• 한국전기전자재료학회논문지
• /
• 제11권8호
• /
• pp.581-586
• /
• 1998

This paper describes athermally stimulated displacement current (TSDC) of arachidic acid(AA) and polyamic acid alkylamine salts(PAAS) Langmuir-Blodgett(LB) films, which is a precursor of polyimide(PI). The TSDC measurements of AA LB film were performed from temperature to about 11$0^{\circ}C$ at a rate of 0.2$^{\circ}C$/ｓ inside a vacuum chamber for a reference. And the TSDC measurements PAAS LB film were performed from room temperature to about 25$0^{\circ}C$ and temperature was increased at the same rate as that of AA LB film. They show that there are TSDC peaks at about 7$0^{\circ}C$ in the arachidic acid LB films, and at about 7$0^{\circ}C$ and 16$0^{\circ}C$ in the PAAs LB films. Results of these measurements indicate the one small peak at 7$0^{\circ}C$ is resulted from a softening of the alkyl group and the large peak at 16$0^{\circ}C$ is possibly due to dipole of C-O group in the PASS molecule. We have calculated the vertical component of the AA and PAAs L film out of the TSDC curves. It shows that the dipole moment of the AA LB film is about 70-mD at 7$0^{\circ}C$. And the dipole moment of PAAS LB film is about 040mD at 7$0^{\circ}C$ and about 200mD at 16$0^{\circ}C$ in the first measurement of TSDC. In the second measurement of TSDC of PASS LB film after cooling down to room temperature, the TSDC peaks are almost disappeared.

• 대한화학회지
• /
• 제36권6호
• /
• pp.832-839
• /
• 1992

Time-of-Flight(TOF) 질량분석기가 설치된 분광분석장치를 이용하여 레이저 공명이온화 분광법으로 극미량의 납을 정량하였다. 납에 대한 극미량 분석을 위해 단색 2광자 공명이온화, 2색 2광자 공명이온화 및 3색 3광자 공명 이온화의 세 가지 광이온화 경로가 시도되었다. 이 때, 첫번째 들뜬 준위는 바닥준위로부터 283.3 nm의 파장에 해당하는 6p7s($^3P_1$)준위를 공통적으로 사용하였다. 이들 이온화경로를 통해 여러가지 농도의 납 표준용액을 사용하여 0.1 ${\mu}g$에서 1pg의 영역에 해당하는 검정곡선을 얻었다. 검정곡선으로부터 얻은 본 분석법의 검출한계는 2색 2광자 공명이온화 및 3색 3광자 공명이온화의 경우 각각 20 및 10pg 이었다. 또한 각각의 이온화 경로에 따른 이온화 효율도 함께 비교 검토하였다.

• Journal of Magnetics
• /
• 제15권4호
• /
• pp.179-184
• /
• 2010

We have investigated the effects of post annealing on iron oxide nanoparticles synthesized by the novel hydrothermal synthesis method with the $FeSO_4{\cdot}7H_2O$. To investigate the post annealing effect, the as-synthesized iron oxide nanoparticles were annealed at different temperatures in a vacuum chamber. The morphological, structural and magnetic properties of the iron oxide nanoparticles were investigated with high resolution X-ray powder diffraction (XRD), high resolution transmission electron microscopy (HRTEM), Mossbauer spectroscopy, and vibrating sample magnetometer analysis. According to the XRD and HRTEM analysis results, as-synthesized iron oxide nanoparticles were only magnetite ($Fe_3O_4$) phase with face-centered cubic structure but post annealed iron oxide nanoparticles at $700^{\circ}C$ were mainly magnetite phase with trivial maghemite ($\gamma-Fe_2O_3$) phase which was induced in the post annealing treatment. The crystallinity of the iron oxide nanoparticles is enhanced by the post annealing treatment. The particle size of the as-synthesized iron oxide nanoparticles was about 5 nm and the particle shape was almost spherical. But the particle size of the post annealed iron oxide nanoparticles at $700^{\circ}C$ was around 25 nm and the particle shape was spherical and irregular. The as-synthesized iron oxide nanoparticles showed superparamagnetic behavior, but post annealed iron oxide nanoparticles at $700^{\circ}C$ did not show superparamagnetic behavior due to the increase of particle size by post annealing treatment. The saturation of magnetization of the as-synthesized nanoparticles, post annealed nanoparticles at $500^{\circ}C$, and post annealed nanoparticles at $700^{\circ}C$ was found to be 3.7 emu/g, 6.1 emu/g, and 7.5 emu/g, respectively. The much smaller saturation magnetization value than one of bulk magnetite can be attributed to spin disorder and/or spin canting, spin pinning at the nanoparticle surface.

