• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.4
• /
• pp.518-524
• /
• 1997

Experimental studies on combustion phenomena within a porous ceramic burner are reported. Main interest of the present work is to investigate fundamental flame behaviors and their effects on the burner operation. Due to high thermal capacity of the porous ceramic materials, the response of flame to burning condition changes is slow and thus to have a stabilized flame is quite difficult and takes much time. It is found that the temperature profile obtained at downstream of the flame zone is not much sensitive to the movement of flame and the speed of flame movement is less than 0.1 mm/sec for the conditions tested. With the premixed LPG/air flame imbedded within the porous ceramic burner, stable combustion regions and unstable combustion regions leading to blowoff or flashback phenomena are observed and mapped on flow velocity versus equivalence ratio diagram. For the development of burner operation technique which is more practical and safe, intermittent burning technique, where the fuel or/and air is supplied to the burner intermittently, is proposed as one of the flame control methods for the porous ceramic burner and tested in this study. Through the experiment, it is realized that the proposed method is acceptable in respect to burner performance and give much flexibility in the operation of porous ceramic burner.

• Steel and Composite Structures
• /
• v.26 no.1
• /
• pp.31-44
• /
• 2018

This paper reports a novel steel beam-to-column connection suitable for use in the weak axis of I-section column. Monotonic and cyclic loading experimental investigations and numerical analysis of the proposed weak-axis connection were conducted, and the calculation procedure of the beam-column relative rotation angle and plastic rotation angle was developed and described in details. A comparative analysis of mechanical property and steel consumption were employed for the proposed I-section column weak-axis connection and box-section column bending connection. The result showed that no signs of fracturing were observed and the plastic hinge formed reliably in the beam section away from the skin plate under the beam end monotonic loading, and the plastic hinge formed much closer to the skin plate under the beam end cyclic loading. The fracture of welds between diaphragm and skin plate would cause an unstable hysteretic response under the column top horizontal cyclic loading. The proposed weak-axis connection system could not only simplify the design calculation progress when I-section column is adopted in frame structural design but also effectively satisfy the requirements of 'strong joint and weak member', as well as lower steel consumption.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.2 s.32
• /
• pp.74-82
• /
• 1999

Nowadays, the crank shaft motor vehicle has become essential as the important component. The machining precision was asked for manufacturing the shaft. They could be unstable in the quality by the conventional are welding. Both in-process quailty control and high reliability of the weld are the major concerns in applying friction wlding to the economical and qualified mass-production. No reliable nondestructive monitoring method is avaliable at present to determine the real-time evaluation of automatic production quality control for bar-to-bar friction welding of the crank shaft of O.D 24mm for motor vehicle. This paper, so that, presents the experimental examinations and statistical quantitative analysis of the correlation between the cumulative counts of acoustic emission(AE) during plastic deformation periods of the welding and the tensile strength and other properties of the bar-to-bar welded joints of O.D. 24mm shaft as well as the various welding variables, as a new approach which attempts finally to develop real-time quality monitoring system for friction welding, resulting in practical possiblility of real-time quality control more than 100% joint efficiency showing good weld with no micro structural defects.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.814-819
• /
• 2017

The objective of this paper is to observe effects of an ignition position and time on the ignition transition. A gaseous oxygen and liquid kerosene are used for propellants with the shear-coaxial injector. In order to study the ignition delay time and combustion instability intensity, the pressure transducer was used. The ignition position was changed with the injector spacer. Sequences except the igniter operation time were fixed to compare the ignition time only. Initial pressure peak and ignition delay time increased as the ignition time was delayed. Also, the unstable flame development zone was detected as the igniter was away from the injector.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.1 s.62
• /
• pp.44-48
• /
• 2005

The shock absorbers for marine vehicles are very important components to absorbing the shock resulting from driving. Depending on the kinds of vehicles, these essential components, piston and piston rod, must be made of S25C, S45C, and SCM440, must be precisely machined, and assembled by the bolts. Other materials used have been difficult to weld, and could be unstable in quality, by the conventional arc welding. Also, they have been associated with a lot of technical problems in manufacturing. However, using the friction welding technique, such problems will be avoided. These factors have necessitated the domestic development of the marine shock absorber using a friction welding, as well as stimulating a new approach to the study of real-time weld quality evaluation by AE techniques.

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.1
• /
• pp.63-72
• /
• 2005

From the geological and engineering point of view, the limestone is so rigid that it is able to act as a bedrock but if there are some unstable elements which are solubility cavity and cracking zone in the ground, the settlement and bearing capacity of a structure will be required to long-term stability investigations and countermeasures about those problems. When comparing the allowable bearing capacity, the results of Bell's method and the Bowles' method are similar but the results of Hoek-Brown's method are very larger than the others. For weathered limestone, stability is changed by size and depth of the cavity of limestone, but soft and hard rock are stable regardless of size and depth of the cavity.

