• Journal of the Korean Ceramic Society
• /
• v.35 no.7
• /
• pp.685-690
• /
• 1998

The wetting behavior and the characteristic of spontaneous infiltration of pure Al and Al-(Si)-Mg alloys on {{{{ { {Al }_{ 2} O}_{3 } }} in vacuum argon and nitrogen atmosphere were investigated to find out the spontaneous in-filtration mechanism. The wetting of molten Al and Al alloys on {{{{ { {Al }_{ 2} O}_{3 } }} was only possible in cacuum at-mosphere but the sponataneous infiltration of molten Al-(Si)-Mg alloys was successfully made on {{{{ { {Al }_{ 2} O}_{3 } }} pre-form in nitrogen atmoshpere. The difference of wettability and spontaneous infiltration of molten Al and Al alloys on {{{{ { {Al }_{ 2} O}_{3 } }} were found to be related to formation of the Mg-N compound coated layer on {{{{ { {Al }_{ 2} O}_{3 } }} particles which was believd to increase wettability of molten Al alloys on {{{{ { {Al }_{ 2} O}_{3 }.

• KSBB Journal
• /
• v.23 no.5
• /
• pp.460-462
• /
• 2008

Pollens grains collected from fully dehisced lily (Lilium longiflorum) anthers were given wounds by means of shaking in the presence of aluminum oxide particles. They were transformed by infiltration with Agrobacterium cells harboring a synthetic DNA encoding signal peptide-fused epidermal growth factor (EGF). After incubation for 24 hr in vitro, the pollen culture showed that EGF mRNAs and proteins were successfully expressed in the analysis of cDNA blot hybridization and immuno-blotting.

• Journal of Powder Materials
• /
• v.7 no.2
• /
• pp.102-109
• /
• 2000

With the emergence of the 3D CAD, it is possible to create a physical part directly from a digital model by accumulating layers of a given material. The technology is being widely used for checking designs, to create master models for rapid tooling, and for reverse engineering. However, in general, a model created by rapid prototyping technology is made of soft material that cannot be used as mass prouduction hard tool. Newly developed powder casting is suitable for rapid-manufacturing metallic tools. Powder casting can serve as a promising rapid tooling method because of high density characteristics and low dimensional shrinkage below 0.1% during sintering and infiltration. Through this process, we have realized significant time and cost savings eliminating the expense of conventional prototype tooling process.

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.399-406
• /
• 1994

The SiC/MoSi2 composite material was prepared by infiltration with the mixture of metal Si and MoSi2 into the preform of $\alpha$-SiC and graphite under the vacuum atmosphere of 10-1 torr. The mechanical properties, phases and microstructural characteristics have been investigated by employing an universal testing machine, scanning electron microscope and X-ray diffractometer. With the increase of MoSi2/Si mixing content, the quantity of the residual silicon phase was decreased and the hardness and fracture toughness of composite materials were increased. Also, as the infiltration temperature increased, a lot of fine-grained $\beta$-SiC phases, which were produced from the reaction of graphite and liquid silicon melt, were transformed to $\alpha$-SiC phases.

• Journal of Plant Biotechnology
• /
• v.32 no.4
• /
• pp.275-279
• /
• 2005

Tah tasai chinese cabbage (Brassica campestris var. narinosa), a vegetable plant popularly consumed as several-days-old seedlings in oriental countries, can be easily cultivated using a simple appliance. We demonstrated that Agrobacterium-mediated transformation via vacuum infiltration (agroinfiltration) resulted in a successful transient GUS gene expression in tah tasai chinese cabbage seedlings. Pre-germinated seeds were found to be more susceptible to Agrobacterium infection than one-day-old or two-days-old seedlings. We also demonstrated that hydrogen peroxide (HPO) treatment increased GUS expression especially for two-days-old seedlings. In ELISA using seedlings transformed with hepatitis B surface antigen (HBsAg) DNA by agroinfiltration, HBsAg protein synthesis increased more than two folds by HPO treatment to two-days-old seedlings in comparison to the mock-treated pre-germinated seeds.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.485-490
• /
• 2010

In our previous studies, continuous SiC fiber-reinforced SiC-matrix composites ($SiC_f$/SiC) had been fabricated by two different slurry infiltration methods: vacuum infiltration and electrophoretic deposition (EPD). 12 wt% of $Al_2O_3-Y_2O_3$-MgO with respect to SiC powder was used as additives for liquid-phase assisted sintering. After hot pressing at $1750^{\circ}C$ under 20 MPa for 2 h in Ar atmosphere, a high composite density could be achieved for both cases, whereas the problems such as large grain size and non-uniform distribution of liquid phase were observed, which was resulted in the relatively poor mechanical properties of composites. Therefore, efforts have been made to reduce the grain growth during the sintering, including the optimization for hot pressing condition and utilization of spark plasma sintering using a SiC monolith. Based on the results, spark plasma sintering was found to be effective method in decreasing the amount of sintering additive, time and grain growth, which will be explained in comparison to the results of hot pressing in this paper.

