• Journal of the Mineralogical Society of Korea
• /
• v.9 no.1
• /
• pp.35-42
• /
• 1996

Polycrystalline ZrH2 in tetragonal crystal system has been compressed in a modified Bassett-type diamond anvil cell up to 36.0 GPa at room temperature. X-ray diffraction data did not indicate any phase transitions at the present pressure range. The pressure dependence of the a-axis, c-axis, c/a and molar volume of ZrH2 was determined at pressures up to 36.0 GPa. Assuming the pressure derivative of the bulk modulus (K0') to be 4.11 from an ultrasonic value on Zr, bulk modulus (K0) was determined to be 160Gpa by fitting the pressure-volume data to the Birch-Murnaghan equation of state. Same sample was heated at $500^{\circ}C$ at the pressure of 9.8 GPa in a modified Sung-type diamond anvil cell. Unloaded and quenched sample revealed that the original tetragonal structure transforms into a hexagonal structured phase with a zero-pressure molar volume change of ~115.5%.

• Journal of Mechanical Science and Technology
• /
• v.16 no.2
• /
• pp.175-181
• /
• 2002

A new polariscope system involving two rotating optical elements and a digital camera for whole field fringe analysis allows automated data to be acquired quickly and efficiently. The developed phase measuring technique that uses eight images through a circular polariscope is presented for the digital measurement of isochromatics and isoclinics, respectively, from photoelastic fringes in a circular disk under diametric compression. Isochromatics can directly be obtained using wrapped isoclinic phases calculated by the arc tangent operator which is the four-quadrant operator from -$\pi$ to $\pi$. It is not required to unwrap isoclinic phases for the calculations of isochromatics. Unwrapped isoclinics are directly determined from isochromatic parameters. Distributions of digitally determined isoclinics are in close agreement to manual measurements. The errors which would appear in unwrapping process of isoclinics can be avoided in the determination of isochromatics.

• Computers and Concrete
• /
• v.12 no.1
• /
• pp.79-90
• /
• 2013

In this study, dynamic characteristics such as natural frequencies, mode shapes and damping ratios of RC frame is determined for different construction stages using Operational Modal Analyses method under ambient vibration. Full scaled, one bay and one story RC frames are selected as an application for different construction stages such as plane, brick in-filled and brick in-filled with plaster. The RC frame is vibrated by natural excitations with small impact effects and the response signals are measured using sensitive accelerometers during ambient vibration tests. Measurement time-frequency span and effective mode number are determined by considering similar studies in literature. Sensitive seismic accelerometers are used to collect signals obtained from the experimental tests. To obtain experimental dynamic characteristics, output-only system identification technique is employed namely; Enhanced Frequency Domain Decomposition technique in the frequency domain. It is demonstrated that the ambient vibration measurements are enough to identify the most significant modes of RC frames.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.22 no.50
• /
• pp.65-73
• /
• 1999

Most psychophysical studies in manual material handling (MMH) have paid more attention to two-handed MMH activities than to one-handed MMH activities. Also, studies are involved only with single MMH activities - lifting, lowering, carrying, holding, pushing or pulling. Very few studies are reported on the determination of workers' capacities for combinations of one-handed MMH activities (lifting a box, then carrying the box, and lowering the box). The objective of this study was to find the psychophysical and physiological responses of human subjects from a simulated industrial task involving one-handed and two-handed combined tasks. The capacities that were determined as the maximum acceptable weight workloads for 1 hr work period for one-handed and two-handed combined tasks - lifting a box from floor to knuckle height, carrying the box for 4.3 m, and lowering the box from knuckle to floor height - were determined psychophysically under three frequencies: six handlings per minute, one handling per minute and one handling per five minutes. In addition to maximum acceptable weight, heart rate and RPE values on wholebody, back, and arm were also measured as responses.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.279-286
• /
• 2000

Magnetic field dependence of magnetization reversal in Co/Pt multilayers has been quantitatively investigated. Serial samples of Co/Pt multilayers have been prepared by dc-magnetron sputtering under various Ar pressure. Magnetization reversal was monitored by magnetization viscosity measurement and direct domain observation using a magneto-optical microscope system, and the wall-motion speed and the nucleation rate R were determined using a domain reversal model based on time-resolved domain reversal patterns. Both and R were found to be exponentially dependent on the reversing applied field. From the exponential dependencies, the activation volumes of the wall motion and nucleation could be determined based on a thermally activated relaxation model, and the wall-motion activation volume was revealed to be slightly larger than the nucleation activation volume.

