• Journal of Energy Engineering
• /
• v.11 no.2
• /
• pp.114-121
• /
• 2002

Alkali metal compounds existed in original coal or sorbents are exhausted as vapor or small particle at the outlet of combustor when operating PFBC power plant. These compounds can be removed with dust removal equipment, but total generation efficiency will be decreased because of lower operating temperature of dust removal equipment. Alkali metal contained in vapor phase is initially deposited onto turbine blade results in serious corrosion. The concentration of alkali vapor in the PFBC flue gas is 20∼40 ppm which is dependent on mineral characteristics and composition as well as operating condition of PFBC. However, the allowance limit of alkali metal vapor is assigned as less than 50 ppb for gas turbine when coal or oil is used as fuel. Therefore, alkali metal vapor in PFBC or IGCC process should be removed by solid sorbents to prevent corrosion of turbine blade and improve plant efficiency. In the present investigation, powder of Bauxite, Kaolinite and Limestone is used in the preparation of cylinder-type pellet which is inserted into the pressurized alkali removal reactor for the alkali absorption experiment. Experimental results showed that the alkali removal efficiency in the order of Bauxite, Kaolinite and Limestone. Alkali vapor removal efficiency is related with reaction temperature, porosity of pellet and alkali vapor concentration of flue gas.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.4
• /
• pp.901-904
• /
• 2010

Decylthiocyanate (DTC) self-assembled monolayers (SAMs) on Au(111) were prepared by solution and vapor phase deposition methods at $50^{\circ}C$ for 24 h. The formation and surface structure of DTC SAMs were examined using scanning tunneling microscopy (STM). STM imaging revealed that DTC SAMs formed in 1 mM ethanol solution at $50^{\circ}C$ were composed of small ordered domains with lateral dimensions of a few nanometers and disordered phases, whereas DTC SAMs formed in the vapor phase at $50^{\circ}C$ contained two ordered phases: a closely packed c($4{\times}2$) superlattice and a striped phase with an interstripe spacing of 2.6 - 2.8 nm. It was also found that the ordered domain and vacancy island formation for DTC SAMs on Au(111) differs significantly from that of decanethiol SAMs, suggesting that adsorption mechanism is different from each other. From this study, it was confirmed that DTC SAMs with a high degree of structural order can be obtained by vapor phase deposition.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.4
• /
• pp.493-501
• /
• 2004

The principle of vortex tube and cyclone was introduced to enhance the treatment efficiency of waste air streams containing particulate matters, toluene, and others developed by Hangreen Tech, Ltd. and Hoseo Chemical and Industrial Technology R＆D Center. Adsorption, condensation, and/or coagulation could be induced at low temperature zone formed by vortex tube and Joule-Thomson expansion. The pressurized air was introduced at the tangential direction into the cyclone system applied with the coaxial funnel tube. Easily condensible vapors such as toluene. carbon dioxide, and water vapor were adsorbed enforcedly on coagulated or condensed materials which were formed as cores for coagulation or condensation by themselves. These types of coagulation or condensation rates were rapidly promoted as the diameter being growing up. The maximum removal efficiency for carbon dioxide and toluene was achieved to about 87 and 90 percent, respectively. The Joule-Thomson coefficients were increased with the pressure of air injected in the range of the relative humidities between 10% and 30%. An optimum value was observed within the range of the tested temperatures at a fixed pressure. In conclusion. it could be identified that the treatment efficiency would be depended on the pressure of the process air introduced and physical and chemical characteristics of waste air streams containing target materials for a designed system. The final design parameters should be decided depending upon the given system and target materials.

• Journal of the Korean Society of Tobacco Science
• /
• v.27 no.2
• /
• pp.178-188
• /
• 2005

To use the filter materials for selective removal of carbonyl compounds in cigarette mainstream smoke, hydrazine such as 2,4-dinitrophenylhydrazine and dansylhydraznie impregnated adsorbents were prepared with perchloric acid or phosphoric acid as a accelerator in hydrazone formation reaction. The change of morphology of adsorbents in various of impregnator were investigated by SEM. Impregnation amount caused by reaction time, acid type and impregnation reagent, and the adsorption properties of carbonyl compounds in cigarette mainstream smoke were investigated. Amounts of impregnation was increased as increasing reaction time. The removal amount for vapor phase carbonyl compounds by 2,4-DNPH impregnated adsorbent was higher than that of dansylhydrazine impregnated adsorbent. The selectivity of 2,4-DNPH impregnated polyacrylic type adsorbent was superior to those of other adsorbents. This results indicated that the 2,4-DNPH impregnated polyacrylic adsorbent was applicable to cigarette filter material because of its fast reactivity and porosity.

