• Journal of the Korean Magnetics Society
• /
• v.1 no.1
• /
• pp.30-36
• /
• 1991

A measurement system for magnetic anisotropy was built. The torque acting on the disc or sperical samples placed in uniform magnetic field was detected with a capacitive transducer which is connected with a transformer ratio-arm bridge. The output of the bridge was amplified with a lock-in amplifier. The cubic anisotropy constant for (100) of 3% Si-Fe was $3.3{\times}10^{4}\;J/m^{3}$. The calibration for the system was carried out with the shape anisotropy of a thin Ni wire.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.6 s.39
• /
• pp.29-34
• /
• 2006

Propeller type pump has been widely used for pumping water in agricultural and manufacturing industry. Since a propeller type pump contains a screw impeller inside a circular casing, the numerical analysis becomes complex. However, the accurate prediction of viscous flow is essential for computing hydrodynamic performances. To analysis the flow and the performance of the propeller type pump, the present work has solved 3D incompressible RANS equations on the multiblocked grid. From the present calculation, small amount of flow separation was shown near hub and the flow was recovered to nearly uniform inflow after one diameter downstream. Torque and thrust coefficient were computed and compared with experiments.

• Journal of Mechanical Science and Technology
• /
• v.15 no.1
• /
• pp.35-43
• /
• 2001

Both tensile and tear properties of short-fiber reinforced Chloroprene rubber have been studied as functions of the fiber aspect ratio and fiber content. Both properties increased when both the fiber aspect ratio and fiber content were increased. The fiber reinforced rubbers exhibited maximum values of these properties at a fiber aspect ratio of about 300. When the fiber aspect ratio exceeds 400, the mechanical properties decreased with the fiber content because of the non-uniform dispersion of fibers. The tensile modulus was compared with the prediction by the Halpin-Tsai equations for randomly oriented cases. A bonding agent was used in the fiber treating process. It was found that the ultimate tensile strength, torque, tearing energy and tensile modulus of the rubbers with treated fibers were much higher than those with untreated ones.

• Proceedings of the KIEE Conference
• /
• 1998.07b
• /
• pp.544-545
• /
• 1998

In industry and engineering, the tensile measurement of single crystal metal material such as the uniform change, surface structure and the tensile torque of the material is not easy to obtain by current the tensile measurement methods. In this paper, we have implemented a tensile system which can acquire tensile information in real time.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.52-58
• /
• 2017

Graphene oxide (GO)/carboxylated styrene-butadiene rubber (XSBR) nanocomposites with various contents of GO were prepared by a latex compounding method. It has been confirmed that the functional groups of GO and the hydrogen bonds between GO and XSBR are existed. It can be seen that the scorch time ($t_{s2}$), which is the measurement of incipient vulcanization of rubber, showed a delay after the addition of GO. Field emission scanning electron microscopy was employed to confirm the uniform dispersion of filler in the matrix. Indeed, with increasing fillers loading, the torque, tensile strength, thermal stability and crosslink density of obtained nanocomposites were improved. These results were correlated to the better dispersion of fillers through the rubber matrix.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.5
• /
• pp.42-47
• /
• 2012

Newly updated wing shape to apply small vertical wind turbine is tested with digital wind tunnel in this study. Digital wind tunnel is designed to reduce length of wind tunnel and also to maximize its area of test section. Same DC fans of ninety six are installed in the end side of its rectangular duct and air can be blown out to the other side to have uniform flow with same electricity power. New wing is concluded using experimental plan and analysis with 4-parameters and 3-levels, and tested with digital wind tunnel. It shows better performance in lift to drag ratio, and can applied to the wind turbine for the higher torque and lower thrust.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2544-2545
• /
• 2001

In industry and engineering, the tensile measurement of single crystal metal material such as the uniform change, surface structure and the tensile torque of the material is not easy to obtain by current the tensile measurement methods. In this paper, we have implemented a tensile system which can acquire tensile information in real time.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.40-42
• /
• 1998

Magnetization distribution in the ring magnet for BLDC motor is generally nonuniform because the structure of mutipole magnetizer is not symmetry and the air gap is not uniform. In this paper, the effect of the nonuniform magnetization on characteristics of the motor such as torque ripple, unbalanced force and current is examined. Time stepped finite element method is used for electromagnetic field analysis.

• Journal of Magnetics
• /
• v.21 no.4
• /
• pp.491-495
• /
• 2016

We developed an embedded Object-Oriented Micromagnetic Frame (OOMMF) script schemes for more flexible simulations for complex and dynamic mircomagnetic behaviors. The OOMMF can be called from any kind of softwares by system calls, and we can interact with OOMMF by updating the input files for next step from the output files of the previous step of OOMMF. In our scheme, we set initial inputs for OOMMF simulation first, and run OOMMF for ${\Delta}t$ by system calls from any kind of control programs. After executing the OOMMF during ${\Delta}t$, we can obtain magnetization configuration file, and we adjust input parameters, and call OOMMF again for another ${\Delta}t$ running. We showed one example by using scripting embedded OOMMF scheme, tunneling magneto-resistance dependent switching time. We showed the simulation of tunneling magneto-resistance dependent switching process with non-uniform current density using the proposed framework as an example.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.1
• /
• pp.18-25
• /
• 2017

This study deals with numerically comparing performance according to rudder shape called 'Twisted rudder and Wavy twisted rudder'. In comparison with conventional rudder, rudder with wavy shape has showed a better performance at high angles of attack($30^{\circ}{\sim}40^{\circ}$) due to delaying stall. But most of study concerned with wavy shape had been performed in uniform flow condition. In order to identify the characteristics behind a rotating propeller, the present study numerically carries out an analysis of resistance and self-propulsion for KCS with twisted rudder and wavy twisted rudder. The turbulence closure model, Realizable $k-{\epsilon}$, is employed to simulate three-dimensional unsteady incompressible viscous turbulent and separation flow around the rudder. The simulation of self-propulsion analysis is performed in two step, because of finding optimization case of wavy shape. The first step presents there are little difference between twisted rudder and case of H_0.65 wavy twisted rudder in delivered power. So two kind of rudders are employed from first step to compare lift-to-drag ratio and torque at high angles of attack. Consequently, the wavy twisted rudder is presented as a possible way of delaying stall, allowing a rudder to have a better performance containing superior lift-to-drag ratio and torque than twisted rudder at high angles of attack. Also, as we indicate the flow visualization, check the quantity of separation flow around the rudder.