• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.8
• /
• pp.582-594
• /
• 2016

Most studies on hybrid buses are on large-sized buses and not mid-sized low-floor buses. This study uses MATLAB simulation to evaluate the fuel efficiency of such buses powered by diesel. Based on the results, a hybrid electric vehicle system is recommended for the best combination of power and gear ratio. A parallel hybrid system was selected for the hybridization, which transmits front and rear wheel power independently. The necessary power to satisfy the target performance was calculated, and the applicable capacity area was designed. Dynamic programing was used to create and optimize a component sizing algorithm, which was used to scale the capacity of each component of the power source to satisfy the design criteria. The fuel efficiency rate, optimum power source capacity, and gear ratio can be improved by converting a conventional bus into a parallel hybrid bus.

• International Journal of Automotive Technology
• /
• v.4 no.1
• /
• pp.9-19
• /
• 2003

Exhaust emissions were characterized for a fleet of 10 alternative-fuel vehicles (AFVx) including 5 compressed natural gas (CNG) vehicles. 3 liquefied petroleum gas (LPG) vehicles and 2 85% methanol/15% California Phase 2 gasoline (M85) vehicles. In addition to the standard regulated emissions and detailed speciation of organic gas compounds, Fourier Transform Infrared Spectroscopy (FTIR) was used to measure ammonia (NH$_3$) and nitrous oxide ($N_2$O) emissions. NH$_3$, emissions averaged 0.124 g/mi for the vehicle fleet with a range from <0.004 to 0.540 g/mi. $N_2$O emissions averaged 0.022 g/mi over the vehicle fleet with range from <0.002 to 0.077 g/mi. Modal emissions showed that both NH$_3$, and $N_2$O emissions began during catalyst light-off and continued as the catalyst reached its operating temperature. $N_2$O emissions primarily were formed during the initial stages of catalyst light-off. Detailed speciation measurements showed that the principal component of the fuel was also the primary organic gas species found in the exhaust. In particular, methane, propane and methanol composed on average 93%, 79%, and 75% of the organic gas emissions, respectively, for the CNG, LPG. and M85 vehicles.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.11
• /
• pp.570-579
• /
• 2017

In this study, we examined the multi-stage piston-type air compressors typically used in a railroad vehicle, and the heat transfer efficiency was analyzed according to the design conditions of the heat exchanger (a compressor component module for cooling the compressed high temperature air). For the fin-tube heat exchanger used in the most air compressors, numerical analysis was performed to analyze heat transfer by defining the various rectangle tube sizes and the number of fin-per-unit area as design variables under the same flow rate of compressed air. Also, this analysis compared the temperature of the compressed air. Regarding environmental conditions for analysis, the flow rate of the external cooling air was measured and the mean value of the values was applied. And a "turbulence model" was considered in both the external flow of the cooling air and the internal flow inside the tube. From the results of analysis, it was found that the change of the aspect ratio value of the tube greatly influences the heat transfer efficiency of the compressed air, and influences if the fin density is relatively small. As a result, the optimum design specifications of the heat exchanger for air compressors were confirmed based on the analysis of the heat transfer efficiency, according to the design conditions of fin and tube by the operating temperature range of the compressed air.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.5
• /
• pp.1040-1048
• /
• 2016

Recently, the studies of integrated reliability analysis for combat systems are actively progressing. Especially, the research of integrated reliability analysis is emphasized to overcome limitations of the previous studies. In this paper, we propose a calculation technique for integrated hit probability based on front and side hit probabilities that analyzed in previous studies to improve the time-effectiveness. Also, we find out the integrated reliability of each component based on the integrated hit probability which is calculated, and we propose the method which applied the reliability block diagram technique to analyze the whole combat system of the reliability by function kills. For verifying the proposed method, we applied the proposed method to armored fighting vehicle model. The proposed method considers crew which does not considered the element in the previous study and expects to enhance the accuracy of reliability analysis and the time-effectiveness compared with the previous study.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.466-471
• /
• 2014

The interior vehicle noise due to the exterior aerodynamic field is an important topic in the acoustic design of a car. The air flow detached from the A-pillar and impacting the side windows are of particular interest as they are located close to the driver / passenger and provides a lower insulation index than the trimmed car body parts. This paper presents a numerical analysis method for a simplified vehicle model. The internal air cavity including trim component are included in the simulation. The car body includes the windshield and two side windows. The body is made of aluminum and trimmed with porous layers. The methodology proposed in this paper relies on two steps: the first step involves the computation of the exterior flow and turbulence induced non-linear acoustic field using PowerFlow. The second step consists in the computation of the vibro-acoustic transmission through the window using the finite element vibro-acoustic solver Actran. Additionally in order to validate the numerical process, an experimental set-up has been created based on the simplified vehicle. The vibration of the windshield and windows, the total wind noise level results and the relative contributions of the different windows are then presented and compared to measurements. The influence of the flow yaw angle (different wind orientation) is also assessed.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.1
• /
• pp.33-44
• /
• 2003

