• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.19-25
• /
• 2014

The purpose of this study is to establish experimentally the mechanical properties of fiber reinforced concrete using kenaf dosages and propose the usable method of kenaf fiber in the concrete industry as natural fiber materials. Kenaf fiber help make the concrete strength including tensile and flexural stronger, more resistant to plastic and drying shrinkage, less amount of carbon dioxide because of having a rough surface and excellent tensile strength of fiber and improving the concrete's corrosion resistance. It is to select the kenaf dosages of 4 cases (0, 0.3, 0.6 and $0.9kg/m^3$ and perform various tests including slump, air content, plastic and drying shrinkage, flexural and tensile strength for fiber reinforced concrete. The results of this study are as follows : In case of increasing kenaf fiber dosages, show the slump decrease and air content increase, also take effect results for increasing concrete strength including flexural and tensile, decreasing plastic and drying shrinkage. therefore, considered test results and cost, the optimum dosages of kenaf fiber is proposed about $0.6kg/m^3$ and need to study on the site application considering concrete quality and another compared tests.

• Journal of the Korean Geosynthetics Society
• /
• v.9 no.1
• /
• pp.39-46
• /
• 2010

Recently, the effective use of closed waste landfill nearby urban areas has been demanded, because of the lack of the usable land. However, the reuse of closed landfill is needed an adequate stabilization of liner system. But most of these places are consisted of steep slope and hence it is necessary to use the geosynthetics liners in there. Liner system of waste landfills is an important facility which prevents leachate outgoing from the landfills and also groundwater infiltrating from surroundings into the landfills. During the waste disposal stage, differential settlement and tensile stress of the geosynthetic materials could occur due to impact load of trucks and dozers, waste loads and weak foundation soils. In this study, the tensile strength and tracer test were performed to evaluate the stability of geomembrane liner systems. Based on the tensile strength test result of in-situ geomembrane sample, the yield tensile strength maintain the suitable strength by specification and current law. However, according to the tracer test, the damage of geomembrane liner was detected on sanitary landfill section.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.2
• /
• pp.89-95
• /
• 2001

The 7175Al alloy is particularly interesting for its high strength and sufficient ductility, fracture toughness and corrosion resistance. Currently vigorous efforts have been made to develop large rockets usable for various purposes in the space. This has created the demand of big size of 7175Al billet which would be applied to heavy forgings. The aim of this study is to investigate the quality level of big billet and the effect of billet size on the mechanical properties of large 7175Al ring roll forgings. The billets range from 370 mm to 720 mm in diameter were homogenized and forged after direct chill casting. The size and volume fraction of second phase particles In ${\Phi}720$ mm billet are larger than those of ${\Phi}370$ mm billet, and its ductility is lower for the condition of homogenization and T6 treatment. The Cu-rich phases formed in interdendritic sites are considered to provide the preferential crack path during cold upsetting. The fracture toughness of ring roll forgings which are made by ${\Phi}370$ mm billet is higher than those of ${\Phi}720$ mm billet.

• Applied Chemistry for Engineering
• /
• v.2 no.3
• /
• pp.289-299
• /
• 1991

In order to obtain glasses appropriate to the thick film copper conductors, nine glasses based on both lead borosilicate and leadless borosilicate systems were made and the applicabilities of them were examined in conjunction with the requirements for thick film copper conductors. As the results, it was found that all the glasses are fitted to provide suitable sheet resistance, solderability and solder leach resistance to thick film copper conductors. However, it was turned out that only the lead borosilicate based glasses worked for getting usable aged adhesion strength of copper thick film to the alumina substrate, while copper conductor films made from the other glasses had poor aged adhesion strengths. Particularly cuprous oxide added lead borosilicate glass was considered as one of the most favorable glasses for manufacturing thick film copper conductors.

• 보존과학연구
• /
• s.21
• /
• pp.101-118
• /
• 2000

Stone cultural properties(pagoda, Buddhist statue etc.) is moved in original place for many reasons and restored after taking to pieces for structural safety. With the movement and restoration after taking to pieces, the cast iron is used for the sake of a fixation and horizontality. The stone cultural properties are spoiled the beauty and accelerated the weathering because of the corrosion product of cast iron. So we need to substitute for the improved property in all aspects. We are executed the corrosion test and inquired the property of material on the usable material for the shim of stone cultural properties. That is the Cast iron, Stainless steel, Titanium and Fiber Reinforced Plastics. In the result of the physical property and strength, the Stainless steel and Titanium was superior to the Cast iron. And the Stainless steel and Titanium was slower than the Cast iron in the corrosion velocity for the acid, salt and rain. If the shim is substitute the Stainless steel or Titanium for the Cast iron, the stone cultural properties are able to reduce the pollution of stone cultural properties by corrosion product and should not happen in the matter of stone pagoda.

