• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.156-156
• /
• 2016

The effect of nitrogen doping on the mechanical and tribological performance of single-layer tetrahedral amorphous carbon (ta-C:N) coatings of up to $1{\mu}m$ in thickness was investigated using a custom-made filtered cathode vacuum arc (FCVA). The results obtained revealed that the hardness of the coatings decreased from $65{\pm}4.8GPa$ to $25{\pm}2.4GPa$ with increasing nitrogen gas ratio, which indicates that nitrogen doping occurs through substitution in the $sp^2$ phase. Subsequent AES analysis showed that the N/C ratio in the ta-C:N thick-film coatings ranged from 0.03 to 0.29 and increased with the nitrogen flow rate. Variation in the G-peak positions and I(D)/I(G) ratio exhibit a similar trend. It is concluded from these results that micron-thick ta-C:N films have the potential to be used in a wide range of functional coating applications in electronics. To achieve highly conductive and wear-resistant coatings in system components, the friction and wear performances of the coating were investigated. The tribological behavior of the coating was investigated by sliding an SUJ2 ball over the coating in a ball-on-disk tribo-meter. The experimental results revealed that doping using a high nitrogen gas flow rate improved the wear resistance of the coating, while a low flow rate of 0-10 sccm increased the coefficient of friction (CoF) and wear rate through the generation of hematite (${\alpha}-Fe_2O_3$) phases by tribo-chemical reaction. However, the CoF and wear rate dramatically decreased when the nitrogen flow rate was increased to 30-40 sccm, due to the nitrogen inducing phase transformation that produced a graphite-like structure in the coating. The widths of the wear track and wear scar were also observed to decrease with increasing nitrogen flow rate. Moreover, the G-peaks of the wear scar around the SUJ2 ball on the worn surface increased with increasing nitrogen doping.

• Conservation Science in Museum
• /
• v.14
• /
• pp.7-12
• /
• 2013

The conservation has been conducted for the fragments of an wooden boat in the Neolithic Age, excavated from Bibong-ri, Changnyeong, Korea. The vacuum-freeze drying have been applied to mostly to the small relics, such as wooden lacquerwares or small wooden goods etc.. Therefore, the large objects like a wooden boats have been treated almost by air-drying after impregnation with aqueous PEG solution. The air-drying is needed to impregnate with PEG aqueous solution during long period and run the risk of the fault generation. This report explain an example adapted for the fragments of the wooden boat by humidity-controlled drying(HCD) with slow adjusting moisture content. We did the chemical pre-treatment, PEG aqueous solution. The concentration of the aqueous solution was increased gradually from 10% to 80%. After the impregnation, the objects were dried by the HCD. The dimensional stability of the fragments after treatment was good.

• Tribology and Lubricants
• /
• v.38 no.3
• /
• pp.93-100
• /
• 2022

Micro-light emitting diode (micro-LED) displays offer numerous advantages such as high brightness, fast response, and low power consumption. Hence, they are spotlighted as the next-generation display. However, defective LEDs may be created due to non-uniform contact loads or LED alignment errors. Therefore, a repair process involving the replacement of defective LEDs with favorable ones is necessitated. The general repair process involves the removal of defective micro-LEDs, interconnection material transfer, as well as new micro-LED transfer and bonding. However, micro-LEDs are difficult to repair since their size decreases to a few tens of micron in width and less than 10 ㎛ in thickness. The conventional nozzle-type dispenser for fluxes and the conventional vacuum chuck for LEDs are not applicable to the micro-LED repair process. In this study, transfer conditions are determined using a micro stamp for repairing micro-LEDs. Results show that the aging time should be set to within 60 min, based on measuring the aging time of the flux. Additionally, the micro-LEDs are subjected to a compression test, and the result shows that they should be transferred under 18.4 MPa. Finally, the I-V curves of micro-LEDs processed by the laser and hot plate reflows are measured to compare the electrical properties of the micro-LEDs based on the reflow methods. It was confirmed that the micro-LEDs processed by the laser reflow show similar electrical performance with that processed by the hot plate reflow. The results can provide guidance for the repair of micro-LEDs using micro stamps.

• Korean Journal of Materials Research
• /
• v.33 no.11
• /
• pp.491-496
• /
• 2023

As the demand for p-type semiconductors increases, much effort is being put into developing new p-type materials. This demand has led to the development of novel new p-type semiconductors that go beyond existing p-type semiconductors. Copper iodide (CuI) has recently received much attention due to its wide band gap, excellent optical and electrical properties, and low temperature synthesis. However, there are limits to its use as a semiconductor material for thin film transistor devices due to the uncontrolled generation of copper vacancies and excessive hole doping. In this work, p-type CuI semiconductors were fabricated using the chemical vapor deposition (CVD) process for thin-film transistor (TFT) applications. The vacuum process has advantages over conventional solution processes, including conformal coating, large area uniformity, easy thickness control and so on. CuI thin films were fabricated at various deposition temperatures from 150 to 250 ℃ The surface roughness root mean square (RMS) value, which is related to carrier transport, decreases with increasing deposition temperature. Hall effect measurements showed that all fabricated CuI films had p-type behavior and that the Hall mobility decreased with increasing deposition temperature. The CuI TFTs showed no clear on/off because of the high concentration of carriers. By adopting a Zn capping layer, carrier concentrations decreased, leading to clear on and off behavior. Finally, stability tests of the PBS and NBS showed a threshold voltage shift within ±1 V.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.6
• /
• pp.407-410
• /
• 2018

