• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.44-50
• /
• 2001

Metal oxide semiconductor (MOS) structures containing nanocrystals are fabricated by using rapid thermal oxidations of amorphous silicon films. The amorphous films are deposited either by electron beam deposition method or by electron beam deposition assisted by Ar ion beam during deposition. Post oxidation of e-beam deposited film results in relatively small hysteresis of capacitance-voltage (C-V) and the flat band voltage shift, $\DeltaV_{FB}$ is less than 1V indicative of the formation of low density nanocrystals in $SiO_2$ near $SiO_2$/Si interface. By contrast, we observe very large hysteresis in C-V characteristics for oxidized ion-beam assisted e-beam deposited sample. The flat band voltage shift is larger than 22V and the hysteresis becomes even broader as increasing injection times of holes at accumulation condition and electrons at inversion condition. The result indicates the formation of slow traps in $SiO_2$ near $SiO_2$/Si interface which might be related to large density nanocrystals. Roughly estimated trap density is $1{\times}10^{13}cm^{-2}$. Such a large hysteresis may be explained in terms of the activation of adatom migration by Ar ion during deposition. The activated migration may increase nucleation rate of Si nuclei in amorphous Si matrix. During post oxidation process, nuclei grow into nanocrystals. Therefore, ion beam assistance during deposition may be very feasible for MOS structure containing nanocrystals with large density which is a basic building block for single electron memory device.

• Journal of the Korean Vacuum Society
• /
• v.20 no.6
• /
• pp.395-402
• /
• 2011

The nanomechanical properties of fully lithiated and unlithiated silicon nanowire deposited on silicon substrate have been studied with atomic force microscopy. Silicon nanowires were synthesized using the vapor-liquid-solid process on stainless steel substrates using Au catalyst. Fully lithiated silicon nanowires were obtained by using the electrochemical method, followed by drop-casting on the silicon substrate. The roughness, derived from a line profile of the surface measured in contact mode atomic force microscopy, has a smaller value ($0.65{\pm}0.05$ nm) for lithiated silicon nanowire and a higher value ($1.72{\pm}0.16$ nm) for unlithiated silicon nanowire. Force spectroscopy was utilitzed to study the influence of lithiation on the tip-surface adhesion force. Lithiated silicon nanowire revealed a smaller value (~15 nN) than that of the Si nanowire substrate (~60 nN) by a factor of two, while the adhesion force of the silicon nanowire is similar to that of the silicon substrate. The elastic local spring constants obtained from the force-distance curve, also shows that the unlithiated silicon nanowire has a relatively smaller value (16.98 N/m) than lithiated silicon nanowire (66.30 N/m) due to the elastically soft amorphous structures. The frictional forces of lithiated and unlithiated silicon nanowire were obtained within the range of 0.5-4.0 Hz and 0.01-200 nN for velocity and load dependency, respectively. We explain the trend of adhesion and modulus in light of the materials properties of silicon and lithiated silicon. The results suggest a useful method for chemical identification of the lithiated region during the charging and discharging process.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.6
• /
• pp.33-40
• /
• 2008

Normally, cedar heartwood has a red color. However, it frequently changes black color (blackening phenomenon). It is reported that blackening phenomenon of cedar has been caused by oxidation of phenolics and norlignan extractives under weak alkaline conditions. In this study, heat treatment and UV irradiation were carried out to reduce the difference of color value between blackened wood and bright sap wood. Effects of temperature, moisture content, treatment time and light on decrease of color difference between blackened heartwood and sapwood were evaluated in each treatment. A decrement of different color value between blackened heartwood and bright sapwood by hot-water treatment was bigger than others. An effect of the vacuum drying was similar to that of the kiln drying. UV irradiation decreases the color difference between dried blackened heartwood and bright sapwood. It is suggested that UV irradiation could be used as final treatment to reduce the color difference on wood during drying process. Determination of optimum conditions and development of hybrid process for control of discoloration will be needed in a further study.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.2
• /
• pp.115-120
• /
• 2000

All solid-state thin film micro-batteries consisting of lithium metal anode, an amorphous LiPON electrolyte and cathode of vanadium oxide have been fabricated and characterized, which were fabricated with cell structure of $Li/LiPON/V_2O_5Pt$. The effect of various oxygen partial pressure on the electrochemical properties of vanadium oxide thin films formed by d.c. reactive sputtering deposition were investigated. The vanadium oxide thin film with deposition condition of $20\%\;O_2/Ar$ ratio showed good cycling behavior. In in-siか process, the LiPON electrolyte was deposited on the $V_2O_5$ films without breaking vacuum by r.f. magnetron sputtering at room temperature. After deposition of the amorphous LiPON, the Li metal films were grown by a thermal evaporator in a dry room. The charge-discharge cycle measurements as a function of current density and voltage variation revealed that the $Li/LiPON/V_2O_5$ thin film had excellent rechargeable properly when current density was $7{\mu}A/cm^2$. and cut-off voltage was between 3.6 and 2.7V In practical experiment, a stopwatch ran on this $Li/LiPON/V_2O_5$ thin film micro-battery. This result means that thin film micro-battery fabricated by in-siか process is a promising for power source for electronic devices.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.127.1-127.1
• /
• 2011

