• 반도체디스플레이기술학회지
• /
• 제13권3호
• /
• pp.51-55
• /
• 2014

Ni-CNT(Carbon Nanotubes) composite coating is often used for the surface treatment of mechanical/electronic devices to improve the properties of the Ni coating. For the Ni-CNT coating, the dispersion of CNT fibers is a critical process. In this study, ultrasonic treatment instead of the conventional ball milling was attempted as a dispersion method for the electroless Ni-CNT coating. SEM-EDX analysis was performed and contact angle, sheet resistance, and micro-hardness were measured. Results showed that the ultrasonic treatment was comparable to the ball milling, as a dispersion method, but the difference was negligible. However, combined ball milling and ultrasonic treatment(double treatment) showed much improved micro-hardness value, above 350Hv(close to the value obtained by the Ni-CNT electroplating). In addition, electroless Ni-CNT(double-treated) coatings formed on the thin Ni film deposited by the electroless plating(double coating) showed better mechanical properties. Thus, double treatment and double coating are suggested as an improved electroless Ni-CNT coating method.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.597-603
• /
• 2009

The hydrogen reduction behavior of ultrasonic ball-milled $WO_3-CuO$ nanopowder, which is highly related with micro-pore structure, was investigated by thermogravimetry(TG) and hygrometry system. EDS and TEM results represented that the ultrasonic ball-milled $WO_3-CuO$ nanopowder consisted of the agglomerates which was confirmed as a homogeneous mixture of $WO_3$ and CuO particles. It was found that the reduction reaction of CuO was retarded by initial micro-pores which are smaller than 40 nm in the ultrasonic ball-milled $WO_3-CuO$ nanopowder. The earlier agglomeration of Cu particles at comparably low temperature decreased the volume of micro-pores in the $WO_3-CuO$ nanopowder which caused the retardation of $WO_3$ reduction reaction. These results clearly explain that the micro-pore structure significantly affected the reduction reaction of $WO_3$ and CuO in the $WO_3-CuO$ nanopowder.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.203-204
• /
• 2008

In this study, in order to develop the multilayer piezoelectric actuator and ultrasonic resonator, PMN-PNN-PZT ceramics were fabricated by the variations of ball size at sintering temperature of $900^{\circ}C$ and their piezoelectric and dielectric characteristics were investigated as a function of the variations of ball size. When the ball size was 3mm$\phi$, density, dielectric constant$({\varepsilon}r)$, electromechanical coupling factor(kp) and piezoelectric d constant$(d_{33})$ were increased. At the ball size of 3mm$\phi$, the specimen showed the optimum values of density=7.909g/$cm^3$, kp=0.592, Qm=1292, $d_{33}$=368pC/N, $\varepsioln_r$=1502, respectively.

• Carbon letters
• /
• 제13권2호
• /
• pp.121-125
• /
• 2012

In the present work, exfoliated graphite nanoplatelets (EGN) of 1 ${\mu}m$ in average particle size, which were prepared by heating at $900^{\circ}C$ and then subjected to ultrasonic, ball-milling, and vibratory ball-milling techniques, were uniformly incorporated into phenylethynyl-terminated polyimide (PETI-5) resin. The fracture surface morphology and the electrical resistivity of the EGN/PETI-5 composites were investigated. The results showed that the fracture surfaces and the electrical resistivity strongly depended on the EGN content. The fracture surfaces became more ductile and roughened with increasing EGN and the electrical resistivity was gradually decreased with increased EGN loading, indicating the percolation threshold at 5 wt% EGN.

• 한국분말재료학회지
• /
• 제26권3호
• /
• pp.201-207
• /
• 2019

Tungsten heavy alloys (W-Ni-Fe) play an important role in various industries because of their excellent mechanical properties, such as the excellent hardness of tungsten, low thermal expansion, corrosion resistance of nickel, and ductility of iron. In tungsten heavy alloys, tungsten nanoparticles allow the relatively low-temperature molding of high-melting-point tungsten and can improve densification. In this study, to improve the densification of tungsten heavy alloy, nanoparticles are manufactured by ultrasonic milling of metal oxide. The physical properties of the metal oxide and the solvent viscosity are selected as the main parameters. When the density is low and the Mohs hardness is high, the particle size distribution is relatively high. When the density is high and the Mohs hardness is low, the particle size distribution is relatively low. Additionally, the average particle size tends to decrease with increasing viscosity. Metal oxides prepared by ultrasonic milling in high-viscosity solvent show an average particle size of less than 300 nm based on the dynamic light scattering and scanning electron microscopy analysis. The effects of the physical properties of the metal oxide and the solvent viscosity on the pulverization are analyzed experimentally.

