같은 문제로 인해 대체 접착제에 대한 개발 필요성이 오래전부터 대두되었다. 본 연구에서는 석유화학계 접착제를 대체하기 위하여 바이오 디젤 부산물인 유채박의 효소 가수분해를 통해 접착제를 조제하고, 이 접착제를 단판적층재 제조에 적용한 후 물리 및 기계적 특성을 조사하여 유채박의 단판적층재 제조용 접착제 제조를 위한 원료화 가능성을 확인하고자 수행하였다. 먼저 유채박 접착제 조제를 위하여 유채박을 4가지 효소의 조합을 통해 개량한 다음, phenol formaldehyde (PF) prepolymer와 혼합하여 접착제를 제조하고 이를 단판적층재 제조에 사용하였다. 제조된 단판적층재의 평균함수율과 내수성은 모두 KS의 기준을 만족시키는 것으로 나타났으며, 유채박 접착제의 열분석에서 pectinase 가수분해물로 조제한 접착제를 제외하고 페놀수지 접착제와 열경화 특성이 큰 차이를 보이지 않았다. 단판적층재의 휨강도는 페놀수지 접착제로 제조한 단판적층재보다 높거나 유사한 것으로 나타나 기존 석유화학계 접착제의 대체 접착제로써 가능성을 보여주었다. 추후 접착성능의 향상을 위해 적절한 유채박의 효소가수분해 조건에 대한 연구와 도포성능 개선에 대한 연구가 필요할 것으로 생각된다.