The atmospheric concentrations of particulate polycyclic aromatic hydrocarbons (PAHs) associated with PM$_{10}$ were determined in Taegu metropolitan area. Sampling was undertaken every five days throughout one year period from 1993 to 1994 at four sites, representing a residential, a commercial, an industrial, and a sub-urban area, respectively. Benzo (e) pyrene, benzo (k) fluoranthene, and chrysene were found to be the most abundant com-pounds during the study period. The concentrations of benzo (a) pyrene, one of carcinogenic PAHs, ranged 2.0~4.8 ng/㎥ in winter and 0.5~1.5 ng/㎥ in summer season, indicating a marked seasonal variation. It was found that there were very similar patterns in the relative profiles of PM$_{10}$-bound PAH concentrations among the four sampling sites, while the absolute levels of each PAH were significantly different from each site. In addition, the patterns of summer to winter concentration ratios for each PAH were almost identical between the different sites. Despite difficulties due to the lack of good markers for specific sources in the target compounds, we were able to evaluate and describe the effects of vehicle emissions and space heatings, using relative profiles of PAHs, winter to summer (W/S) ratios, PAH-to-PAH ratios, and the result of principal component analysis. As a con-sequence, it was concluded that the vehicle emissions in urban and sub -urban areas are likely to be a major contributor for PAH loadings in the ambient atmosphere during the non-heating season, while the contributions of residential heating and local industrial oil burning emissions were highly significant in heating season.son.

• Journal of Multimedia Information System
• /
• v.4 no.4
• /
• pp.195-204
• /
• 2017

Mobile robots are used for years as a valuable research and educational tool in form of available open-platform designs and Do-It-Yourself kits. Rapid development and costs reduction of Unmanned Air Vehicles (UAV) and ground based mobile robots in recent years allowed researchers to utilize them as an affordable research platform. Despite of recent developments in the area of ground and airborne robotics, only few examples of Unmanned Surface Vehicle (USV) platforms targeted for research purposes can be found. Aim of this paper is to present the development of open-design USV drone with integrated multi-level control hardware architecture. Proposed catamaran - type water surface drone enables direct control over wireless radio link, separate development of algorithms for optimal propulsion control, navigation and communication with the ground-based control station. Whole design is highly modular, where each component can be replaced or modified according to desired task, payload or environmental conditions. Developed USV is planned to be utilized as a part of the system for detection and identification of marine and lake waste. Cameras mounted to the USV would record sea or lake surfaces, and recorded video sequences and images would be processed by state-of-the-art computer vision and machine learning algorithms in order to identify and classify marine and lake waste.

• Journal of the Korea Convergence Society
• /
• v.8 no.11
• /
• pp.313-319
• /
• 2017

In this paper, we present a design technique that miniaturises the DC-DC converter, a key component in the electric vehicle system, using the advanced material (Ga-N HEMT) in the LLC resonant converter and freely changes the resonant frequency. This design is also proposed to improve the efficiency and temperature characteristics by adding SR Topology in the secondary side output during the operation of power supply. In this experiment, as a consequence of the constructed circuit with the operation of high switching frequency of 200 kHz, the size of LLC and PFC was able to be minimised by 40[%]. Thus, the characteristics of operating temperature demonstrated $60-65^{\circ}C$ without a heat sink, when the temperature was measured at 250W (12V/20A). The features were all due to the advantages of the change of switching frequency, switching circuits implementation, and the maximisation of switching frequency. Based on these design results, we would like to implement more than 1 [kW].

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.2
• /
• pp.85-91
• /
• 2016

The Positive Temperature Coefficient (PTC) is used for cabin air heating of a battery electric vehicle, which is different from conventional vehicles. Since the PTC heater consumes a large quantity of power in a parasitic manner, many valuable studies have been reported in the field of alternative heat pumps. In this study, a model for an R134a heat pump taking into account the thermal environment of the cabin was developed for a MATLAB/SIMULINK(R) platform. Component and cabin models are validated with reference values. Results show that the heat pump is more competitive for parasitic power consumption over all ambient temperature conditions. Additionally, the method of waste heat recovery to overcome disadvantages when temperatures are below zero is applied to efficiently operate the heat pump.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.5
• /
• pp.349-357
• /
• 2015

The piezoelectric paint sensor is a paint type sensor comprising of an epoxy and piezoelectric powder, which is the main component of a piezoelectric material. This sensor can be easily attached to any type of structure as compared to other sensors because it is viable to directly apply it on structures, as in the case with a typical paint. In this study, the capability of piezoelectric paint sensor for impact detection was evaluated. In Particular, the applications of the piezoelectric paint sensor for railroad vehicles were considered. There have been various cases reported about the damages caused by flying gravel to the under-cover of the railroad vehicle during operation. In order to prevent this, real-time monitoring of the large under-cover surface of the railroad vehicle is unavoidable. Under the assumption of vehicle application, sensor sensitivities were measured after multiple and prolonged exposure to thermal cycle environment $-20{\sim}60^{\circ}C$). Sensitivity evaluation of paint sensor under environmental conditions was conducted in an aluminum specimen. In results, despite the small variations in sensitivity, we could confirm the applicability of this paint sensor for impact detection even after a severe environmental exposure test.