• Journal of the Korea Safety Management & Science
• /
• v.19 no.2
• /
• pp.69-80
• /
• 2017

This study is analyse method for Industrial disester prevention of E-9 foreign workers. To do this, We adapted tp TRIZ 's creative problem solving theory and AHP, QFD. TRIZ is determined some parameters for problem solving and selected the inventive principles for each parameters. So, We made new parameters and inventive principles under theory of the TRIZ process for reduced to the foreign worker's disaster rate. After, The derived parameters and the inventive principles are used to evaluate the importance of factors through the AHP, and determine the weight of the relation through QFD expansion. Finally. this paper applies statistical data according to the determined model process, analyzes the result and proposes improvement method for the prevention of disaster of foreign workers.

• Journal of Magnetics
• /
• v.5 no.4
• /
• pp.116-119
• /
• 2000

Magnetic field dependence of magnetization reversal in Co/Pt multilayers was quantitatively investigated. Serial samples of Co/Pt multilayers were prepared by dc-magnetron sputtering under various Ar pressures. Magnetization reversal was monitored by magnetization viscosity measurement and direct domain observation using a magneto-optical microscope system, and the wall-motion speed V and the nucleation rate R were determined using a domain reversal model based on time-resolved domain reversal patterns. Both V and R were found to be exponentially dependent on the applied reversing field. From the exponential dependencies, the activation volumes for wall motion and nucleation could be determined, based on a thermally activated relaxation model, and the wall-motion activation volume was found to be slightly larger than the nucleation activation volume.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.6
• /
• pp.845-851
• /
• 2015

Load shedding is a last measure to avoid nationwide cascading collapses of power system by removing the pre-determined amount of loads from the main grid. In Korea, SPS(Special Protection System) is prepared to keep the power system stability from the extreme contingency of the critical transmission line losses. Among them, we need to pay attention to 765kV T/L’s because they have great influence on the total system stability. According to the present SPS operating guide, the total loads of 1,500MW should be removed through 2 step under-voltage load shedding(UVLS) scheme in case of 765kV T/L’s contingencies. However, it is not clear to defined how to determine the typical load reduction amounts for each case. This paper proposes a method to estimate appropriate amounts of load shed for 765kV T/L’s contingencies by analyzing the relevant national and international standards.

• Journal of Biosystems Engineering
• /
• v.16 no.4
• /
• pp.346-354
• /
• 1991

Turning behavior of tractor-trailer system was studied to guide the tractor and trailer. Based upon kinematic relationship between the tractor and the trailer, a mathematical model was developed and analyzed by computer simulation. A field test was carried out to verify the mathematical model. Following conclusions were drawn from this study. 1. A mathematical model and a simulation program for turning behavior of tractor-trailer system were developed. 2. The results of the field tests showed that the RMS errors were less than 0.33m and the mathematical model based upon kinematic relationship can be used for mapping guidance system for tractor and trailer. 3. As the steering angle was increased, the turning radius was decreased. When the tractor travelled at the low speed, the travel speed of the tractor did not affect turning radius but did affect running time and stability for steering. 4. When the tractor travelled under the critical velocity, the towed trailer followed smoothly. When the the tractor travelled faster than the critical velocity, the towed trailer oscillated. The critical velocity was determined from the specification of the tractor and the trailer.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.4
• /
• pp.99-107
• /
• 2000

In this study, a static and dynamic characteristics analysis system for machine tool spindle systems with 3 lobe sliding bearing is developed based on Timoshenko theory, finite element method and windows programming techniques. And the characteristics value of 3 lobe sliding bearing such as eccentricity ratio, attitude angle, friction coefficient , stiffness coefficients, damping coefficients and so on, are determined by using the thermal equilibrium conditions of spindle systems. Since the developed system has various analysis modules related to static deformation analysis, modal analysis, frequency responses analysis and so on, it can be utilized to perform systematically the design an devaluation process of spindle systems with 3 lobe sliding bearing under windows GUI environment.