• Journal of Powder Materials
• /
• v.5 no.3
• /
• pp.199-209
• /
• 1998

A new low melting inorganic binder, monoclinic $HBO_2$, has been developed for Selective Laser Sintering (SLS) of alumina powder by dehydration process of boron oxide powder in a vacuum oven at $120^{\circ}C$. It led to better green SLS parts and higher bend strength far green and fired parts compared to other inorganic binders such as aluminum and ammmonium phosphate. This appeared to be due to its low viscosity and better wettability of the alumina particle surface. A low density single phase ceramic, aluminum borate ($Al_{18}B_4O_{33}$), and multiphase ceramic composites, $A_{12}O_3-A_{14}B_2O_9$, were successfully developed by laser processing of alumina-monoclinic $HBO_2$ powder blends followed by post-thermal processing; both $Al_{18}B_4O_{33}$ and $A_{14}B_2O_9$ have whisker-like grains. The physical and mechanical properties of these SLS-processed ceramic parts were correlated to the materials and processing parameters. Further densification of the $A_{12}O_3-A_{14}B_2O_9$ ceramic composites was carried out by infiltration of colloidal silica, and chromic acid into these porous SLS parts followed by heat-treatment at high temperature ($1600^{\circ}C$). The densities obtained after infiltration and subsequent firing were between 75 and 80% of the theoretical densities. The bend strengths are between 15 and 33 MPa.

• Korean Journal of Materials Research
• /
• v.22 no.6
• /
• pp.309-315
• /
• 2012

Metal foam has many excellent properties, such as light weight, incombustibility, good thermal insulation, sound absorption, energy absorption, and environmental friendliness. It has two types of macrostructure, a closed-cell foam with sealed pores and an open-cell foam with open pores. The open-cell foam has a complex macrostructure consisting of an interconnected network. It can be exploited as a degradable biomaterial and a heat exchanger material. In this paper, open cell Mg alloy foams have been produced by infiltrating molten Mg alloy into porous pre-forms, where granules facilitate porous material. The granules have suitable strength and excellent thermal stability. They are also inexpensive and easily move out from open-cell foamed Mg-Al alloy materials. When the melt casting process used an inert gas, the molten magnesium igniting is resolved easily. The effects of the preheating temperature of the filler particle mould, negative pressure, and granule size on the fluidity of the open cell Mg alloy foam were investigated. With the increased infiltration pressure, preheat temperature and granule sizes during casting process, the molten AZ31 alloy was high fluidity. The optimum casting temperature, preheating temperature of the filler particle mould, and negative pressure were $750^{\circ}C$, $400-500^{\circ}C$, and 5000-6000 Pa, respectively, At these conditions the AZ31 alloy had good fluidity and castability with the longest infiltration length, fewer defects, and a uniform pore structure.

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.301-308
• /
• 2003

Glass-infiltrated alumina, which can be used as an all-ceramic dental crown, was prepared. The glasses in the system of SiO$_2$-B$_2$O$_3$-Al$_2$O$_3$-CaO-La$_2$O$_3$with various amount of $Al_2$O$_3$infiltrated into a porous sintered alumina. The effect of $Al_2$O$_3$on the infiltration characteristics and its mechanical strength were studied. The corrosion of the sintered alumina by infiltrated glasses was prevented by increasing the amount of $Al_2$O$_3$in the glass batches, this increased the bending strength of the glass infiltrated alumina composite. The crack like voids in the sintered alumina was a cause of the deteriorating the mechanical strength of the composite, and this can be eliminated by sintering the alumina at 130$0^{\circ}C$. Glass infiltration under the vacuum atmosphere enhanced the hording strength of the composite up to 453$\pm$31 MPa.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1069-1073
• /
• 2002

Properties of $B_4C/Al$ cermets were studied as a function of atmosphere during infiltration and post-heat treatment. The cermet A(infiltrated at $1100{\circ}C$/10 min under vacuum) had 19.4 wt% of Al but the cermet B(infiltratd at $1080{\circ}C$/10 min under a flowing argon) showed 14.4 wt% of Al. It indicated that the reaction between $B_4C$ and Al underwent slower under vacuum than under a flowing argon. The cermet B as infiltrated showed the density of 2.65 $g/cm^3$, the MOR of 503 MPa and the Young's Modulus of 237 GPa, but the post-heat treatment at $900{\circ}C$ for 8h under a flowing Ar gave rise to the cermet with the density of 2.65 $g/cm^3$, the MOR of 296 MPa, the Young's Modulus of 300 GPa. The cermet B showed better properties than the cermet A. Changes in compositions of the cermets by the post-heat treatment were observed qualitatively by XRD and SEM, the amount of Al was determined by analysis of its DSC curve.