• Composites Research
• /
• 제37권3호
• /
• pp.150-154
• /
• 2024

본 연구는 대두 부산물인 대두피로부터 나노 섬유화 셀룰로오스를 추출하고, 다른 나노 섬유화 기법으로 제작된 대두피 나노 섬유화 셀룰로오스와 비교 평가를 수행하였다. 건조 대두피를 분쇄하여 마이크로미터 크기의 분말을 제조한 후, NaOH와 HCl을 이용하여 대두피로부터 마이크로 셀룰로오스를 분리하였다. 초음파 분산 및 볼밀링을 통하여 나노미터 크기의 셀룰로오스를 추출하는데 성공하였다. 대두피 나노 섬유화 셀룰로오스는 직경 60-100 nm, 길이 0.3-1.0 ㎛의 크기를 가져 다른 나노 섬유화 기법으로 대두 나노 셀룰로오스와 직경은 유사한 수준이나 길이는 1/5 수준임을 확인하였다.

• 한국세라믹학회지
• /
• 제44권5호
• /
• pp.148-150
• /
• 2007

A process to synthesize $La_{0.8}Sr_{0.2}CrO_3$ (LSC), which is a promising material for use as a separator in a soild oxide fuel cell, is investigated in this study. LSC powders without secondary Phases could be synthesized with ultrasonic spray pyrolysis and a heat treatment at $1200^{\circ}C$ for 20 h; however, it showed an average diameter of $0.6{\mu}m$ with a wide particle size distribution. On the other hand, LSC powders synthesized with spray pyrolysis at $800^{\circ}C$, heat-treated at $900^{\circ}C$ for 5 h, ball-milled and finally heat-treated again at $1200^{\circ}C$ for 20 h showed a smaller average diameter of $0.3{\mu}m$ and narrower size distribution. Very few particles above $0.5{\mu}m$ were found. Thus, a proper combination of the heat treatment and milling process after spray pyrolysis it determined to be very important in synthesizing fine and uniform LSC perovskite powders.

• Applied Microscopy
• /
• 제32권4호
• /
• pp.311-317
• /
• 2002

입자 크기에 따라 상전이 경로가 달라지며 매우 큰 응집체로 존재하는 gibbsite 분말과 같은 재료의 정량적인 전이 구조 분석의 전제로서 입자 크기가 선택적인 TEM 시편의 준비가 절실히 요구된다. 입자 크기 선택성을 실현한 TEM 시편 준비의 방법론을 확립하기 위한 방안으로서 본 실험이 전개되었다. 약 1 wt%의 gibbsite 원료 분말을 에탄올 용매에 혼합 한 뒤, ball-milling에 의해 조분쇄 처리를 하고 증류수에 1 : 19의 비로 희석된 분산 조제, Darvan C, 0.25 vol%의 첨가와 함께 ultrasonic 처리를 하여 gibbsite suspension을 만들었다. 제조된 gibbsite suspension의 누적 농도 변화 관찰에 의한 침강 시간의 조정 후 정적 침강 분리에 의해 nm 크기별로 분리된 TEM 시편을 만들 수가 있었다. 시편의 전체적인 양상은 SEM으로 관찰하였고 개개 입자들의 morphology 는 TEM으로 분석하였다. 또한, 공정 과정 중의 상변화 가능성을 검토하기 위해 XRD 분석을 실시하였다.

• 한국세라믹학회지
• /
• 제30권6호
• /
• pp.492-498
• /
• 1993

The pretreatment condition for uniform distribution of SiC whisker in A2O3-SiCw composites has been determined and the mechanical properties of the composites with various whisker contents have been measured. Good dispersion of the whisker can be obtained in a solution of pH=10.45 by ball milling and ultrasonic treatment. The relative density of hot pressed composites decreases with the whisker content up to 40vol%, but is found to be satisfactory, over 98% for all samples. The mechanical property of the composites is sensitive to the whisker dispersion. Uniform distributjion of the whisker is critical in order to guarantee good mechanical property.The samples containing 20~30vol% whisker show the best mechanical property within the studied range.

• 대한금속재료학회지
• /
• 제47권1호
• /
• pp.50-58
• /
• 2009

In this study, alumina matrix composites reinforced with carbon nanotubes (CNTs) were fabricated by ultrasonic dispersion, ball milling, mixing, compaction, and sintering processes, and their relative density, electrical resistance, hardness, flexure strength, and fracture toughness were evaluated. 0~3 vol.% of CNTs were relatively homogeneously dispersed in the composites in spite of the existence of some pores. The three-point bending test results indicated that the flexure strength increased with increasing volume fraction of CNTs, and reached the maximum when the CNT fraction was 1.5 vol.%. The fracture toughness increased as the CNT fraction increased, and the fracture toughness of the composite containing 3 vol.% of CNTs was higher by 40% than that of the monolithic alumina. According to observation of the crack propagation path after the indentation fracture test, a new toughening mechanism of grain interface bridging-induced CNT bridging was suggested to explain the improvement of fracture toughness in the alumina matrix composites reinforced with CNTs.