• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.108-114
• /
• 2002

Red pine(Pinus densiflora) square timbers with 14.0 cm and 16.5 cm of face size and 24 m long were dried in a vacuum-press kiln and in a radio-frequency/vacuum(RF/V) kiln to compare drying rate, moisture content(MC) distribution and specific energy. RF/V drying rate was higher than vacuum-press drying rate. The effect of size of cross section on the RF/V drying rates were more pronounced than those of vacuum-press drying. The longitudinal- and the transverse MC distribution of dried square timber showed convex profile for the vacuum-press drying and concave profile for the RF/V drying. Moisture gradient of width direction was similar to the thickness direction in vacuum-press dried square timber and was more slight than that of the thickness direction in the RF/V dried large square timber. The specific energy consumption curve increased as MC decreased. Specific energy(kWh/kg of water evaporated) of the vacuum-press process required more than that of the RF/V process.

• Journal of the Korea Furniture Society
• /
• v.10 no.2
• /
• pp.29-36
• /
• 1999

During a radio-frequency/vacuum plus press drying process of some hardwood veneers for decoration we investigated the effect of a grain and thickness of a veneer sheet on drying rates, variations of final moisture content within a bundle of veneer sheets, and formation of checking, end waving, and burning mark. About thirty three hundreds sheet of veneer could be dried in sixty five hours from green to in0-use moisture content, and a final moisture content was significantly effected by initial moisture content of veneer. There were nearly variations in a final moisture content among the veneer sheets in the same bundle. A checking was never found in a edge-sliced veneer, and very slight in a flat-sliced veneer of ash and red oak. There were no end waving and no burning mark in all veneer sheets.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.1
• /
• pp.1-8
• /
• 2001

Red pine (Pinus densiflora), white pine (Pinus koraiensis), larch (Larix leptolepis) and Western hemlock (Tsuga heterophylla) lumber were vacuum-press dried under three drying schedules to investigate current moisture contents (MC), drying rates and drying time factors related to five lumber thicknesses of 3, 5, 7, 9 and 11cm. Current MC could be estimated by drying factors such as lumber thickness, initial Me and drying time. Average drying rate from 30% to 15% Me was the highest for Western hemlock below fiber satuartion point, red pine, white pine and larch in the order of their magnitude. Drying rate curvilinearly decreased as lumber thickness increased. Drying time factor curvilinearly increased as lumber thickness increased.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.1
• /
• pp.9-15
• /
• 2001

Specific energy curves for water removal in vacuum-press drying of different thick softwoods of red pine (Pinus densiflora), white pine (Pinus koraiensis), larch (L. leptolepis) and Western hemlock (Tsuga heterophylla) were split into three sections: increased slowly, fairly constant, and increased rapidly. Calculated specific energy for 3, 5, 7, 9 and 11cm thick lumber was a value of 0.483, 0.649, 0.814, 0.977 and 1.138kWh/kg of water, respectively. Specific energy almost linearly increased as lumber thickness increased, and specific energy for severe schedule was less than that for mild schedule. Average specific energy was 0.712kWh/kg and vacuum-press drying consumed less energy as compared with any other drying methods.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.39-48
• /
• 1993

End-matched disks of 7.7cm thickness were part-time dried in vacuum press dryer to investigate the drying characteristics by using drying schedules and end treatments. The ginkgo disks could be dried faster with severer end checks and ring failures by C schedule than by S schedule. There were no significant differences in drying rates and amounts of end checks, ring failures and V-shaped checks occurred between ginkgo disks end-taped with Korean traditional paper (KTP) and those untreated. The drying time of walnut disks was slightly reduced by end-taping with KTP. And the length of end checks and V-shaped checks and the frequency of defected disk were decreased more effectively than those untreated. The tangential strains and tangential drying stresses near bark sides of ginkgo and walnut disk untreated were developed in the early stage of drying and incresed slightly curvi-linearly above fiber saturation point (fsp) and more curvi-linearly below fsp. The influence of end-taping with KTP on the drying rate for impermeable walnut disk was stronger than that for permeable ginkgo disk.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1256-1256
• /
• 2001

The physico-chemical and texture characteristics of meat determine the nutritional, technological and sensory quality. However, the analysis of meat quality requires expensive, laborious and time consuming analytical methods. The objective of this study was to evaluate NIR spectroscopy using transmittance for determining the moisture, fat, protein and total pigment content, the water holding capacity (WHC) and the toughness of beef meat. A total of 318 spectra were recorded from ground beef samples by a Feed Analyzer 1265 of Infratec. The samples were obtained from the Longissimus muscle of the 10$^{th}$ rib of yearling bulls, ground with an electrical chopper, vacuum packaged, aged during 7 days and frozen at -24$^{\circ}C$ until the analyses were done. Moisture content was measured by oven drying at 10$0^{\circ}C$, fat content was determined by Soxhlet extraction and protein content was estimated from nitrogen content using the Kjeldahl analysis. The total pigment content was determined by the method of Hornsey and the WHC using the method of filter paper press. The instrumental evaluation of texture (maximum load WB, maximum stress MS and toughness) was conducted in an Instron equipment with a Warner-Bratzler shearing device. This analysis was performed on a chop of 3.5 cm obtained from the longissimus of the 8$^{th}$ rib, aged during 7 days, kept frozen at -24$^{\circ}C$ and cooked before the analysis. Near infrared spectra were recorded as log 1/T (T=transmittance) at 2 nm intervals from 850 to 1050 nm using a Feed Analyzer 1265 of Infratec. Calibrations were performed with the WinISI software (vs. 1.02) using the MPLS method. To examine the effect of scatter correction o. derivation of spectra on the calibration performance, calibrations were calculated with the crude spectra or pretreated with different mathematical treatments (inverse MSC, SNVD) and/or second derivative operation. For chemical composition, the use of the scatter corrections improved the calibration statistics, in terms of lower SECV and higher $r^2$. In most of the variables, the use of the 2$^{nd}$ derivative improved the predictions, mainly when combined with the SNVD treatment. However, for predicting the texture traits, the best estimation was obtained from the crude spectrum. These results showed that the equations obtained for predicting moisture, fat and total pigments were very accurate, with $r^2$ being higher that 0.9. However, the prediction of the texture traits (WB, MS, toughness) from ground meat was poor.