• 반도체디스플레이기술학회지
• /
• 제15권1호
• /
• pp.65-69
• /
• 2016

We have investigated the possibility of recycling of an organic material that is wasted during thermal evaporation. To this end, we have collected a wasted organic material (N,N'-diphenly-N,N'-bis(1,1'-biphenyl)-4,4'-diamine(NPB)) from a vacuum chamber, purified it by recrystallization, and fabricated bilayer organic light-emitting diodes (OLEDs) with the recycled NPB. It is found that the surface roughness of thin films coated with the purified NPB is much enhanced. OLEDs fabricated by thermal evaporation of the purified NPB show lower device efficiency than OLEDs with the original NPB. However, the power efficiency of OLED fabricated by spin coating of the purified NPB is comparable with that of OLED with the original NPB. Therefore, such a recycling method by recrystallization would be more suitable for solution-processed OLEDs.

• 한국정보통신학회논문지
• /
• 제18권9호
• /
• pp.2251-2258
• /
• 2014

본 논문에서는 이동식 복지용구 소독을 위한 통합제어시스템을 개발하였다. 통합제어시스템은 과산화수소 증기 공급 제어회로와 저 진공을 이용한 살균 소독챔버 제어회로 및 마이크로버블을 이용한 세탁 제어회로 구성된다. 개발한 통합제어시스템에 대한 동작상태 및 통신 상태 등을 측정하기 위하여 스마트 기반의 원격 제어 및 모니터링 시스템을 구현하였다. 개발한 통합제어시스템 에 대한 성능을 평가하기 위해 실험 장치를 구현하였다. 제어회로에 대한 동작상태 및 신호 송수신 등을 측정해본 결과, 정상적으로 동작함을 알 수 있었다. 그리고 스마트 기반의 원격 제어 및 모니터링 시스템과의 연동 테스트에서 개발한 통합제어시스템이 통신상태, 센서 인터페이스 및 제어 면에서 좋은 동작성능을 보였다. 향 후 개발한 제어시스템을 실 시스템에 적용하여 그 성능을 증명하는 것이 필요하다.

• 한국표면공학회지
• /
• 제29권5호
• /
• pp.345-349
• /
• 1996

The wetting property of polymer surfaces is very important for practical applications. Plasma source ion implantation technique was used to improve the wetting properties of polymer surfaces. Poly(ethylene terephtalate) and other polymer sheets were mounted on the target stage and an RF plasma was generated by means of an antenna located inside the vacuum chamber. High voltage pulses of up to -10kV, 10 $\mu$sec, and up to 1 kHz were applied to the stage. The samples were implanted for 5 minutes with using Ar, $N_2,O_2,CH_4,CF_4$ and their mixture as source gases. A contact angle meter was used to measure the water contact angles of the implanted samples and of the samples stored in ambient conditions after implantation. The modified surfaces were analysed with Time-Of-Flight Mass Spectrometer (TOF-SIMS) and Auger Electron Spectroscopy (AES). The oxygen-implanted samples showed extremely low water contact angles of $3^{\circ}C$ compared to $79^{\circ}C$ of unimplanted ones. Furthermore, the modified surfaces were relatively stable with respect to aging in ambient conditions, which is one of the major concerns of the other surface treatment techniques. From TOF-SIMS analysis it was found that oxygen-containing functional groups had been formed on the implanted surfaces. On the other hand, the $CF_4$-implanted samples turned out to be more hydro-phobic than unimplanted ones, giving water contact angles exceeding $100^{\circ}C$ . The experiment showed that plasma source ion implantation is a very promising technique for polymer surface modification especially for large area treatment.

