• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.478-487
• /
• 1996

A " plucking rolls device" was developed in this study to improve the quality of harvested tea leaves. In this report, the outline of the system and the results of performance experiments in our laboratory are discussed. Tow kinds of performance experiments were carried out. The first experiment checked harvesting accuracy by using a plucking unit that was developed for harvesting machine installation. The second experiment was a harvesting experiment which utilized a fron bar in order to prevent cutting of the tea buds which had been a problem in precious experiments . As a results of the first experiments , it was confirmed that selective harvesting obtained high quality tea leaves. but a cutting problem that, when the harvesting seed was faster than the working speed, which was non-selective harvesting , was also seen. In the second experiment, the cutting rate decreased to a maximum of 50% level, when tea buds most bent ahead by the front bar. The effect was seen that cutt ng problem was alleviated from this.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.9
• /
• pp.668-673
• /
• 2002

The sources of wayside noise for the high -speed train are the aerodynamic noise, rolling noise and power unit noise. We should know the major source to control noise radiated from train. In this paper, we present the test results on the wayside noise and the vibration of the rail/sleeper during the passing of Korean Train Express (KTX). It turns out that the major noise sources for KTX are the rolling noise and power unit noise at 300 km/h. Generally, the noise attenuation with distance is independent of train speed. However, the test results show that in the near field the noise levels decrease by about 5~6 ㏈(A) per doubling of distance at speed in the range of 50~120 km/h and about 3~4 ㏈(A)/d.d at 300 km/h.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.965-966
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.529-530
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1569-1570
• /
• 2013

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.113-126
• /
• 1992

Recently the multi-kind, small-amount manufacturing system has been replacing the mass manufacturing system, and domestic machining inustry also is eager to absorb the new technology because of its high productivity and cost reduction. The optimization of the cutting condition has been a vital problem in the machining industry, which would help increase the productivity and raise the international competitiveness. It is intended in this study to investigate the machining costs per unit time which is essential to the analysis of the optimal cutting condition, to computer the cutting speed that lead to the minimum machining costs and the maximum production to suggest the cutting speed range that enables efficient speed cutting, and to review the machining economy in relation to cutting depth and feed. Also considered are the optimal cutting speed and prodution rated in rrelation with feed. It is found that the minimum-cost cutting speed increases and the efficient cutting speed range is reduced as machining cost per unit time increases since the cutting speed for maximum production remains almost constant. The machining cost is also lowered and the production rate increases as the feed increases, and the feed should be selected to satisfy the required surface roughness. The machining cost and production rate are hardly affected by the cutting depth if the cutting speed stays below 100m/min, however, they are subject to change at larger cutting depth and the high-efficient speed range also is restricted. It can be established an adaptive optimal cutting conditions can be established in workshop by the auto-selection progam for optimal operation. It is expected that this method for choosing the optimal cutting conditions might contribute to the improvement of the productivity and reduced the cost. It is highly recommended to prepare the optimal cutting conditionthus obtained for future use in the programing of G-function of CNC machines. If proper programs that automatically select the optimal cutting conditions should be developed, it would be helpful to the works being done in the machine shops and would result in noticeable production raise and cost reduction.

• Tribology and Lubricants
• /
• v.21 no.5
• /
• pp.201-208
• /
• 2005

This paper presents the FEM analysis on the contact behavior characteristics of mechanical face seals in a small hydro-power turbine. Especially, the axial displacement and contact normal stress between a seal ring and a seal seat of a primary sealing unit have been analyzed as functions of rotating speed of a hydro-turbine, sealing gap, water and cooling fluid temperature. Those are strongly related to a leakage of water and wear between a seal ring and a seal seat. The FEM computed results present that the rotating speed of a hydro-turbine may be kept less than 800 rpm, and the sealing gap in a primary sealing unit is restricted $0.5\~5$. The coolant temperature in which is most influential parameter to the contact behaviors of a sealing unit may be kept less than $15^{\circ}C$ for a safe operation of a sealing unit without a leakage and wear.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.132-137
• /
• 2011

Many studies are being conducted to improve high speed, light weight and safety of passenger. To improve safety of rolling stock, safety of running performance is most important, and optimizing flow lubrication in driving gear is essential. This study simulates lubricant flow change in driving gear casing which is splashed by the surface of low speed gear teeth following rotational direction of driving gear unit for EMU by using CFD analysis, and based on analysis detail, non-load actual test is conducted for similar driving condition to find out suitability of analysis, selection of lubricate and stability of driving gear.

• Journal of computational fluids engineering
• /
• v.16 no.4
• /
• pp.110-115
• /
• 2011

A modern optical fiber manufacturing process requires the sufficient cooling of glass fibers freshly drawn from the heated and softened silica preform in the furnace, since the inadequately cooled glass fibers are known to cause improper polymer resin coating on the fiber surface and to adversely affect the product quality of optical fibers. In order to greatly enhance the fiber cooling effectiveness at increasingly high fiber drawing speed, it is necessary to use a dedicated glass fiber cooling unit with helium gas injection between glass fiber drawing and coating processes. The present numerical study features a series of three-dimensional flow and heat transfer computations on the cooling gas and the fast moving glass fiber to analyze the cooling performance of glass fiber cooling unit, in which the helium is supplied through the discretely located rectangular injection holes. The air entrainment into the cooling unit at the fiber inlet is also included in the computational model and it is found to be critical in determining the helium purity in the cooling gas and the cooling effectiveness on glass fiber. The effects of fiber drawing speed and helium injection rate on the helium purity decrease by air entrainment and the glass fiber cooling are also investigated and discussed.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.1
• /
• pp.43-55
• /
• 2001

A continuously variable transmission(CVT) mechanism composed of one differential gear unit and one continuously variable unit(CVU) can be classified according to the coupling of CVU and the direction of power flows. The mechanism has many advantages which are the decrease of CVT size, the increase of overall efficiency, the extension of speed ratio range and generation of geared neutral. The CVT mechanism considered here is the input coupled type which combines the functions of a 2K-H I type differential gear unit and a V-belt type CVU. One shaft of the CVU is connected directly to the input shaft and another shaft of it is linked to the differential gear unit. It is shown that some fundamental relations(speed ratios, power flows and efficiencies) for twelve mechanisms previously described are valid by various experimental studies, six of them produce a power circulation and the others produce a power split. Some useful comparisons between theoretical analysis and experimental results are presented. General properties also are discussed, which connect following power flow modes : (a) power circulation mode; (b) power split mode.