As the operating frequency of an electromagnetic wave increases, the maximum output and wavelength of the wave decreases, so that the size of the circuit cannot be reduced. As a result, the fabrication of a circuit with high power (of the order of or greater than kW range) and terahertz wave frequency band is limited, due to the problem of circuit size, to the order of ${\mu}m$ to mm. In order to overcome these limitations, we propose a source design technique for 0.1 THz~0.3 GW level with cylindrical shape (diameter ~2.4 cm). Modeling and computational simulations were performed to optimize the design of the high-power electromagnetic sources based on Cherenkov radiation generation technology using the principle of plasma wakefield acceleration with ponderomotive force and artificial dielectrics. An effective design guideline has been proposed to facilitate the fabrication of high-power terahertz wave vacuum devices of large diameter that are less restricted in circuit size through objective verification.

• Food Science and Preservation
• /
• v.16 no.2
• /
• pp.166-171
• /
• 2009

The effects of vacuum precooling(VP) on the shelf-life of polyethylene film(PE) packaged King oyster mushrooms(Pleurotus eryngii) during storage at $-1^{\circ}C$ were investigated. VP was conducted below $0^{\circ}C$ in a $-1^{\circ}C$ cold chamber of 40 minutes, and mushrooms were stored for 30 days in batches of 1kg. The weight loss of the VP-treated mushroom was slightly lower than that of control. The $O_2$ concentrations of VP-treated mushroos, within 4 days of storage, were 2.44-14.50 %/kg-package/hr, thus higher than control values(2.01-8.19%/kg-package/hr). $CO_2$ generation of VP-treated mushrooms, again within 4 days of storage, was 0.47%/kg-package/hr, thus lower than that of controls(0.58%/kg-package/hr). The $CO_2/O_2$ ratio peaked on day 4 of storage in the control group, tbut no such peak was observed in VP-treated mushrooms. In the VP-treated fungi, lightness was higher, and redness and yellowness lower, than in controls, at all storage times.. In VP-treated mushrooms, strength, hardness and chewiness were significantly higher than in controls, but there were no significant differemces in springiness or cohesiveness. Softening and breakdown of under-cap wrinkles were observed in control mushrooms stored for 30 days, but occurred to a lesser extent in VP-treated fungi. Stipe reticulum tissue vessels in the 30 day-stored VP-treated mushrooms were relatively well-defined and clear, but were softer and diffuse in the control fungi. The results thus confirmed that VP after harvest enhanced mushroom shelf-life and PE packaging prolonged storage time. The data will have industrial applications.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.193-193
• /
• 2017

The black heart in potato is a physiological disorder that occurs when potatoes suffer from breathing problems. When storing potatoes at a low temperature around $0^{\circ}C$, there is a high possibility that the respiration rate of potato will rise and black heart will occur. Also, respiration can occur easily and briefly in a state where high temperature and ventilation is insufficient. Recently, as black heart has been occurred continuously and severely in South Korea, here we tried to identify the causes of black heart in potato and to develop the control strategy of this disorder. Firstly, we analyzed the influence on the black heart on the basis of preservation containers (breathable plastic box, burlap bag, paper box, sealed plastic box). After harvesting the potato which is cv. Superior, it preserved for 6 months under conditions of temperature $3.5^{\circ}C{\pm}0.2$ and humidity 85%, after then we surveyed the incidence of emergence rate, rate of weight loss and occurrence rate of black heart. Secondly, in order to investigate the time point of black heart initiation under the oxygen concentration condition of 1% or less, The potatoes were used for this experiment stored for 6 months in a aerated plastic box under conditions of temperature $3.5^{\circ}C{\pm}0.2$ and humidity 85% under sufficient oxygen condition. After stored for 6 month, those were stored at $15^{\circ}C$ and below 1% of oxygen for 25 days, and then the incidence of black heart was surveyed. Thirdly, to investigate the effects of the number of days after harvest on the occurrence of black heart, it was examined the occurrence of black heart stored on 40 days and 100 days after harvesting under sealed condition and vacuum condition. The temperature condition of potato storage was stored was at $4^{\circ}C$ and $25^{\circ}C$ in humidity 85%. As a result of investigating the occurrence of black heart depending on the storage containers, all of the potatoes stored in the sealed plastic box had been occurred black heart. However, black heart of the potatoes in the other treatments did not. Potato preserved under the condition of below 1% of oxygen was found to occur 32% black heart after 25 days of storage. The potatoes corresponding to the required number of days after harvesting were stored for 31 days and the black heart was examined on the occurred. As a result, the potatoes which were 40 days after the harvest did not have black heart under sealed condition and vacuum condition. But potatoes harvested 100 days after harvesting had a black heart incidence of 95.7% under sealed condition at $4^{\circ}C$. The potato placed in the vacuum condition and a sealed state at $25^{\circ}C$ was transformed into anaerobic respiration, the inner tissue of tuber collapsed. Therefore, it is considered that black heart is caused by the breathing trouble in the central part when the oxygen is almost consumed after the aerobic respiration which gradually consumes the oxygen. We conclude that the black heart occurred in the central part where exchange of oxygen and carbon dioxide is the slowest is sensitive to respiration disorder. It is thought that research to investigate black heart generation time according to storage conditions and post-harvest state of potatoes is further necessary.

