• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.66-71
• /
• 2014

Aerodynamic design of a vehicle has very important meaning on the fuel economy, dynamic stability and the noise & vibration of a moving vehicle. In this study, the correlation of aerodynamic effect between two model vehicles moving inline on a road was studied with the basic SAE model vehicle. Drag and lift are two main physical forces acting on the vehicle and both of them directly effect on the fuel economy and driving stability of the vehicle. For the research, the distance between two vehicles is varied from 5m to 30m at the fixed vehicle speed, 100km/h and the side-wind was assumed to be zero. The main issue for this numerical research is on the understanding of the interaction forces; lift and drag between two vehicles formed inline. From the study, it was found that as the distance between two vehicles is closer, the drag force acting on both the front and rear vehicle decreases and the lift force has same trend for both vehicle. As the distance(D) is 5m, the drag of the front vehicle reduced 7.4% but 28.5% for the rear-side vehicle. As the distance is 30m, the drag of the rear vehicle is still reduced to 22% compared to the single driving.

• Journal of Biosystems Engineering
• /
• v.25 no.2
• /
• pp.131-140
• /
• 2000

Spraying operation is one of the most essential in an orchard management and it is also hazardous to human body. for automatic and unmanned spraying , an autonomous travelling vehicle is demanded. In this study, a telemeter was developed using infrared beam which could detect trunks and obstacles measure distance and direction from the vehicle travelling in the orchard. The telemeter system was composed of two infrared LED transmitters and receivers, a beam scanning device for continuous object detection , two rotary encoders for angle detector, and a beam level controller for uneven soil surface. The detected distance and direction signal s were sent to personal computer which made for the system display the angular and distance measurements through I/O board. According to a field test in an apple farm, the system detected up to 10m distance under 12 V of transmitted beam intensity, however, it was recommended that the proper beam transmit intensity be 7 v at the 10 m distance, because of the negative effect to human body at 12 V. The error rate of this system was 0.92 % when the actual distance was compared to measured one. The system was feasible at the small error rate. The developed telemeter system was an important part for autonomous travelling vehicle provided the real time object recognition . A direction control system could be constructed suing the system. It is expected that the system could greatly contribute to the development of autonomous farm vehicle.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.9
• /
• pp.1697-1702
• /
• 2017

This paper proposes a forward vehicle movement estimation algorithm for the image-based forward collision warning. The road region in the acquired image is designated as a region of interest (ROI) and a distance look up table (LUT) is made in advance. The distance LUT shows horizontal and vertical real distances from a reference pixel as a test vehicle position to any pixel as a position of a vehicle on the ROI. The proposed algorithm detects vehicles in the ROI, assigns labels to them, and saves their distance information using the distance LUT. And then the proposed algorithm estimates the vehicle movements such as approach distance, side-approaching and front-approaching velocities using distance changes between frames. In forward vehicle movement estimation test using road driving videos, the proposed algorithm makes the valid estimation of average 98.7%, 95.9%, 94.3% in the vehicle movements, respectively.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.3
• /
• pp.71-76
• /
• 2007

The fatalities of pedestrian account for about 40.0% of all fatalities in Korea 2005. Vehicle-Pedestrian accident generates trajectory of pedestrian. In pedestrian involved accident, the most important data to inspect accident is throw distance of pedestrian. The throw distance of pedestrian can be influenced by many variables. The variables that influence trajectory of pedestrian can be classified into vehicular factors, pedestrian factors, and road factors. Vehicular factors are the frontal shape of vehicle, impact speed of vehicle, the offset of impact point. Many studies have been done about the relation between impact speed and throw distance of pedestrian. But the influence of the offset of impact point was neglected. The influence of the offset of impact point was analyzed by Working Model, and the trajectory of pedestrian, dynamic characteristics of multi-body were analyzed by PC-CRASH, a kinetic analysis program for a traffic accident. Based on the results, the increase of offset reduced the throw distance of pedestrian. However box type vehicle just like bus, the offset of impact point did not influence the throw distance of pedestrian considerably.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.85-90
• /
• 2007