• 분석과학
• /
• 제7권4호
• /
• pp.471-476
• /
• 1994

PIXE(양성자 유발 X-선 발생) 분석법을 이용한 박막 두께 측정의 가능성을 알아보기 위하여, 구리판 위에 코팅된 금 박막 시료들을 이용하여 실험을 수행하였다. 두 가지 실험방법을 사용하여 분석을 하였으며, 결과를 비교하여 보았다. 또한 분석 결과의 정확성을 확인하기 위하여 무게측정 방법과 양성자 RBS 분석법에 의한 결과들과 비교하여 보았다. 이 분석 방법은 고고학 시료나 거대시료와 같이 진공 표적함에 집어 넣을 수 없는 경우에도 비파괴적으로 박막의 두께를 측정할 수 있는 장점을 갖고 있다.

• 한국항공운항학회지
• /
• 제17권4호
• /
• pp.8-16
• /
• 2009

An experimental study was carried out to investigate aerodynamic characteristics on reduced frequency of flapping wings. The half span of the wing is 28cm, and the mean chord length of wing is 10cm. In flight, the Reynolds Number range of birds is about $10^4$, and the reduced frequency during a level flight is 0.25. The experimental variables of present study were set to have similar conditions with the bird flight's one. The freestream velocities in a wind tunnel were 2.50, 3.75 and $5.00^m/s$, and the corresponding Reynolds numbers were $1.7{\times}10^4$, $2.5{\times}10^4$ and $3.3{\times}10^4$, respectively. The wing beat frequencies of an experimental model were 2, 3 and 4Hz, and the corresponding reduced frequency was decided between 0.1 and 0.5. Aerodynamic forces of an experimental flapping model were measured by using 2 axis load-cell. Inertial forces measured in a vacuum chamber were removed from measuring forces in the wind tunnel in order to acquire pure aerodynamic forces. Hall sensors and laser trigger were used to make sure the exact position of wings during the flapping motion. Results show that the ratio of downstroke in a wing beat cycle is increased as a wing beat frequency increases. The instantaneous lift coefficient is the maximum value at the end of downstroke of flapping wing model. It is found that a critical reduced frequency with large lift coefficient is existed near k=0.25.

• 한국산학기술학회논문지
• /
• 제12권4호
• /
• pp.1803-1811
• /
• 2011

TFT-LCD용 TFT기판 상에서 저에너지 마이크로 컬럼을 이용하는 전기적인 결함 검출 메카니즘을 분석하였다. 본 연구에서는 고진공 챔버 내에서 7인치 TFT 기판에 저에너지 전자빔을 주사하여 여러 가지 불량 화소에 대한 SEM 이미지를 획득하였다. 더불어 각각의 불량 화소에서 나타나는 현상과 전기적인 거동과의 연관성을 분석하여 검출 메카니즘을 해석하였다. 그 결과로서 저에너지 초소형 전자 컬럼을 이용하는 저에너지 전자빔에 의한 SEM 이미지는 전자간 반발효과에 크게 영향을 받는 일관성 있는 결과를 확인하였다.

• 자원리싸이클링
• /
• 제9권3호
• /
• pp.13-21
• /
• 2000

본 연구는 폐용제를 가열, 증발 및 음축과정을 거쳐 용제를 회수하는 시스템의 열교환기 해석에 관한 것으로, 고온 열매체유로 가열되는 이중관형 열교환기를 사용하여 용제 증발과정의 열전달 특성을 분석하고 용제유량과 가열온도에 따라 물, 벤젠 및 알칼벤젠의 증발을 위해 요구되는 전열면적을 분석하였다. 폐용제 회수장치는 용제 공급펌프 이중관형 열교환기, 진공 스프레이 챕버 및 응축기동으로 구성되며, 이중관형 열교환기는 용제액을 열적 포화온도를 가열시키는 구간과 포화된 용제액을 증발시키는 구간으로 구성된다. 관 내 용제의 증발을 위한 전열면적을 열평형 모델링에 의해 예측하였고, 이중관형 열교화기의 관 내 온도분포 측정을 통해 이론값과 비교 분석하였다. 용제유량 0.1~0.51l/mm 및 가열온도 130~$260^{\circ}C$의 범위에서 용제유향 증가 및 가열온도 감속에 따라 단위전열면적당 열전달양이 감소하기 때문에 용제 증발을 위한 전열면적은 증가하였다. 관 내 용제 증발을 위한 전열면적의 이론적 분석결과는 측정값과 일치하였으며, 이중관형 열교환기를 사용한 폐용제의 증발과정을 통해 용제를 회수하는 기술에 적용이 가능하다.