• Food Science of Animal Resources
• /
• v.18 no.4
• /
• pp.285-291
• /
• 1998

Adsorption isotherms of water vapour for infant formula milk powders manufactured by P. M. and N company in Korea were measured at temperatures between 20, 30 and 40$^{\circ}C$ using COST-90 modified method. Results showed that the isotherms were sigmoidal in shape. The adsorption isotherms of milk powder were depending on the temperature and products. The BET-model were applied and analyzed to compare the experimental value. It was found that the BET-model is fitted with measuring data. Sample P showed the lowest monolayer value and sample N showed the highest. Isosteric heat obtained upon application of BET-model was calculated in this field of temperature using the Clausius-Clapeyron equation. It is suggested that the usage of the BET-model to estimate the heat of water sorption in infant formula milk powder should be in agreement with the results from COST-90 project.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.4
• /
• pp.37-42
• /
• 1994

The adsorption of water vapor and equilibrium moisture content(EMC) of the specimens for four softwood species dried by conventional- and high temperature method and equilibrated to 15% of the target EMC condition at 25$^{\circ}C$ were determined by oven drying method and with moisture meters. The amount of adsorption for high temperature dried red pine was significantly higher than that of conventional kiln dried wood, while those of eastern white pine, eastern hemlock and Norway spruce were not significantly different between drying methods. EMCs of these four species determined by oven drying method and with capacitive admittance moisture meter were not significantly different between drying methods. EMC of high temperature dried red pine determined with resistance moisture meter was significantly higher than that of conventional kiln dried wood. But EMCs of other species did not show significant difference between drying methods. EMCs of conventional and high-temperature dried wood determined with electronic moisture meters, especially in the case of the capacitive-admittance moisture meter measurement, were lower than that determined by oven drying method.

• Journal of the Korean Vacuum Society
• /
• v.22 no.5
• /
• pp.225-230
• /
• 2013

Cryopump removes gas molecules by condensation and adsorption. Therefore, cryo-surface temperature and corresponding vapor pressure influence directly the pumping performance. If the surface temperature of any part is neither low nor high, there occurs the desorption of gas molecules condensed or adsorbed, and the emitted molecules can be captured again, which leads to a time-consuming and fluctuating change of the pressure. Though every gas can show such a pressure instability at a specified temperature range, the instability generated in a sputter system using Ar as a working gas and operating with a cryopump is especially undesirable. In this paper the cause of the argon instability is analyzed and corrective is provided through the measurement of the Ar recovery time.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.70-75
• /
• 2010

Compressed air represents an energy source and an force-transmission medium for brake systems on medium-heavy and heavy-duty commercial vehicles. However, one disadvantage is the tendency of air to absorb moisture in the form of water vapor. This water vapor condenses once the air, which is heated during compression, cools back to ambient temperature upon emerging from the air compressor. The resulting condensation assumes the form of moisture in pneumatic lines, air tanks, cylinders and valve assemblies and can have negative consequences for the brake system and vehicle safety. The pneumatic systems on today's vehicles are equipped with air dryers, in which the supplied air is dried according to the adsorption principle. In the systems, the compressed air flows through a granular desiccant with molecular sieves which captures the water molecules.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.4
• /
• pp.65-70
• /
• 2006

Carbon nanotubes (CNT) grown by chemical vapor deposition (CVD) and plasma enhanced chemical vapor deposition (PECVD), and followed by annealing at $400{\sim}500^{\circ}C$ were investigated for gas sensing under 1.5ppm $NO_{2}$ concentration at an operating temperature of $200^{\circ}C$. The electrical resistance of CNT sensor decreased with temperature, indicating a semiconductor type. The resistance of CNT sensor decreased with $NO_{2}$ adsorption. It was found that the sensitivity of sensor was affected by humidity and decreased under microwave irradiation for 3 minutes. The CNT sensor grown by PECVD had a higher sensitivity than that of CVD.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.619-623
• /
• 2006

Selective vapor deposition of conductive poly(3,4-ethylenedioxythiophene) (PEDOT), thin films has been carried out on self assembled monolayers patterned oxide substrate. Since the 3,4-ethylenedioxythiophene(EDOT) monomer can be polymerized only in the presence of oxidant such as $FeCl_3$, the PEDOT thin film is selectively deposited on patterned $FeCl_3$, which only adsorbs on the partly removed SAMs region due to the inability of $FeCl_3$ to adsorb on SAMs. Therefore, the partly removed SAMs can act as an adsorption layer for the $FeCl_3$ and also as a glue layer for the deposition of PEDOT, resulting in the significantly increased adhesion of PEDOT to $SiO_2$ substrate. The use of UV lithography and Cr patterned quartz mask provided the formation of SAMs patterns on oxide substrates, which allowed for the selective deposition of conductive PEDOT thin films.$^{oo}The$ new process was successfully developed for the selective deposition of PEDOT thin films on SAMs patterned oxide substrate, providing a new way for the patterning of vapor phase deposition of PEDOT thin films with accurate alignment and addressing the inherent adhesion issues between PEDOT and dielectrics.