• Journal of Mechanical Science and Technology
• /
• v.18 no.9
• /
• pp.1680-1688
• /
• 2004

The information indicating device plays an important part in the information times. Recently, the classical CRT (Cathod Ray Tube) display is getting transferred to the LCD (Liquid Crystal Display) one which is a kind of the FPDs (Flat Panel Displays). The OLED (Organic Light Emitting Diodes) display of the FPDs has many advantages for the low power consumption, the luminescence in itself, the light weight, the thin thickness, the wide view angle, the fast response and so on as compared with the LCD one. The OLED has lately attracted considerable attention as the next generation device for the information indicators. And also it has already been applied for the outside panel of a mobile phone, and its demand will be gradually increased in the various fields. It is manufactured by the vapor deposition method in the vacuum state, and the uniformity of thin film on the substrate depends on the temperature distribution in the point-cell source. This paper describes the basic concepts that are obtained to design the point-cell source using the computational temperature analysis. The grids are generated using the module of AUTOHEXA in the ICEM CFD program and the temperature distributions are numerically obtained using the STAR-CD program. The temperature profiles are calculated for four cases, i.e., the charge rate for the source in the crucible, the ratio of diameter to height of the crucible, the ratio of interval to height of the heating bands, and the geometry modification for the basic crucible. As a result, the blowout phenomenon can be shown when the charge rate for the source increases. The temperature variation in the radial direction is decreased as the ratio of diameter to height is decreased and it is suggested that the thin film thickness can be uniformed. In case of using one heating band, the blowout can be shown as the higher temperature distribution in the center part of the source, and the clogging can appear in the top end of the crucible in the lower temperature. The phenomena of both the blowout and the clogging in the modified crucible with the nozzle-diffuser can be prevented because the temperature in the upper part of the crucible is higher than that of other parts and the temperature variation in the radial direction becomes small.

• Journal of the Korean Society of Radiology
• /
• v.3 no.4
• /
• pp.29-33
• /
• 2009

Recently, the compound materials(a-Se, $HgI_2$, PbO, CdTe, $PbI_2$, etc.) that are used in flat panel x-ray imager have been studied for digital x-ray imaging. In this paper, the signal detection properties of $HgI_2$ and a-Se conversion layer, are compared. The thick $HgI_2$ film is fabricated by special particle-in-binder method and the conventional vacuum thermal evaporation is used for a deposition of a-Se film. And an electrical characteristic measurements were investigated about leakage current, signal response property and x-ray sensitivity. From the experimental results show that the $HgI_2$ film has a low operation voltage and high signal generation than that of a-Se.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.420-424
• /
• 2016

In this study, we developed photocatalytic technology to address the emerging serious problem of air pollution through indoor air cleaning. A single layer of $WO_3$ was prepared by using the dry process of general RF magnetron sputtering. At a base vacuum of $1.8{\times}10^{-6}$[Torr], the optical and electrical properties of the resulting thin films were examined for use as a transparent electrode as well as a photocatalyst. The single layer of $WO_3$ prepared at an RF power of 100 [W], a pressure of 7 [mTorr] and Ar and $O_2$ gas flow rates of 70 and 2 sccm, respectively, showed uniform and good optical transmittance of over 80% in the visible wavelength range from 380 [nm] to 780 [nm]. The optical catalyst characteristics of the $WO_3$ thin film were examined by investigating the optical absorbance and concentration variance in methylene blue, where the $WO_3$ thin film was immersed in the methylene blue. The catalytic characteristics improved with time. The concentration of methylene blue decreased to 80% after 5 hours, which confirms that the $WO_3$ thin film shows the characteristics of an optical catalyst. Using the reflector of a CCFL (cold cathode fluorescent lamp) and the lens of an LED (lighting emitting diode), it is possible to enhance the air cleaning effect of next-generation light sources.