• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1352-1355
• /
• 1997

This paper presents the algorithm for estimating the attitude of an underwater vehicle using EFK. The system model is designed by linerizing the nonlinear Euler angle differential equation and the measurements is a speed logger output. The simulation result shows that the estimation lagorithm is adequate for decreasing attitude errors that grow abruptly during the motion with acceleration and rotation. It also shows that we can adapt the algorithm for compensating initial attitude errors generated after initial leveling.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.204-208
• /
• 2003

This study presents a clutch-by-wire system for automotive which can be utilized on a vehicle with a manual transmission real time while the vehicle is in motion. The system consists of air valve, spring, oil pressure control valve, oil pressure cylinder, switch, etc. In this study, commercial vehicle was studied on improvement of no clutch pedal system. Therefore the results obtained effective driveability, gear shiftability, convenience for driver.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.772-775
• /
• 1992

It is necessary to estimate hydrodynamic coefficients to design the auto-pilot system and motion simulator of submersible vehicle. In this paper, an algorithm was designed to estimate hydrodynamic coefficients of submersible vehicle. Using this algorithm, the hydrodynamic coefficients were estimated from measurements of full scale trial. The estimated hydrodynamic coefficients were used for the design of an auto-depth controller(ADC) of submersible vehicle, and the resulting ADC are proved to have a better performance than the previous one.

• 한국컴퓨터정보학회논문지
• /
• 제27권6호
• /
• pp.117-122
• /
• 2022

본 논문에서는 IoT와 저 전력 장거리 통신(NB-IoT)기술을 적용한 차량관제용 단말기를 개발했다. 본 시스템은 주차중인 차량의 위치, 상태에 대한 정보를 수집하고, 저 전력 실시간으로 차량 소유자의 단말로 차량 상태를 전송하여 차량의 도난을 방지하고, 주행 중인 차량의 경우, 주행 속도, 급제동, 미끄러짐, 충격 등 차량의 1차 정보를 수집하여 서버로 전송하면 서버에서 관련 데이터를 분석하여 교통 정체, 도로 파손 안전사고 발생 등에 대한 2차 정보를 생성할 수 있으며, 주기적 알람 형태로 목적지의 예상 도착 시간을 전송하여 목적지에 차량의 정확한 도착 시간을 알 수 있다. 본 단말 장치는 차량용 IoT 게이트웨이로 차량 내부의 다양한 유무선 센서와 연결될 수 있다. 또한 자동차의 유지관리, 효율적인 운행과 차량들에게서 수집된 데이터를 민간 또는 공공부분에서 유용하게 활용할 수 있다.

• Ocean Systems Engineering
• /
• 제1권4호
• /
• pp.297-315
• /
• 2011

New applications of streamlined Autonomous Underwater Vehicles require an AUV capable of completing missions with both high-speed straight-line runs and slow maneuvers or station keeping tasks. At low, or zero, forward speeds, the AUV's control surfaces become ineffective. To improve an AUV's low speed maneuverability, while maintaining a low drag profile, through-body tunnel thrusters have become a popular addition to modern AUV systems. The effect of forward vehicle motion and sideslip on these types of thrusters is not well understood. In order to characterize these effects and to adapt existing tunnel thruster models to include them, an experimental system was constructed. This system includes a transverse tunnel thruster mounted in a streamlined AUV. A 6-axis load cell mounted internally was used to measure the thrust directly. The AUV was mounted in Memorial University of Newfoundland's tow tank, and several tests were run to characterize the effect of vehicle motion on the transient and steady state thruster performance. Finally, a thruster model was modified to include these effects.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1994년도 Proceedings of the Korea Automatic Control Conference, 9th (KACC) ; Taejeon, Korea; 17-20 Oct. 1994
• /
• pp.601-604
• /
• 1994

This paper describes an effective method to estimate a position of an automous vehicle equipped with a single CCD-camera along indoor passageways. Using the sequential image data from the self-movement of the vehicle, the position is estimated by integrating the approximated motion parameters. The detection of the yaw angle that is one of the motion parameter is difficult in general, e.g. slip or error for noise, therefore the different detection is presented, which is, without shaft encoders, based on a projection function for 2D-image data and a cross-correlation function so as to be robust for noise. The approximated geometric function to estimate the position is used to reduce the computational effort. To verify the effectiveness of the method, the analysis and the computational results are shown through the simulations. Furthermore, the experimental results by using the test vehicle for the real indoor passageway are shown.

• 로봇학회논문지
• /
• 제15권1호
• /
• pp.32-38
• /
• 2020

This paper describes a method for tracking attitude and position of underwater robots. Underwater work with underwater robots is subject to differences in work efficiency depending on the skill of the operator and the utilization of additional sensors. Therefore, this study developed an underwater robot that can operate autonomously and maintain a certain attitude when working underwater to reduce difference of work efficiency. The developed underwater robot uses 8 thrusters to control 6 degrees of freedom motion, IMU (Inertial Measurement Unit), DVL (Doppler Velocity Log) and PS (Pressure Sensor) to measure attitude and position. In addition, the thruster allocation algorithm was designed to follow the control desired value using 8 thrusters, and the motion control experiments were performed in the engineering water basin using the thruster allocation method.

• Journal of Mechanical Science and Technology
• /
• 제20권8호
• /
• pp.1159-1168
• /
• 2006

In this paper, a new revolute mobile robot arm with five degree of freedom (d.o.f) was developed for autonomous moving robots. As a control system for the robot arm, a distributed control system composed of the main controller and five motor controllers for arm joints was developed. The main controller and the motor controllers w ε re developed using the ARM microprocessor and the TMS320c2407 microprocessor, respectively. A new trajectory tracking algorithm for the motor controllers was devised employing pre-generated off-line trajectory data. Also, a 3-D simulator based on the openGL software to simulate the motion of the robot arm was developed. To validate the performance of the robot system, experiments to track a specified trajectory were performed.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.29-37
• /
• 2008

Vehicle stability is a very important subject in vehicle design and control, because vehicle safety is closely dependent upon its dynamic stability. For the vehicle stability analysis, the nonlinear vehicle model of a mid-size car with three DOF - longitudinal, lateral and yaw - is employed. A rigorous method is used to determine the vehicle stability region in plane motion. An algorithm is used to materialize a topology theorem, which enables to find the exact stability region. A stability criterion for the critical cornering is proposed.

• 한국해양공학회지
• /
• 제29권6호
• /
• pp.488-498
• /
• 2015

This paper presents the dynamic model of an AUV called HW200 for underwater surveillance. The mathematical model of HW200 is briefly introduced, considering its shape. The maneuvering coefficients were initially estimated using empirical formulas and a database of vehicles with similar shapes. A motion simulator, based on Simulink of Mathworks, was developed to evaluate the mathematical model of the vehicle and to tune the maneuvering coefficients. The parameters were finely tuned by comparing the experimental results and simulated responses generated with the simulator by applying the same control inputs as the experiment. The velocity of HW200 in the tuning process was fixed at a constant forward speed of 1.83 m/s. Simulations with variable speed commands were conducted, and the results showed good consistency in the motion response, attitude, and velocity of the vehicle, which were similar to those of the experiment even under the speed variation. This paper also discusses the feasibility of its application to a model-based integrated navigation system (INS) using the auxiliary information on the velocities generated by the model.