• Geomechanics and Engineering
• /
• 제37권2호
• /
• pp.179-187
• /
• 2024

In this paper, a unified time-dependent constitutive model of Darcy flow and non-Darcy flow is proposed. The influencing factors of flow velocity are discussed, which demonstrates that permeability coefficient is the most significant factor. Based on this, the dynamic evolution characteristics of water inrush during tunneling through fault fracture zone is analyzed under the constant permeability coefficient condition (CPCC). It indicates that the curves of flow velocity and hydrostatic pressure can be divided into typical three stages: approximate high-velocity zone inside the fault fracture zone, velocity-rising zone near the tunnel excavation face and attenuation-low velocity zone in the tunnel. Furthermore, given the variation of permeability coefficient of the fault fracture zone with depth and time, the dynamic evolution of water flow in the fault fracture zone under the variable permeability coefficient condition (VPCC) is also studied. The results show that the time-related factor (α) affects the dynamic evolution distribution of flow velocity with time, the depth-related factor (A) is the key factor to the dynamic evolution of hydrostatic pressure.

• 펄프종이기술
• /
• 제33권1호
• /
• pp.64-72
• /
• 2001

The cigarette ventilation affects not only the amount of tar and nicotine delivery by a cigarette, but also the composition of the smoke. Therefore, it is important to stabilize of variability in cigarette ventilation that would be affected by changes in cigarette components. This work was conducted to determine the major factors that influence the cigarette ventilation and also to provide fundamental informations for improving the uniformity of cigarette performances. To evaluate the effect of cigarette ventilation as a dependant variable, the three independent factors were the air permeability of plugwrap, tipping paper and the filter pressure drop. We determined the effect of paper permeability on ventilation variability and the optimum condition in combinations of independent factors. The mean of cigarette ventilation was increased as plugwrap permeability increases, particularly at 26,000 CU. However, it was exhibited that standard deviation and coefficient of variation of the cigarette ventilation were decreased with increasing plugwrap permeability. At the 600 CU and 1,200 CU of tipping paper permeability, process capability index (Cp) of the cigarette ventilation increased as plugwrap permeability increases. Following the optimum condition of cigarette ventilation induced by fitted regression equation, one was to optimize 50% ventilation level is by combination with plugwrap permeability of 16,000 CU, tipping paper permeability of 810 CU, filter pressure drop of 319 mm$H_2O$, respectively.

• 펄프종이기술
• /
• 제33권1호
• /
• pp.62-62
• /
• 2001

The cigarette ventilation affects not only the amount of tar and nicotine delivery by a cigarette, but also the composition of the smoke. Therefore, it is important to stabilize of variability in cigarette ventilation that would be affected by changes in cigarette components. This work was conducted to determine the major factors that influence the cigarette ventilation and also to provide fundamental informations for improving the uniformity of cigarette performances. To evaluate the effect of cigarette ventilation as a dependant variable, the three independent factors were the air permeability of plugwrap, tipping paper and the filter pressure drop. We determined the effect of paper permeability on ventilation variability and the optimum condition in combinations of independent factors. The mean of cigarette ventilation was increased as plugwrap permeability increases, particularly at 26,000 CU. However, it was exhibited that standard deviation and coefficient of variation of the cigarette ventilation were decreased with increasing plugwrap permeability. At the 600 CU and 1,200 CU of tipping paper permeability, process capability index (Cp) of the cigarette ventilation increased as plugwrap permeability increases. Following the optimum condition of cigarette ventilation induced by fitted regression equation, one was to optimize 50% ventilation level is by combination with plugwrap permeability of 16,000 CU, tipping paper permeability of 810 CU, filter pressure drop of 319 mm$H_2O$, respectively.

• 지질공학
• /
• 제20권1호
• /
• pp.35-45
• /
• 2010

본 연구에서는 10여년 동안 국내 산사태 발생지역 및 인근 미발생지역에서 채취된 자연사면에서의 토층을 대상으로 획득된 약 1,150여개소의 토질시험결과를 토대로 지질조건에 따른 토층의 평균 물성치를 산정하고, 통계적인 분석을 실시하여 지질조건별 투수계수에 대한 간편식을 제안하였다. 투수계수는 화강암지역과 이암지역에서 큰 것으로 나타났으며, 세립토함유량은 이암지역과 편마암지역에서 큰 것으로 나타났다. 지질조건에 따른 토층의 투수계수를 산정하기 위해서 상관성 분석을 실시한 결과 종속변수를 투수계수로 하고 독립변수를 세립토함유량, 함수비, 건조단위중량 및 간극비로 선정하였다. 회귀분석결과 지질조건별 제안된 선형회귀식에서는 공통적으로 세립토함유량 및 간극비가 가장 많이 포함되었다. 제안된 선형회귀식을 검증하기 위하여 타 지역의 토층을 대상으로 수행된 투수계수 측정결과와 선형회귀식으로 예측된 결과를 서로 비교하였다. 비교결과 일부 측정된 결과와 예측된 결과가 차이가 있는 것으로 나타났으나, 그 차이는 비교적 작은 것으로 나타났다. 본 연구에서 제안된 지질조건별 투수계수 산정을 위한 선형회귀식은 국내 지반을 대상으로 적용이 가능할 것으로 판단되나, 추후 지속적인 검증 및 수정이 필요할 것으로 판단된다.

