• Spatial Information Research
• /
• v.23 no.3
• /
• pp.79-89
• /
• 2015

Once the building is higher than certain size, the wind effect plays very important role in structure design. Moreover, this is more important in Korea because dangerous phenomena like typhoons are common. Rational wind resistant design is being magnified considering the global flow and climate changes. This research presented the estimation method of design wind load using spatial information analysis based on 1:5,000 digital map and performed comparative analysis with actual application cases. The wind velocity pressure exposure coefficient and topographic coefficient turned out to be more quantitative and rational when calculated through the proposed method. The time and cost are comparatively low when compared with traditional method which contribute to the economic and rational wind resistant design.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.10
• /
• pp.1327-1333
• /
• 2018

Numerical analysis has the advantage that no actual flow pathways need to be formulated, making this technique especially useful for simulation analysis such as pathway design. However, it does require that the complete physical parameters of the fluid and the complete boundary conditions be known. If any of them are unknown, either the calculation will become impossible, or even if the calculation does converge, the reliability of the result will be low. Therefore, a means of more accurate acquisition of flow information is required. In this paper, we present techniques for estimating flow field from a constraint equation for image information and velocity field, based on the image intensity changes accompanying the motion of dye in waterway. In the equation, we entered a stabilizing term to suppress estimation error. We show the effectiveness of our method through experiments with generated and real images of a Karman vortex.

• Journal of the Korean earth science society
• /
• v.28 no.7
• /
• pp.903-913
• /
• 2007

In this study, the researchers compared the S-wave velocity structures obtained by two kinds of dispersion curves: phase and group dispersions from a tidal flat located in the SW coast of the Korean peninsula. The ${\tau}-p$ stacking method was used for the phase velocity and two different methods (multiple filtering technique: MFT and continuous wavelet transform: CWT) for the phase velocity. It was difficult to separate higher modes from the fundamental mode phase velocities using the ${\tau}-p$ method, whereas the separation of different modes of group velocity were easily achieved by both MFT and CWT. Of the two methods, CWT was found to be more efficient than MFT. The spatial resolutions for the inversion results of the fundamental mode for both phase and group velocities were good for only a very shallow depth of ${\sim}1.5m$. On the other hand, the spatial resolutions were good up to ${\sim}4m$ when both the fundamental and the 1st higher mode poop velocities obtained by CWT were used for S-wave inversion. This implies that the 1st higher mode Rayleigh waves contain more information on the S-wave velocity in deeper subsurface. The researchers applied the CWT method to obtain the fundamental and the 1st higher mode poop velocities of the S-wave velocity structure of a tidal flat located in SW coast of the Korean peninsula. Thea the S-wave velocity structures were compared with the borehole description of the study area.

• Geophysics and Geophysical Exploration
• /
• v.12 no.2
• /
• pp.173-182
• /
• 2009

In April 2008, KIGAM carried out an ocean-bottom seismometer (OBS) survey in the central Ulleung Basin where strong bottom simulating reflectors (BSRs) were revealed from previous surveys and some gas-hydrate samples were retrieved by direct sampling. The purpose of this survey is to estimate the velocity structure near the BSR in the gas hydrate prospect area using wide-angle seismic data recorded on the ocean-bottom seismometers. Along with the OBS survey, a 2-D seismic survey was performed whereby stratigraphic and preliminary velocity information was obtained. Two methods were applied to wide-angle data for estimating P wave velocity; one is velocity analysis in the $\tau$-p domain and the other is seismic traveltime inversion. A 1-D interval velocity profile was obtained by the first method, which was refined to layered velocity structure by the latter method. A layer stripping method was adopted for modeling and inversion. All velocity profiles at each OBS site clearly show velocity reversal at BSR depths due to the presence of gas hydrates. In addition, we could confirm high velocity in the column/chimney structure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.2
• /
• pp.107-113
• /
• 2019

In this paper, a robust filter based wind velocity estimation algorithm without an air velocity sensor in an air vehicle is presented. The wind velocity is useful information for the air vehicle to perform precise guidance and control. In general, the wind velocity can be obtained by subtracting an air velocity which is obtained by an air velocity sensor such as a pitot-tube, and a ground velocity which is obtained by a navigation equipment. However, in order to simplify the configuration of the air vehicle, the wind estimation algorithm is necessary because the wind velocity can not be directly obtained if the air velocity measurement sensor is not used. At this time, the aerodynamic coefficient of the air vehicle changes due to the turbulence, which causes the uncertainty of the system model of the filter, and the wind estimation performance deteriorates. Therefore, in this study, we propose a wind estimation method using $H{\infty}$ filter to ensure robustness against aerodynamic coefficient uncertainty, and we confirmed through simulation that the proposed method improves the performance in the uncertainty of aerodynamic coefficient.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1986.04a
• /
• pp.27-28
• /
• 1986

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1996.10a
• /
• pp.915-918
• /
• 1996

• Spatial Information Research
• /
• v.21 no.5
• /
• pp.43-51
• /
• 2013

In this study, the concept of spatial big data and effective ways to build a spatial big data system are presented. Big Data is defined as 3V(volume, variety, velocity). Spatial big data is the basis for evolution from 3V's big data to 6V's big data(volume, variety, velocity, value, veracity, visualization). In order to build an effective spatial big data, spatial big data system building should be promoted. In addition, spatial big data system should be performed a national spatial information base, convergence platform, service providers, and providers as a factor of production. The spatial big data system is made up of infrastructure(hardware), technology (software), spatial big data(data), human resources, law etc. The goals for the spatial big data system build are spatial-based policy support, spatial big data platform based industries enable, spatial big data fusion-based composition, spatial active in social issues. Strategies for achieving the objectives are build the government-wide cooperation, new industry creation and activation, and spatial big data platform built, technologies competitiveness of spatial big data.

• Proceedings of the IEEK Conference
• /
• 2000.06d
• /
• pp.50-53
• /
• 2000

In this work, the new algorithm that automatically extracts moving object of the video image is presented. In order to extract moving object, it is that velocity vectors correspond to each frame of the video image. Using the estimated velocity vector, the position of the object are determined. the value of the coordination of the object is initialized to the seed, and in the image plane, the moving object is automatically segmented by the region growing method. As the result of an application in sequential images, it is available to extract a moving object.

• Journal of Biomedical Engineering Research
• /
• v.7 no.1
• /
• pp.75-79
• /
• 1986

In this paper, a multigate pulsed doppler system with parallel signal processing which enables the transcutaneous assesment of the blood-flow velocities of five adjacent sample volumes is developed. The outputs of the system are audio signals, velocity curves and velocity profiles of 5 adjacent sample volumes. We have applied to the major superficial arteries and obtained the detailed information about the time dependent blood-flow behavior.