The main function of the Forward Vehicle Collision Warning System (FVCWS) is to warn a driver when he or she experiences dangerous situations caused by a forward vehicle. Warning distance algorithms under same dangerous circumstances are often various depending on automobile manufacturers and component suppliers. Human factors also should be considered to warn the driver at an adequate warning distance. Therefore, it is necessary to develop a system for evaluating the pertinent warning timing in an identically dangerous situation. The system consists of sensors for measuring speed and acceleration of subject vehicle and target vehicle, controllers to follow the velocity profile properly, and wireless telecommunication equipments for receiving or transmitting the measured data in a real-time. According to actual field tests, it is shown that the developed system is suitable to evaluate warning distance of FVCWS.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.741-746
• /
• 2001

This paper presents an investigation of a vehicle-to-vehicle distance control using a Hardware-in-the-Loop Simulation(HiLS) system. Since vehicle tests are costly and time consuming, how to establish a efficient and low cost development tool is an important issue. The HiLS system consists of a stepper motor, an electronic vacuum booster, a controller unit and two computers which are used to form real time simulation and to save vehicle parameters and signals of actuator through a CAN(Controller Area Network). Adoption of a CAN for communication is a trend in the automotive industry. Since this environment is the same as that of a real vehicle, a distance control logic verified in laboratory can be easily transfered to a test vehicle.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.3
• /
• pp.1-9
• /
• 2012

In this paper, we propose a vision-based robust vehicle detection and inter-vehicle distance estimation algorithm for driving assistance system. We use the haar-like features of car rear-shadows, as well as the edge features for detecting of vehicles. The use of additional vehicle edge features greatly reduces the false-positive errors in the vehicle detection. And, after analyzing the conventional two inter-vehicle distance estimation methods: the location-based and the vehicle width-based, an improved inter-vehicle distance estimation algorithm which has the advantage of both method is proposed. Several experimental results show the effectiveness of the proposed method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.104-109
• /
• 2010

The fatality of pedestrian accounts for about 21.2% of all fatality at 2007 year in Korea. In car to pedestrian accident it is very important to inspect the throw distance of pedestrian after collision for exact reconstructing of the accident. The variables that influence on the throw distance of pedestrian can be classified into the factors of vehicle and pedestrian, and road condition. It was simulated by PC-CRASH, a kinetic analysis program for a traffic accident in sedan type vehicle and SPSS program was used for regression analysis. From the results, the throw distance of pedestrian increased with the increasing of vehicle velocity, and decreased with the increasing of impact offset. Also it decreased with the increasing of velocity of pedestrian at accident, and throw distance at the road condition of wet was longer than that at dry condition. Finally, the regression model of sedan type vehicle on the throw distance of pedestrian was as follows; $$dist_i=2.39-0.11offset_i+0.59speed_i-545height_i-0.25walk_i+2.78wet_i+{\epsilon}_i$$.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.6
• /
• pp.1293-1299
• /
• 2012

In this paper, a real-time vehicle detection and tracking algorithms is proposed. The vehicle detection could be processed using GMM (Gaussian Mixture Model) algorithm and mathematical morphological processing with HD CCTV camera images. The vehicle tracking based on separated vehicle object was performed using Euclidean distance between detected object. In more detail, background could be estimated using GMM from CCTV input image signal and then object could be separated from difference image of the input image and background image. At the next stage, candidated objects were reformed by using mathematical morphological processing. Finally, vehicle object could be detected using vehicle size informations dependent on distance and vehicle type in tunnel. The vehicle tracking performed using Euclidean distance between the objects in the video frames. Through computer simulation using recoded real video signal in tunnel, it is shown that the proposed system works well.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1401-1407
• /
• 2002

This paper represents an investigation of the vehicle-to-vehicle distance control system using Hardware-in-the-Loop Simulation(HiLS). Control logic is primarily developed and tested with a specially equipped test vehicle. Establishment of an efficient and low cost development tool is a very important issue, and test vehicle approach is costly and time consuming. HiLS method is useful in the investigation of driver assistance and active safety systems. The HiLS system consists of a stepper motor for throttle control, a hydraulic brake system with an electronic vacuum booster, an electronic controller unit, a data logging computer which are used to save vehicle states and signals of actuator through a CAN and a simulation computer using mathematical vehicle model. Adaptation of a CAN instead of RS-232 Serial Interface for communication is a trend in the automotive industry. Since this environment is the same as a test vehicle, a control logic verified in laboratory can be easily transferred to a test vehicle.