• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.4
• /
• pp.363-369
• /
• 2009

A vibration analysis for a rotating cantilever beam with the tapered cross section is presented in this study. The stiffness changes due to the stretching caused by centrifugal inertia forces when a tapered cantilever beam rotates about the axis perpendicular to its longitudinal axis. When the cross section of cantilever beam are assumed to decrease constantly, the mass and stiffness also change according to the variation of the thickness and width ratio of a tapered cantilever beam. Such phenomena result in variations of natural frequencies and mode shapes. Therefore it is important to the equations of motion in order to be obtained accurate predictions of these variations. The equations of motion of a rotating tapered cantilever beam are derived by using hybrid deformation variable modeling method and numerical results are obtained along with the angular velocity and the thickness and width ratio.

• 한국해양학회지
• /
• v.16 no.1
• /
• pp.1-11
• /
• 1981

The seasonal variations of surface current patterns in the Japan Sea were drawn out from the results of drift bottle experiments, current measurements and hydrographic observations during 1979∼1980. The North Korean Cold Current(NKCC) and the East Korean Warm Current(EKWC) were common features of circulation in the eastern sea of Korea. The intrusion of NKCC along the Korean coast became strong in summer(average velocity of 47.4cm/sec off Jumunjin and 23.4cm/sec near Jugbyeon) when the Tsushima Current was strong. But there was no indication of the NKCC in November 1979. Dynamic topography(August & November 1979) and satellite picture(November 1979) seemed to show the topographic steering of EKWC beginning off Janggigab. Drift bottles arrived at the Japaness coast were affected significantly by the strong Tsushima Current in summer and by the predominant northwesterlies in winter instead of weak current.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.6 no.3
• /
• pp.193-205
• /
• 1994

A simulation program of the plate finned-tubes condenser widely used in the air conditioning system was developed. The program took into account the variations of the flow properties and fluid friction factor of refrigerant, and the heat transfer coefficients of refrigerant and air sides. The program was applied to a copper tube condenser which has outside diameter of 10.05mm, inside diameter of 9.35mm, length of 5.20m and three rows arraied staggered. Simulation results were such that refrigerant was super-heated state from the entrance to the 0.14m point, two-phase flow from the 0.14m point to the 4.10m point, sub-cooled state from the 4.10m point to the outlet. The degree of sub-cooled was $6.1^{\circ}C$. The variations of refrigerant quality, temperature, pressure, velocity, specific enthalpy, specific volume and air temperature, tube temperature were showed.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.5
• /
• pp.134-142
• /
• 1994

An upper bound elemental technique (UBET) is applied to predict variations of neutral plane and optimal position of the initial billet for rib-wep shaped ring forging. In the analysis, the neutral plane position and velocity fields are determined by minimizing the total power consump- tion with respect to chosen parameters. The degree of die-cavity filling by initial billet-position and the variations of neutral plane by friction condition are investigated. Experiments have been carried out with pure plasticine billets at room temperature. The theoretical predictions of the forging load and the flow pattern are in good agrement with the experimental results.

• Tribology and Lubricants
• /
• v.23 no.2
• /
• pp.49-55
• /
• 2007

A numerical analysis of elastohydrodynamic lubrication of elliptical contacts with both rolling and spinning has been carried out. A finite difference method with non-uniform grid systems and the Newton-Raphson method are applied to solve the problems. The velocity vectors resulting from combined spinning and rolling/sliding motion lead to asymmetric pressure distributions and film shapes. Pressure distributions, film contours and variations of the minimum and central film thicknesses are compared with various spin-roll ratios. Reduction of the minimum film thickness under spinning is remarkable whereas the central film thickness is relatively less. The spin motion have large effect on variations of the minimum film thickness with load parameter which are small in pure rolling/sliding cases. Therefore present numerical scheme can be used in the analysis of general elliptical contact EHL problems and further studies are required.

• Tribology and Lubricants
• /
• v.24 no.6
• /
• pp.355-361
• /
• 2008

In highly stressed machine elements such as angular contact ball bearings and toroidal type traction drives, the elastohydrodynamic lubrication of elliptical contacts with both rolling and spinning motion are occur. In this paper, a finite difference method with non-uniform grid systems and the Newton-Raphson method are applied to solve the problems. Pressure distributions, film contours and variations of the minimum and central film thicknesses are compared with various ellipticity parameter, dimensionless speed and load parameter. The results showed that the spinning motion has significant influence especially on the film shapes. Reduction of the minimum film thickness under spinning is remarkable whereas the central film thickness is relatively less. Especially variations of the minimum film thicknesses with rolling velocity, load and ellipticity ratio are a great different from those of pure rolling. Therefore present numerical scheme can be used in the analysis of general elliptical contact EHL problems and further studies are required.

• 한국전산유체공학회:학술대회논문집
• /
• 2002.10a
• /
• pp.53-63
• /
• 2002

In this numerical approach, strut-placed supersonic annular flow is examined. The geometrical variations of strut cause strong influence on flowfield structures. The geometrical variations are as follows, swept effect, attack angle effect, variation of leading edge shape. These changed features such as velocity structure, pressure structure, shock-boundary layer interaction are compared and analyzed according to each geometrical configuration.

• Smart Structures and Systems
• /
• v.21 no.2
• /
• pp.163-170
• /
• 2018

The dynamic response of a finite length thermo-piezoelectric rod with variable material properties is investigated in the context of the fractional order theory of thermoelasticity. The rod is subjected to a moving heat source and fixed at both ends. The governing equations are formulated and then solved by means of Laplace transform together with its numerical inversion. The results of the non-dimensional temperature, displacement and stress in the rod are obtained and illustrated graphically. Meanwhile, the effects of the fractional order parameter, the velocity of heat source and the variable material properties on the variations of the considered variables are presented, and the results show that they significantly influence the variations of the considered variables.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 1999.11a
• /
• pp.126-129
• /
• 1999

Natural ventilation is achieved by air exchanges through multiple openings due to natural pressure variations inside and outside the greenhouse. Wind is the primary driving force making natural ventilation systems very difficult to design properly because of variations in wind velocity and direction. The optimization of these systems for acceptable climate control requires a thorough knowledge of the airflow rates and patterns as related to weather conditions and greenhouse structural details. (omitted)

• 한국가시화정보학회:학술대회논문집
• /
• 2002.11a
• /
• pp.35-38
• /
• 2002

Variations of temperature and velocity fields in a Hele-Shaw Convection Cell (HSC) were measured using a holographic interferometry and PIV technique with varying Rayleigh number. Experimental results show a steady flow pattern at low Rayleigh numbers and a time-dependent periodic flow at high Rayleigh numbers. Two different measurement methods of holographic interferometry, double-exposure method and real-time method, were employed to measure the temperature field variations of HSC convective flow. In the double-exposure method, unwanted waves can be eliminated and reconstruction images are clear, but transient flow structure cannot be observed clearly. On the other hand, transient flow can be observed and reconstructed well using the real-time method. PIV results show that flow inside the HSC is periodic and the oscillating state is well matched with the temperature field results. The holographic interferometry and PIV techniques employed in this study are useful for analyzing the unsteady convective thermal fluid flows.