• Geomechanics and Engineering
• /
• 제21권4호
• /
• pp.357-369
• /
• 2020

Different from the conventional planar fracture and simplified Newton model, for power-law slurries with a lower water-cement ratio commonly used in grouting engineering, flow model in geological rough fractures is built based on ten standard profiles from Barton (1977) in this study. The numerical algorithm is validated by experimental results. The flow mechanism, grout superiority, and water plugging of pseudo plastic slurry are revealed. The representations of hydraulic grouting properties for JRCs are obtained. The results show that effective plugging is based on the mechanical mechanisms of the fluctuant structural surface and higher viscosity at the middle of the fissure. The formulas of grouting parameters are always variable with the roughness and shear movement, which play a key role in grouting. The roughness can only be neglected after reaching a threshold. Grouting pressure increases with increasing roughness and has variable responses for different apertures within standard profiles. The whole process can be divided into three stationary zones and three transition zones, and there is a mutation region (10 < JRCs < 14) in smaller geological fractures. The fitting equations of different JRCs are obtained of power-law models satisfying the condition of -2 < coefficient < 0. The effects of small apertures and moderate to larger roughness (JRCs > 10.8) on the permeability of surfaces cannot be underestimated. The determination of grouting parameters depends on the slurry groutability in terms of its weakest link with discontinuous streamlines. For grouting water plugging, the water-cement ratio, grouting pressure and grouting additives should be determined by combining the flow conditions and the apparent widths of the main fracture and rough surface. This study provides a calculation method of grouting parameters for variable cement-based slurries. And the findings can help for better understanding of fluid flow and diffusion in geological fractures.

• 한국농공학회지
• /
• 제13권4호
• /
• pp.2456-2470
• /
• 1971

수수자원(水水資源) 개발(開發)을 위(爲)한 Earth Dam이나 도로(道路)와 같은 흙을 주(主)로하는 많은 구조물축조(構造物築造)에 있어서 그 구조물성질(構造物性質)에 따라서 흙의 종류(種類)가 결정(決定)되며 때로는 흙의 성질(性質)에 따라서 구조물(構造物)의 설계(設計)가 달라진다. 특(特)히 저수(貯水)를 목적(目的)으로 하는 제당축조(堤塘築造)에서 중심점토재료(中心粘土材料)의 선정(選定)은 완전(完全)한 구조물(構造物)을 위(爲)해서 또 공사비(工事費) 절감(節減)을 위(爲)해서 대단(大端)히 중요(重要)한 문제(問題)라 하겠다. 이를 위해서 여러종류(種類)의 흙이 사용(使用)되고 있고 이들 흙의 제반(諸般) 역학적(力學的) 성질(性質)이 이미 실시(實施)된 많은 시험결과(試驗結果)로서 실제(實際) 설계(設計)에, 또 구조물(構造物) 안전도(安全度) 검토(檢討)에 응용(應用)되고 있으나 이들 결과(結果)는 그 흙의 최적함수비(最適含水比) 최대밀도(最大密度)에 대(對)한 것으로 실제(實際) 시공과정(施工過程)에서 볼 때 최과함수상태하(最過含水狀態下)에서 시공(施工)하기는 어려운 것으로 이런 경우(境遇)에 흙의 역학적성질(力學的性質)에 대(對)한 자료(資料)가 없어 설계(設計) 및 안전도(安全度) 검토(檢討)에 지장(支障)이 많은바 이를 위해서 본(本) 시험(試驗)을 실시(實施)하였다. 1. 시험(試驗)에 사용(使用)한 시료(試料)는 실제(實際) 저수지(貯水池) 축제재료(築提材料)로서 사용(使用)하고 있는 재료(材料)를 현장(現場)에서 채취(採取)하였다. 2. 본(本) 시험(試驗)은 농업진흥공사(農業振興公社) 농공시험소(農工試驗所)에서 실시(實施)하였다. 3. 본(本) 시험(試驗) 결과(結果)로서 다음과 같은 점(點)을 실제업무(實際業務)에 응용(應用)할 수 있다. 가. 현장함수비(現場含水比)를 알므로서 공사재료(工事材料)로서의 적부판단(適否判斷)을 내릴수 있다. 나. 함수비(含水比)가 변화시(變化時) 다짐율(率)과 투수계수(透水係數)를 알 수 있으므로 실제설계(實際設計) 및 시공관리(施工管理)에 적용(適用)할수 있다. 다. 시공(施工)된 구조물(構造物)의 다짐율(率)을 알므로서 이에 적합(適合)한 안정도검토(安定度檢討)를 할수 있다. 라. 도로(道路)와 같은 높은 지내력(支耐力)을 요(要)하는 구조물(構造物)을 위(爲)해서는 최적함수비(最適含水比) 내지 건조상태(乾燥狀態)가 좋고 저수지(貯水池)와 같은 지수(止水)를 요(要)하는 구조물(構造物)에서는 최적함수비(最適含水比) 내지 습윤상태(濕潤狀態)로 시공(施工)함이 좋다. 그러나 고소성(高塑性) 흙에서는 지내력(支耐力) 및 지수(止水)를 위해서 공(共)히 후자(後者)의 경우(境遇)가 좋다. 이상(以上)의 연구결과(硏究結果)가 완벽(完璧)하다고는 할수 없으나 본(本) 실험(實驗) 결과(結果)로서 함수비(含水比) 변화(變化)에 대(對)한 제반(諸般) 역학적(力學的) 성질(性質)의 변화상태(變化狀態)를 구(求)하기에 최선(最善)을 하였으므로 이 분야(分野)의 연구자(硏究者)나 설계자(設計者) 또는 시공자(施工者)와 같은 실무자(實務者)에게 다소(多少)의 도움이 된다면 큰영광(榮光)으로 생각 하겠다.