• International journal of advanced smart convergence
• /
• 제12권4호
• /
• pp.443-450
• /
• 2023

One of the basic tasks in the automobile manufacturing process is to design a bare chassis, which is the basic frame of a vehicle, and a bracket is a member connecting various devices to the frame. Bracket, which is a member connecting the engine, transmission, and suspension, which are the core devices of driving and operating the vehicle, to the frame, must maintain safety during vehicle operation. If the bracket connecting the various devices constituting the vehicle to the frame does not have durability, serious accidents may occur during operation of the vehicle. In this study, we performed stress analysis on the brackets installed in the bare chassis of the 25-passenger bus in the development stage. Based on the stress analysis performed, an improved bracket dimension was proposed.

• 전자공학회논문지
• /
• 제50권9호
• /
• pp.46-51
• /
• 2013

본 논문에는 무인항공기에 장착된 UHF 안테나의 최적 위치 및 형상이 다양한 위치에서 EM 시뮬레이션을 통하여 분석되어져 있다. EM 시뮬레이션을 위하여 FEKO를 이용하였다. 시뮬레이션의 복잡도를 줄이고 분석시간과 메모리 이용도를 최소화하기 위하여 비행체의 복합체 구조를 레이돔 구조를 제외하고 PEC 모델로 간략화 하였다. 시뮬레이션은 무인항공기의 날개와 Ventral Fin 위치에서 수행되어 졌고, 안테나 형상은 모노폴, 다이폴, 굴곡형 모노폴 안테나들을 이용하였다. 모노폴 안테나가 비행체 날개에 장착될 경우, 오른쪽 날개와 왼쪽 날개에 각각 장착되어지기 위하여 두 개의 안테나가 필요하고, 이 두 개의 안테나들은 가시선 데이터링크 지상 안테나에 대한 무인항공기 날개 방향에 따라 전환되어져야 한다. 모노폴 안테나가 Ventral Fin에 장착될 경우, 가시선 데이터링크 지상 안테나에 대한 무인항공기 날개 방향에 상관없이 하나의 안테나로 운용 가능하다. 또한, 안테나 이득도 비행체에 의한 Blockage 감소로 개선되어진다. 안테나 이득은 굴곡형 모노폴 안테나를 이용하여 더욱 더 개선되어 진다. 결론적으로 무인항공기에 장착된 UHF 안테나의 최적 위치 및 형상은 굴곡형 모노폴 안테나를 Ventral Fin 아래에 장착하는 것이다.

• 한국인쇄학회지
• /
• 제23권2호
• /
• pp.1-14
• /
• 2005

Generally, printing inks are composed of pigment, vehicle and additive. Among others, the vehicle transfers the pigment to substrate and then binds it on the surface. So, rheological properties of the vehicle are an important factor which has influence on printability. Thus, in this study, rheology of the vehicle was investigated by using rotational rheometer according to molecular weight of resin. Also, emlusion rheology of water in oil type and its microstructure were examined with increasing the shear rate. Consequently, the following results were obtained: (1) By viscometric flow test, zero shear viscosity and shear thinning index of vehicle increased with increasing the molecular weight of resin. (2) By relaxation and creep test, relaxation time and retardation time of vehicle increased with increasing the molecular weight of resin. (3) By frequency sweep test, crossover point of vehicle increased with increasing the molecular weight of resin. (4) G' and G" of emlusions increased with increasing the molecular weight by amplitude sweep test. (5) The shape of water drop in emlusions was changed to the capillary tube.

• 한국공작기계학회논문집
• /
• 제16권3호
• /
• pp.96-102
• /
• 2007

An Optimal shape design of the boom system in high ladder vehicles is performed using 3-D finite element method (FEM). Results of structural analyses providing displacements, stresses are implemented for the optimum shape design. Lanzcos algorithm is used for the modal analysis in order to find natural frequencies. The optimal shape including cross sectional thickness and length of the boom system is controlled by the subproblem method besed on displacement and Von Mises stress. It is found that a plenty of materials can be saved by using shape design optimization in high ladder vehicles. It is also found that the natural frequency is increased until 6th mode and maintained similarly or decreased after 6th mode.