In this paper, ZnO:Al thin films with c-axis preferred orientation were prepared on Soda lime glass substrates by RF magnetron sputtering technique. AZO thin film were prepared in order to clarify optimum conditions for growth of the thin film depending upon process, and then by changing a number of deposition conditions and substrate temperature conditions variously, structural and electrical characteristics were measured. For the manufacture of the AZO were vapor-deposited in the named order. It is well-known that post-annealing is an important method to improve crystal quality. For the annealing process, the dislocation nd other defects arise in the material and adsorption/decomposition occurs. The XRD patterns of the AZO films deposited with grey theory prediction design, annealed in a vacuum ambient($2.0{\times}10-3$Torr)at temperatures of 200, 300, 400 and $500^{\circ}C$ for a period of 30min. The diffraction patterns of all the films show the AZO films had a hexagonal wurtzite structure with a preferential orientation along the c-axis perpendicular to the substrate surface. As can be seen, the (002)peak intensities of the AZO films became more intense and sharper when the annealing temperature increased. On the other hand, When the annealing temperature was $500^{\circ}C$ the peak intensity decreased. The surface morphologies and surface toughness of films were examined by atomic force microscopy(AFM, XE-100, PSIA). Electrical resistivity, Gall mobility and carrier concentration were measured by Hall effect measuring system (HL5500PC, Accent optical Technology, USA). The optical absorption spectra of films in the ultraviolet-visibleinfrared( UV-Vis-IR) region were recorder by the UV spectrophotometer(U-3501, Hitachi, Japan). The resistivity, carrier concentration, and Hall mobility of ZnS deposited on glass substrate as a function of post-annealing.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.11
• /
• pp.1025-1032
• /
• 2009

This study investigated a possibility to develop an adsorption process for volatile organic compounds (VOCs) of the solvent emitted during dry cleaning. Pitch activated carbon fiber (ACF) was chosen as an adsorbent of VOCs, and an electric swing adsorption process was utilized for the reproduction of the adsorbent after the completion of VOCs adsorption. Effects of ACF types and several solvents such as trichloroethylene (TCE) and toluene were examined on breakthrough curves and amounts of adsorbed VOCs. ACF was pretreated under various conditions in order to enhance the amounts of the adsorbed VOCs. Temperatures and voltages were measured for the reproduction of the ACF after full adsorption. ACF having micropores exhibited high adsorption of TCE, and high surface area of ACF could increase the adsorption property of toluene. In general, ACF could adsorb 41~54% TCE of the adsorbent weight. The increase of inlet VOCs concentration significantly decreased the breakthrough time and slightly lowered the amounts of adsorbed VOCs. Thus, ACF could effectively adsorb VOCs in low concentration in the feed stream. ACF pretreated by heat under vacuum showed excellent toluene adsorption with controlling oxygen functional groups on the ACF surface, which revealed that vacant carbon site could be the adsorption point of toluene. Most adsorbed toluene was desorbed at $150^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.420-424
• /
• 2016

In this study, we developed photocatalytic technology to address the emerging serious problem of air pollution through indoor air cleaning. A single layer of $WO_3$ was prepared by using the dry process of general RF magnetron sputtering. At a base vacuum of $1.8{\times}10^{-6}$[Torr], the optical and electrical properties of the resulting thin films were examined for use as a transparent electrode as well as a photocatalyst. The single layer of $WO_3$ prepared at an RF power of 100 [W], a pressure of 7 [mTorr] and Ar and $O_2$ gas flow rates of 70 and 2 sccm, respectively, showed uniform and good optical transmittance of over 80% in the visible wavelength range from 380 [nm] to 780 [nm]. The optical catalyst characteristics of the $WO_3$ thin film were examined by investigating the optical absorbance and concentration variance in methylene blue, where the $WO_3$ thin film was immersed in the methylene blue. The catalytic characteristics improved with time. The concentration of methylene blue decreased to 80% after 5 hours, which confirms that the $WO_3$ thin film shows the characteristics of an optical catalyst. Using the reflector of a CCFL (cold cathode fluorescent lamp) and the lens of an LED (lighting emitting diode), it is possible to enhance the air cleaning effect of next-generation light sources.