• The Journal of Engineering Geology
• /
• v.30 no.3
• /
• pp.289-302
• /
• 2020

To determine the shallow subsurface structure and sliding surface of land creeping in 2016 at Hadong-gun, Gyeongsangnam-do, geophysical surveys (electric resistivity, and refraction seismic methods, borehole televiewer) and slope stability analysis were conducted. The subsurface structure delineated with borehole lithologies and seismic velocity structures provided the information that the sediment layer on the top of the slope was rather as thick as 20 m and the underlying weathered rock (anorthosite) was thinner than 1 m. Based on the tension cracks observed during the geological mapping, televiewer scanning was performed at the borehole BH-2 and detected the intensive fracture zones at the ground-water level, associated with the slip weak zones mapped in dipole-dipole electrical resistivity section. Downslope sliding and slightly upward pushing at the apex of high resistive bedrock explains the curved slip plane of the land creeping. Such a convex structure might play a role of natural toe abutment for preventing the downward development of slip weak zones. In slope stability analysis, the safety factors of the slip weak zone are calculated with varying the groundwater levels for dry and rainy seasons and the downslope is founded to be unstable with safety factor of 0.89 due to fully saturated material in rainy season.

• Explosives and Blasting
• /
• v.23 no.4
• /
• pp.31-44
• /
• 2005

In highly stressed conditions, the excavation damage zone induced by stress redistribution and disturbance must be evaluated after tunnel excavation. Therefore, the investigation of stress-induced deformation and fracture in rock is indispensable. In this study, fracture and damage mechanisms of rock induced by the accumulation of microcracks were investigated by the moving point regression technique as well as acoustic emission measured during uniaxial compression tests. Especially, the modified procedures to determine damage thresholds more systematically were newly proposed, and successfully applied to rock. From experiments, crack initiation and track damage stress levels were estimated to be $33{\~}36\%$ and $84{\~}89\%$ of uniaxial compressive strength respectively, for both of Hwangdeung granite and Yeosan marble. However, the normalized crack closure stress level for Yeosan marble was much higher than for Hwangdeung granite. In addition, the largest proportion of total axial strain in Hwangdeung granite was attributable to elastic deformation and initial microcracking. However, the greatest part of axial deformation in Yeosan marble arose from initial crack closure and unstable cracking. Finally, it was seen that unstable cracking after the crack damage stress level played a key part in the lateral deformation in rocks under uniaxial compression.

• Journal of the Korean Arthroscopy Society
• /
• v.6 no.2
• /
• pp.142-149
• /
• 2002

Purpose : The purpose of this study is to compare with result of repair and resection in displaced bucket handle medial meniscal tear. Materials and Methods : From Sep. 1998 to Dec. 2001, we experienced 46 cases, 45 patients. We classified them into repair group (group I, 23 cases) and resection group (group II, 23 cases). We analyzed the time interval between injury and operation, zone of tear, the status of reduction and quality of displaced fragment of all cases. Average follow-up period is 29, 28 months, respectively. We evaluated the final results of both groups as Lysholm knee score, radiologic changes and 2nd look arthroscopy. Results : Mean age was 25 years old in both group, respectively. Mean interval between injury and surgical treatment was 12 and 17 weeks. respectively. In group I, 6 of 7 cases were evaluated as clinical success in red-red zone, 12 of 15 cases were assessed as clinical success in red-white zonal tear, stable reduction. Another case which is evaluated as clinical failure showed red-white zonal tear, unstable reduction and poor quality meniscal fragment. 5 cases showed variant degrees of tibio-femoral compartment symptom. In group II, red-white zone (9 cases) and white-white zone (14 cases) were treated as resection and got good results. Conclusion : Considering zone of tear, reducibility and quality of meniscal fragment before treatment will improve the success rate of meniscal repair.

• Journal of the Korean Arthroscopy Society
• /
• v.6 no.2
• /
• pp.150-155
• /
• 2002

Purpose : The purpose of this study was to evaluate the clinical results of meniscal repair using the bioabsorbable devices. Materials and Methods : From 1998, 21 meniscal repairs were underwent using the bioabsorbable devices and followed more than 1 year. The Meniscus $Arrow^{\circledR}$(Bionx) and the Meniscal $Fastener^{\circledR}$(Mitek) had been applied. The indication for meniscus refixation was an unstable longitudinal tear in the posterior horn of the medial or lateral meniscus. Concurrent ACL reconstruction with meniscal repair was performed on 9 knees. The clinical result was evaluated using Lysholm knee score. Result : The average Lysholm knee scores for all patients improved from 56 preoperatively, to 89 postoperatively. The type of the device were not significantly related to clinical outcome or Lysholm knee score. But the concurrent ACL reconstruction group and the patients treated within 8 weeks had better clinical result than the others. Conclusion : The all-inside meniscal repair technique using bioabsorbable devices can be considered to be an useful method in the well selected patients and concurrent ACL reconstruction surgery.