• 대한인간공학회지
• /
• 제25권2호
• /
• pp.85-94
• /
• 2006

The purpose of this study is to extract typical body shapes of Korean adults based on the three-dimensional Korean anthropometric data measured through 5th national anthropometric survey and to examine the suitability of the 3-D human shape data for the interior packaging. 36 three-dimensional anthropometric variables related to the design of vehicle interior were considered for the appraisal of typical body shapes. Four major factors were extracted by the factor analysis and factor scores were calculated for all subjects. Typical or standard drivers of Korean adults were selected by the minimum deviation criteria for the four factor scores with respect to 5th, 50th, and 95th percentiles, respectively. Typical drivers of Korean adults were visualized by the CATIA-HUMAN program due to the absence of proper application software for three-dimensionally scanned human body data. There are considerable differences between the anthropometric data of Korean adults and those provided by CATIA-HUMAN program, which shows that the modeling data provided by CATIA-HUMAN should not be directly applied to the ergonomic evaluation for the vehicle design. This suggests the necessity for the development of suitable software for scanned human shape data. It is also expected that the anthropometric data of typical drivers extracted from this study help design package layouts and improve the suitability of ergonomic evaluation for Korean customers.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권12호
• /
• pp.718-724
• /
• 2004

This study investigates the design factors of Interior Permanent Magnet Synchronous Motor(IPMSM) which is applied to Hybrid electric vehicle as a driving power. Recently, there are many studies of IPMSM for application to Hybrid Electric Vehicle, because IPMSM has characteristics of high torque, high power density and high efficiency which come from reluctance torque due to difference of inductance as well as magnet torque. This study analyzes the inductance and design characteristics of IPMSM by using finite element method and focuses on design and analysis of IPMSM which can operates with high efficiency at low speed range. For this embodiment, magnet shape is changed from conventional block type to arc type without any change of outline dimension of motor and this change of magnet shape makes it possible to increase back EMF and sinusoidal waveform. Analysis results are verified by test of improved and embodied motor. As a test result , increased back EMF and sharply decrease of harmonics are secured and through this contribution of reduced fuel consumption of Hybrid electric vehicle is expected.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.565-568
• /
• 2002

In the flow analysis around a bluffbody such as road vehicles, drag reduction has been of the primary concern mainly due to the effect on fuel economy. To reduce the drag, which is mostly due to the pressure difference caused by the flow separation, the location of the separation and eddy sizes are controlled. However, less attention has been given to the effect of the lift. The effect of lift may cause the driving stability problem of the vehicle at high speed white heavy downward effect of lift together with the vehicle weight may require more power to drive the vehicle forward. It is considered worthwhile to pursue the optimal design of the low drag tail shape of the MIRA model while taking the lift effect into account, even though it is considered as a reference. To this end, a commercial multi-objective optimization code, FRONTIER, Is used together with the CFD code, STAR-CD. It is hoped that the results will provide more insight into the flow field around the bluffbody as transportation means.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.222-228
• /
• 2007

In order to solve the problem of traffic holdups and environmental pollution(contamination), several metropolises are operating the subway and many local government plans hereafter the light rail vehicle operation and it is in the process of preparing. This point of time, it need to evaluate the comfortable characteristic of the seat which is closely connected with passenger and it should be reflected to the product design through the data analysis. The methods of the comfortable characteristic evaluation should be considered to various methods from physical factor to psychological factor. Among these, the most universal and possible quantitative measurement estimate through 'Body pressure measurement system'. From this paper, it was measured the body pressure of the subway seat which is in the process of operating in a domestic and it will be compared and analyzed the material & seat shape, so we evaluated the comfortable characteristic of the short-distance transportation railway vehicle. It was operated the man and woman who belongs in standard shape of Korean, we compared and analyzed the Peak position where the body pressure is visible and body pressure spread out.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.115-120
• /
• 2008

The fatalities of pedestrian accounted for about 40.0% of all fatalities in Korea (2005 year). In pedestrian involved accident, the most important data to inspect accident is throw distance of pedestrian. The throw distance of pedestrian can be influenced by many variables, such as vehicular frontal shape, vehicular impact speed, the offset of impact point, the height of pedestrian, and road condition. The trajectory of pedestrian after collision can be influenced by vehicular frontal shape classified into sedan type, box type, SUV type and van type. Many studies have been done about pedestrian accident with passenger car model and bus model for simple factors. But the study of pedestrian accident by van type vehicle was much insufficient, and even that the influence of multiple factors such as the offset of impact point was neglected. In this paper, a series of pedestrian kinetic simulation were conducted to inspect relationship between throw distance and multiple factors with using PC-CRASH s/w, a kinetic analysis program for a traffic accident for van type. By based on the simulation results, multi-variate regression was conducted, and regression equation was presented.

• 한국자동차공학회논문집
• /
• 제23권3호
• /
• pp.254-262
• /
• 2015

This paper presents 3D collision deformation modelling methodologies using photogrammetry for reconstruction of vehicle accidents. A vehicle's deformation shape in collision provides important information on how the vehicle collided. So effective measurement(scanning) and construction of a corresponding appropriate model are essential in the analysis of collision deformation shape for obtaining much information related to collision accident. Two measurement methods were used in this study: Indirect-photogrammetry which requires relatively small amount of photos or videos, and direct-photogrammetry which requires large amount of photos directly taken for the purpose of 3D modelling. When the indirect-photogrammetry method, which was mainly used in this study, lacked enough photographic information, already secured 2D numerical deformation data was used as a compensation. This made 3D collision deformation modelling for accident reconstruction analysis possible.