• Journal of Technologic Dentistry
• /
• v.36 no.3
• /
• pp.141-147
• /
• 2014

Purpose: Dental casting #Gr I (Co-25Cr-5Mo-3Sn-1Mn-1Si), #Gr II (Co-25Cr-5Mo-5Cu-1Mn -1Si) and #Gr III (Co-25Cr-5Mo-3Sn-5Cu-1Mn-1Si) master alloys of granule type were manufactured the same as manufacturing processes for dental casting Ni-Cr and Co-Cr-Mo based alloys of ingot type. These alloys were analyzed melting processes with heating time of high frequency induction centrifugal casting machine using infrared thermal image analyzer. Methods: These alloys were manufactured such as; alloy design, the first master alloy manufatured using vacuum arc casting machine, melting metal setting in crucible, melting in VIM, pouring in the mold of bar type, cutting the gate and runner bar and polishing. These alloys were put about 30g/charge in the ceramic crucible of high frequency induction centrifugal casting machine and heat, Infrared thermal image analyzer indicated alloys in the crucible were set and operated. Results: The melting temperatures of these alloys measuring infrared thermal image analyzer were decreased in comparison with remanium$^{(R)}$ GM 800+, vera PDI$^{TM}$, Biosil$^{(R)}$ f, WISIL$^{(R)}$ M type V, Ticonium 2000 alloys of ingot type and vera PDS$^{TM}$(Aabadent, USA), Regalloy alloys of shot type. Conclusion: Co-Cr-Mo based alloy in addition to Sn(#Gr I alloy) were decreased the melting temperature with heating time of high frequency induction centrifugal casting machine using infrared thermal image analyzer.

• Resources Recycling
• /
• v.15 no.5 s.73
• /
• pp.26-32
• /
• 2006

The waste solution discharged from the LCD manufacturing process contains acids like nitric, acetic and phosphoric acid and metal ions such as Al, Mo and other impurities. It is important to remove impurities less than 1 ppm in phosphoric acid to reuse as an etchant because the residual impurities even in sub-ppm concentration in semiconductor materials play a major role on the electronic properties. In this study, a mixed system of solvent extraction, diffusion dialysis and ion-exchange was developed to commercialize in an efficient system fur recovering the high-purity phosphoric acid. By vacuum evaporation, almost 99% of nitric and acetic acid was removed. And by solvent extraction method with tri-octyl phosphate (TOP) as an extractant, the removal of acetic and nitric acid from the acid mixture was achieved effectively at the ratio A/O=1/3 with 4th stage of extraction stage. About 97.5% of Al and 36.7% of Mo were removed by diffusion dialysis. Essentially almost complete removal of metal ions and purification of high-purity phosphoric acid could be obtained by using ion exchange.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.1
• /
• pp.15-19
• /
• 2012

Tris(8-quinolinolato)aluminum(III); $Alq_3$ has been frequently used as an electron transporting layer in organic light-emitting diodes. Either Ba with a low work function or Au with a high work function was deposited on $Alq_3$ layer in vacuum. And then, the behaviors of electron transition at the $Alq_3$/Ba and $Alq_3$/Au interfaces were investigated by using the near edge x-ray absorption fine structure (NEXAFS) spectroscopy. In the each interface, the energy levels of unoccupied obitals were assigned as ${\pi}^*$(LUMO, LUMO+1, LUMO+2 and LUMO+3) and ${\sigma}^*$. And the relative intensities of these peaks were investigated. In an oxygen atom composing $Alq_3$ molecule, the relative intensities for a transition from K-edge to LUMO+2 were largely increased as Ba coverage (${\Theta}_{Ba}$, 2.7 eV) with a low work function was in-situ sequentially increased on $Alq_3$ layer. In contrast, the relative intensities for the LUMO+2 peak were reduced as Au coverage (${\Theta}_{Au}$, 5.1 eV) with a high work function were increased on $Alq_3$ layer. This means that the electron transition by photon in oxygen atom which consists in the unoccupied orbitals in $Alq_3$ molecule, largely depends on work function of a metal. Meanwhile, in the case of electron transition in a carbon atom, as ${\Theta}_{Ba}$ was increased on $Alq_3$, the relative intensity from K-edge to ${\pi}_1{^*}$ (LUMO and LUMO+1) was slightly decreased, and from K-edge to ${\pi}_2{^*}$ (LUMO+2 and LUMO+3) was somewhat increased. This rising of the energy state from ${\pi}_1{^*}$ to ${\pi}_2{^*}$ exhibits that electrons provided by Ba would contribute to the process of electron transition in the $Alq_3$/Ba interfaces. As shown in above observation, the analyses of NEXAFS spectra in each interface could be important as a basic data to understand the process of electron transition by photon in pure organic materials.