• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.44-48
• /
• 2001

In this paper we describe the design of symbol timing and carrier synchronization algorithms for burst receiver. The demodulator consists of digital down converter, matched filter and synchronization circuits. For symbol timing recovery we use modified Gardner algorithm. And we use decision directed method for carrier phase recovery. For the sake of performance analysis, we compare simulation results with the board implemented by FPGA which is APEX20KE series chip for Alter. The performance results show it works quite well up to the condition that a frequency offset equal to 0.1% of symbol rate.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.11a
• /
• pp.363-363
• /
• 2004

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.318-320
• /
• 2007

Single-phase cycloconverters are widely used for ac-ac power conversion especially for speed control of ac drives. In this paper, a new single-phase to single-phase Z-source cycloconverter topology is proposed. The proposed single-phase Z-source cycloconverter can boost to a desired voltage with various frequency. Thus, it is called a frequency step-down and amplitude voltage step-up converter. The operating principle of the proposed topology is presented. Analysis and simulation for this single-phase Z-source cycloconverter are also presented.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.23-24
• /
• 2015

본 논문에서는 하나의 입력으로 강압과 승압된 두 개의 출력을 가지는 승 강압 겸용 DC-to-DC 컨버터를 제안한다. 승압 출력이 가능한 컨버터는 기존의 부스트 컨버터와 동일한 구조이고, 강압 출력이 가능한 컨버터는 배터리의 직 병렬 가변 결합을 이용한다. 강압출력이 가능한 컨버터 동작에서 배터리는 강압 출력의 입력원이 되어 기존의 벅컨버터보다 2배 이상 강압 가능한 장점이 있다. 본 논문은 제안하는 승 강압 겸용 DC-to-DC 컨버터의 구조 및 동작 모드에 따른 이론적 분석을 시행하고 컴퓨터 시뮬레이션을 통해 타당성을 검증한다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.6
• /
• pp.951-958
• /
• 2008

This paper describes development of hardware simulator for the PMSG wind power system, which was designed considering wind characteristic, blade characteristic and blade inertia compensation. The simulator consists of three major parts, such as wind turbine model using induction motor, PMSG generator, converter-inverter set. and control system. The turbine simulator generates torque and speed signals for a specific wind turbine with respect to given wind speed. This torque and speed signals are scaled down to fit the input of 2kW PMSG. The PMSG-side converter operates to track the maximum power point, and the grid-side inverter controls the active and reactive power supplied to the grid. The operational feasibility was verified by computer simulations with PSCAD/EMTDC, and the implementation feasibility was confirmed through experimental works with a hardware set-up.

• Journal of Power Electronics
• /
• v.12 no.1
• /
• pp.98-103
• /
• 2012

This paper presents a digital pulse width modulator (DPWM) with a reduced digital modulation delay (a transport delay of the modulator) during the transient response of power converters. During the transient response operation of a power converter, as a result of dynamic variations such as load step-up or step-down, the closed loop controller will continuously adjust the duty cycle in order to regulate the output voltage. The larger the modulation delays, the larger the undesired output voltage deviation from the reference point. The three conventional DPWM techniques exhibit significant leading-edge and/or trailing-edge modulation delays. The DPWM technique proposed in this paper, which results in modulation delay reductions, is discussed, experimentally tested and compared with conventional modulation techniques.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1114_1115
• /
• 2009

The wind most of the century, the average wind speed in the coast area 6m/s~8m/s operation as a large wind power generators is not enough to produce. But the generator of proposed wind turbine system is connected to Hydraulic torque converter is the actual development of this usage, the low investment and economic effects appear to be much lower there is. In case of the proposed wind turbine system, is possible to make torque transmission long distance, set up generator somewhere in between the tower or the ground as well as, nacelle weight can be greatly down.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1032-1034
• /
• 2001

As well known, a solar cell has an optimal operating point to be able to get the maximum power $P_{max}$. So, many $P_{max}$ tracking controllers using the line voltage of a solar cell have been popularly used. But it may vary depending on the miss match between the solar cell output and the load. In this paper, we investigate the possibilities of $P_{max}$ control using the current tracking controller and the output voltage and the output current instead of the solar cell output power. And we also examine about the optimal power converter using ZVCS step up and down chopper circuit to operate the solar cell at an optimal voltage using these variables. And then, we show some experimental results to confirm the successful operation.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.182-183
• /
• 2013

In the design of the fuel cell charger, it is important to find out the suitable topology and to design the converter to guarantee the performance of the fuel cell as well as the battery. Most of the chargers developed so far have used step-down converters. However, since the small fuel cell stack can only generate a low voltage, it is required to use the step-up converter to charge the battery. In this paper, a modified non-isolated boost charger topology for the Proton Exchange Membrane Fuel Cell (PEMFC) is proposed to meet the strict ripple requirements for the battery charge and its control method by using PI controller is detailed. The feasibility of the proposed topology and its control method is then verified by the experiments.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.5
• /
• pp.413-421
• /
• 2013

This paper proposes residential hybrid distribution system that can supply AC power and DC power to AC load and DC load at the same time. This hybrid distribution system consists of three parts: bidirectional inverter, step-up converter and step-down converter. Also that is used to supply voltage to home application is classified of AC load and DC load as load characteristics. The performance of proposed hybrid distribution system is validated through the hardware implementation and the experimental results.