• 한국가스학회지
• /
• 제23권3호
• /
• pp.27-32
• /
• 2019

본 연구에서는 단일 원관에서 입구의 유속이 일정한 경우와 주기적인 변동이 있는 경우에 대하여 시간에 따라 원관 주위에서 와류 분포와 온도 분포 변화를 비교 분석하였다. 또한, 양력과 항력의 시간 변화와 PSD(power spectral density)를 분석하여 유동의 주파수 특성을 규명하였다. 일정 입구 유속의 경우는 잘 알려진 칼만 와류 분포를 보여 주었으며 원관의 상하에서 교대로 와류가 발생하는 것을 관찰할 수 있었다. 주기적인 입구 유속 변동의 경우는 원관의 상하에서 동시에 와류가 발생하는 것을 관찰할 수 있었다. 두 가지 모두 시간에 따른 온도 분포 변화는 와류 분포 변화와 거의 유사하게 거동하는 것을 확인할 수 있었다. 일정 입구 유속의 경우의 와류 유동 주파수는 31.15 Hz 이며 주기적인 입구 유속의 경우는 와류 유동 주파수는 입구 유속의 주파수와 동일하게 15.57 Hz으로 나타났다. 원관 표면 평균 누셀수는 일정 입구 유속의 경우는 99.6이며 주기적인 입구 유속 변동의 경우는 110.7로 나타나서 주기적인 입구 속도 변동의 경우가 열전달이 11.1% 증가하는 것을 알 수 있었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.975-985
• /
• 2011

Cu-Matrix sintered brake pads and low alloyed heat resistance steel are most applied to basic brake system for high energy moving machine. In this research, we analyzed tribological characteristics for influence of air velocity between disk and pad. At low brake pressure with air flow, friction stability was decreased due to no formation of tribofilm at disk surface. But there are no significant change of friction coefficient at all test conditions. Wear rate of friction materials were decreased with increasing of air flow velocity. In result, air flow velocity influenced friction stability, wear rate of friction materials and disk but not friction coefficient.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1635-1638
• /
• 1997

A measurement of conduction veloctiy of the action potentials along the muscle fibres has been applied to various diagnosis. When we measure muscle fiber conduction velocity, it occurs that not only change of conduction velocity but alos inclusion of mipulse component by physiological and experimental reason. So, robuster time delay estimation algorithm than general methods[1] is needed to find correct time delay form these signals. In this paper we, propose new time delay estimation algorithms, robust in impulsive noise, by using characteristic of .alpha.-stable distribution whcih defines impulsive noise well. Then we apply proposed algorthms to measure muscle fiber conduction velocity and compare them with other studies.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.75-81
• /
• 2001

This paper presents the atomization characteristics of single hole injector in the direct injection type diesel engine. The spray characteristics of fuel injector such as the droplet size and velocity were measured by phase Doppler particle analyzer. In this paper, the atomization characteristics of fuel spray are investigated for the experimental analysis of the measuring data by the results of mean diameter and mean velocity of droplet. The effect of fuel injection pressure on the droplet size shows that the higher injection pressure results in the decrease of mean droplet diameter in the fuel spray. The minimum size of fuel spray droplet appears on the location of 40mm axial distance from nozzle exit of diesel injector. Based on the experimental results, the correlation between the droplet diameter and mean velocity of the diesel spray due to the change of axial and radial distance from the nozzle tip were investigated.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.371-374
• /
• 2003

The bending process for the "ㄱ" section product can be developed by the hot metal extrusion machine with the two punches moving in the different velocity. The bending phenomenon can be controlled by difference of velocity at the die exit section by the different velocity of billets through the two-hole container. The results of the experiment show that "ㄱ" section product can be bended by the extrusion process and that the curvature of the product can be controlled by the velocity of punch and that the defects such as the distortion of section and the thickness change of the product and the folding and wrinkling of the product did not happen after the bending processing by the extrusion bending machine.

• 한국멀티미디어학회논문지
• /
• 제18권11호
• /
• pp.1400-1407
• /
• 2015

In the paper, we suggest bettered EHMECS(Enhanced Hybrid Multi Electrical Cupping System) to regulate automatically vacuum pressure using many cupping cup at once. We controlled accurately the pressure using S-PI control technique in pump motor to input the air inside cupping cup. S-PI control compared constant velocity, load and velocity variance between existing PI and FLC(Fuzzy Logic Control). The stabilization time of suggested S-PI control improve 20% of existing PI and 8% of FLC. The error constant of normal condition improved 71% of existing PI and 62% of FLC in steady speed and 80% of existing PI and 67% of FLC in load change. Also the error constant about velocity variance improve 45% of PI control. It is prove the suggested S-PI control technique. When use long time vacuum pressure of cupping cup regulated the suggested S-PI control technique, can loosen knotted muscles.

• Wind and Structures
• /
• 제25권4호
• /
• pp.381-395
• /
• 2017

Nonlinear vibration and instability of cylindrical shell conveying fluid-nanoparticles mixture flow are studied in this article. The surrounding elastic medium is modeled by Pasternak foundation. Mixture rule is used for obtaining the effective viscosity and density of the fluid-nanoparticles mixture flow. The material properties of the elastic medium and cylindrical shell are assumed temperature-dependent. Employing first order shear deformation theory (FSDT), the motion equations are derived using energy method and Hamilton's principal. Differential quadrature method (DQM) is used for obtaining the frequency and critical fluid velocity. The effects of different parameters such as volume percent of nanoparticles, boundary conditions, geometrical parameters of cylindrical shell, temperature change, elastic foundation and fluid velocity are shown on the frequency and critical fluid velocity of the structure. Results show that with increasing volume percent of nanoparticles in the fluid, the frequency and critical fluid velocity will be increases.

• 한국정밀공학회지
• /
• 제5권4호
• /
• pp.24-31
• /
• 1988

The Upper Bound Solution has been used to investigate the effect of the various parameters on the floating-plug tube-drawing precess. A kinematically admissible velocity field considering the change of the tube thickness is proposed for the deformation process. Taking into account the position of the plug in the deforming region, shear energy at entrance and exit, friction energy on contact area, homogeneous energy are calculated. The theoretical values in proposed velocity field are good agreement with experimental values, It is investigated that the tube thickness in the deforming region is changed slightly toward minimization of deforming energy and then the drawing stress in lower than the crawing stress in the velocity field that the tube thickness is uniform.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.103-106
• /
• 2000

Nondestructive tests are useful method in rapidly evaluating the condition of existing concrete structures. An objective of this work is to investigate the factors influencing the longitudinal wave velocity-strength relationship, such as w/c ratio, curing temperature, curing condition. Test results show that a change in the w/c ratio ranging from 0.46 to 0.88 and in the curing temperature from 1$0^{\circ}C$ to 3$0^{\circ}C$ did not alter the velocity-strength relationship. however, curing methods had significant effects on the velocity-strength relationship. Therefore, the estimation of compressive strength until 28 day can be accomplished by only a nonlinear equation with consideration of curing condition.

• 대한기계학회논문집A
• /
• 제27권8호
• /
• pp.1324-1330
• /
• 2003

A cylindrical cam with a translating roller follower provides to change the rotational motion of the cam to the translation motion of the follower. It's a very useful mechanism in the automation. But, it's very difficult that the shape is defined accurately. This paper proposes a shape design method of the cylindrical cam with a translation roller follower using the relative velocity method$\^$(9,11-13)/ : The relative velocity method calculates the relative velocity of the follower versus the cam at a center of roller, and then determines a contact point by using the geometric relationships and the kinematical constraints. Finally, we present examples in order to prove the accuracy of the proposed methods.