• Journal of Environmental Science International
• /
• v.25 no.11
• /
• pp.1521-1530
• /
• 2016

As a result of dividing typhoon that affected Korean Peninsular between 1999 and 2012 into 7 types of path and entering forecast field and analysis field of RDAPS, until 36 hours from the time of forecast, it is reliable to use the forecast field of RDAPS to predict typhoon and for each typhoon path, the difference between the forecast and the analysis shows normal distribution, which is usable for weather forecast until the $36^{th}$ hour. In the $48^{th}$ hour from the time of forecast, the difference of result depending on each typhoon path increased, which was analyzed to be due to errors in the forecast. It was expected that relatively reasonable results should be shown if the $36^{th}$ hour forecast is used to predict the strength and distribution of strong wind. As a result of using Korean RAM and observing the difference of the maximum damage, reliability was secured up to 36 hours and after 48hours, it was expected that the fluctuation of results may become more severe.

• Biomaterials and Biomechanics in Bioengineering
• /
• v.5 no.1
• /
• pp.65-86
• /
• 2020

As conventional drug delivery system is being improved rapidly by target-based drug delivery system, finding suitable Drug Delivery System (DDS) for new drugs remains a challenge. Although there are many drug delivery vehicles in existence, a significant improvement is required to some DDS such as for local, implant-based treatments used for musculoskeletal infections. Many polymers have been considered for providing the improvement in DDS. Synthetic polymer, for example, has gained popularity for broad-spectrum physicochemical and mechanical properties. This article reviews the biomedical applications of Poly(TriMethylene Carbonate-co-Caprolactone) (PTMCC), which has attracted attention due to its biocompatibility, biodegradability and rubber-like properties. Its synthesis, physical properties, and degradation are also discussed here. Although it is relatively new in biomedical applications, it is readily usable for the fabrication of differing format of DDS of superior mechanical strength and degradation properties. The use of PTMCC is expected to increase in coming years as more is revealed about its potentials.

• Journal of Fashion Business
• /
• v.15 no.3
• /
• pp.32-50
• /
• 2011

This study is designed to analyze the effects of demographic factors on children's wear brand preference and their reasons, and brand evaluations. A total of 355 usable data was collected from housewives in three metropolitan cities (Seoul, Daejeon, and Sungnam) in Korea. An ANOVA and crossing analysis were used to determine the strength(percentage) among several dependent variables. Also, regression analysis was used to examine the effects of demographic factors on each factor and component related to fashion brand evaluation. Overall, ANOVA and crossing analysis results showed that the visual attributions (variables) of clothing marked significantly higher scores than others (functional attributions). This result is noteworthy because it is opposite of common stereotypes and prejudices that selectors who first recognize visual information (aesthetic attributions) as a clothing buying criteria should be unsatisfied with them after wearing. Therefore, this research suggests that the chief reason in determining the outcome of success or failure in fashion industry depends on their trend productions with fashion image creation by reflecting the exclusive trends based on consumer's taste and wants.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.2
• /
• pp.455-460
• /
• 2020

As computer hardware and computer graphics technologies have developed in recent years, one can find research on the creation of bubbles. However, it is not easy to find soap bubbles that are modeled and rendered using actual physical parameters. The bubbles are expressed in a variety of models and colors depending on which tool is used, which strength is used, and the conditions of the surrounding environment. Therefore, in this paper, we present synthetic methods to create virtual soap bubbles based on physical parameters derived from some straws such as the bubbles' diameter over time and the number of bubbles when blowing. On the top of that, we will show a model of a soap bubble that can be usable in a virtual reality contents and optimized with rendering parameters.

• Journal of Industrial Technology
• /
• v.43 no.1
• /
• pp.7-13
• /
• 2023

Nowadays, traffic congestion is emerging as a major problem due to the rapid population growth and the increase in automobiles. The train is a convenient means of transportation that can efficiently solve these problems. Trains have been developed in line with human aspirations for a long time, but research on safety is still insufficient. This study aims to check safety by conducting static tests and fatigue tests on bogie frames, and to help develop bogie frames in the future. For the static test, a strain gauge was attached to the point where the local stress concentration was expected beforehand, and the result value was derived, compared with existing theories, and expressed as a Goodman diagram. In the fatigue test, a total of 10 million loads were applied over three stages, and no cracks appeared in the non-destructive test conducted after each stage. Both tests were conducted according to the strict test method of the bogie frame presented by the UIC Code. It satisfied both fatigue life and strength evaluation criteria and was judged to be a bogie frame usable for safe train production.