• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.469-474
• /
• 2001

The feasibility of a oil-free motor-driven two-stage centrifugal compressor supported by air bump bearings is investigated. This centrifugal compressor is driven by 75kW motor at an operating speed of 39,000RPM md a pressure ratio of the compressor is up to 4. The analysis is performed, based upon bearing equilibrium position, bearing stiffness, Campbell diagram, unbalance response and stability. It is demonstrated in this paper that air bump bearings can be adopted well to a oil-free motor-driven centrifugal compressor.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.567-571
• /
• 1989

This paper describes the improvement of thermal power plant turbine control system by analyzing nonlinear characteristics. The turbine control depends on the frequency variation and boiler condition. The nonlinearity of turbine control is the result of governor/valve properties, steam condition and boiler thermal unbalance. Nonlinear analysis is divided into two; main steam valve position - turbine output anal governor response. Of course, every analysis must be done on considering plant operating condition. In this paper, after analyzing turbine control nonlinearity by numerical method and actual results, the sensitive operating load which corresponds to frequency is proposed, on guarranteed boiler stability. This idea is implemented at Pyung Tack thermal power plant, and the practical results are showed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.16 no.5
• /
• pp.39-49
• /
• 1992

The dynamic design object of rotor system is to optimize the system in stability at the operating speed, unbalance response in the vicinity of the rotor critical speed, bearing weighting and system weighting. In conventional optimization method, designers have to set mathematical modeling, such as objective function, constraints and design parameters, strictly and quantitavely. But in actual design process, they do not treat all of these values strictly and some of them are somehow "fuzziness". So, considering boundary conditions of seal diameter, clearance, and length in a typical double suction centrifugal pump is fuzzy, this paper is considered fuzzy in constraints. Fuzzy method is used .alpha.-level cut method. Then, the optimum dimensions of seal according to values are obtained and vibration characteristics are investigated.estigated.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.309-314
• /
• 2001

The balance of high speed spindle system with high precision rotation like grinding machine is very important. Traditionally, we use trial and error method to balance the spindle. It takes much time. So we are developing the automatic balancing equipment being used in the grinding machine. The balancing head we develop is wireless. It will be used high-speed grinding machine. We use influence coefficient method to control the automatic balancer. Experiments are based on automatic and manual balancing. We perform test of the vibration filter. It helps to remove noise. The filter and experiments with automatic balancing controller show that automatic balancing control can be successfully achieved with the quick response and good stability characteristics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.547-550
• /
• 1997

The dynamic behavior of rotor-bearing system has been investigated using finite element method. A procedure is presented for dynamic modeling of rotor-bearing system which consist of shaft elements, rigid disk, flexible bearing and support structures. A finite element model including the effects of rotary inertia, shear deformation, gyroscopic moments is developed. Linear stiffness and damping coefficient are calculated for 3 lobe sleeve bearing. The whirl frequency, mode shape, stability and unbalance response of rotor system included effect of bearing coefficient and support structures are calculated.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.152-159
• /
• 2001

In this paper it is intended to set-up a sound model of the 60,000rpm 100kW prototype APU gas turbine rotor-bearing system, and particularly to investigate the influences of the tie shaft on the rotordynamic characteristics of the entire APU gas turbine rotor-bearing system, employing the dual shaft model. Firstly, a mock-up APU rotor has been constructed to test and verify the model. Analytical natural frequency results have agreed with the corresponding modal test ones to within 5% difference. Then, the rotordynamic characteristics of the prototype APU rotorbearing system have been investigated. Natural vibration and unbalance response analyses results have shown that the inner tie shaft resonance can cause high enough vibration of the outer main rotor shaft. This could be a concern as the rotor journals operate on very thin air film at high speed. It is concluded as a conservative design practice that the inner tie shaft should be explicitly modeled in the rotordynamic analysis of the APU rotor-bearing system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.936-941
• /
• 2001

This paper deals with the design of oil-tree motor-driven two-stage centrifugal compressor supported by air-lubricated multi-leaf foil bearings. The design of this compressor is performed, based upon prediction of critical speeds, load capacity, and stability. It is demonstrated in this paper that multi-leaf foil bearings can be adopted to satisfactorily support this centrifugal compressor.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.37-44
• /
• 2002

The dynamic behavior of rotor-bearing system has been investigated using finite element method. A procedure is presented for dynamic modeling of rotor-bearing system which consists of shaft elements, rigid disk, flexible bearing and support structure. A finite element model including the effects of rotary inertia, shear deformation, gyroscopic moments is developed. Linear stiffness and damping coefficients are calculated for 2 lobe sleeve bearing. The whirl frequency, mode shape, stability and unbalance response of rotor system including effects of bearing coefficient and support structures are calculated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.8 s.227
• /
• pp.1212-1220
• /
• 2004

The structural unbalance mass and laundry are the important sources of the severe vibrations of automatic washing machines. In this paper, a mathematical model is developed for the dynamic analysis of the vertical axis automatic washing machines of pulsator-type. In the model, the rigid body motion of tub assembly is represented by six degrees of freedom and the dynamics of automatic hydraulic balancer is represented by one degree of freedom. The fundamental elastic modes of the tub shell and four suspension bars are also taken into account in the mathematical model, based on analytical and experimental modal analysis results. The 12 degrees of freedom equations of motion are derived by using the Lagrange's equations and the present dynamic model is evaluated by comparing the numerical simulation results with experimentally measured data.

• 한국기계연구소 소보
• /
• s.18
• /
• pp.5-19
• /
• 1988

Finite element scheme to analyze the vibration characteristics of the axisymmetric rotor system is developed. The rotor system of a large washer-extractor is analyzed as an example. Natural frequency obtained by FEM is in good agreement with experimental one by impact test. Also, parametric studies using FEM code developed are carried out for the investigation of the effects of the radii of the axis and the cylinder on the stiffness and the critical speed of the system. Larger radius of the axis makes the system stiffer and increases the critical speed at which the unbalance response has its maximum value. Whereas, the stiffness and the critical speed decrease at first and then increase as the radius of the cylinder increases.