• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.81-82
• /
• 2007

The stochiometric mix of evaporating materials for the $CdGa_2Se_4$ single crystal thin films was prepared from horizontal furnace. To obtain the single crystal thin films, $CdGa_2Se_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperature were $630^{\circ}C\;and\;420^{\circ}C$, respectively. After the as-grown single crystal $CdGa_2Se_4$ thin films were annealed in Cd-, Se-, and Ga -atmospheres, the origin of point defects of single crystal $CdGa_2Se_4$ thin films has been investigated by PL at 10 K. The native defects of $V_{Cd},\;V_{Se},\;Cd_{int},\;and\;Se_{int}$ obtained by PL measurements were classified as donors or acceptors. And we concluded that the heat-treatment in the Cd-atmosphere converted single crystal $CdGa_2Se_4$ thin films to an optical p-type. Also, we confirmed that Ga in $CdGa_2Se_4$/GaAs did not form the native defects because Ga in single crystal $CdGa_2Se_4$ thin films existed in the form of stable bonds.

• Nuclear Engineering and Technology
• /
• 제55권3호
• /
• pp.958-967
• /
• 2023

This work studies the defect features in a dilute FeMnNi alloy by an Object Kinetic Monte Carlo (OKMC) model based on the "grey-alloy" method. The dose rate effect is studied at 573 K in a wide range of dose rates from 10^-8 to 10^-4 displacement per atom (dpa)/s and demonstrates that the density of defect clusters rises while the average size of defect clusters decreases with increasing dose rate. However, the dose-rate effect decreases with increasing irradiation dose. The model considered two realistic mechanisms for producing <100>-type self-interstitial atom (SIA) loops and gave reasonable production ratios compared with experimental results. Our simulation shows that the proportion of <100>-type SIA loops could change obviously with the dose rate, influencing hardening prediction for various dose rates irradiation. We also investigated ways to compensate for the dose rate effect. The simulation results verified that about a 100 K temperature shift at a high dose rate of 1×10^-4 dpa/s could produce similar irradiation microstructures to a lower dose rate of 1×10^-7 dpa/s irradiation, including matrix defects and deduced solute migration events. The work brings new insight into the OKMC modeling and the dose rate effect of the Fe-based alloys.

• 한국항공운항학회지
• /
• 제26권4호
• /
• pp.116-121
• /
• 2018

According to the incresement of aging aircraft, Republic of Korea Air Force (RoKAF) conducted a teardown inspection of aircraft's EWIS (electrical wiring interconnection system) to determine the status of deterioration and the influence of failure occurrences due to it. The inspected aircraft were the retired fighter jets that had been used for more than 40 years. By analyzing defect type and the defect tendency, RoKAF can establish the necessary measures for the usage extension of their fleet and furthermore, the analysis results can be used as a basic data for the preparation of it's aircraft aging. EWIS inspection was done throughout careful visual inspection technique by removing all the ducts and pipes located in the fuselage and wings. For the aircraft wiring where no damage was found, the elongation tests were performed to determine the deterioration of wiring according to the location of the aircraft. The connectors, which is the main cause of intermittent failure, were completely disassembled and inspected for internal damage such as corrosion, abrasion, and traces of foreign objects. The detected defects were classified into 4 severity levels based on the type of damage, and the classified defects were weighted according to the criticality which may affects to it's system to establish the action plan.

• Korean Chemical Engineering Research
• /
• 제49권3호
• /
• pp.297-300
• /
• 2011

Mechanical exfoliation 방법에 의해 제작된 그래핀(Few Layer Graphene: FLG) 소자에 양성자를 조사하여 의도적으로 결함의 수를 증가시켰다. 그 후 공기중에 노출되었을 때와 진공상태에서 보관한 후에 측정된 전기적 특성을 확인하였다. 또한 UV에 노출시킨 후와 진공상태에서 열처리를 진행한 후에 전기적 특성의 변화들을 관찰하였다. 진공상태에서 보관한 그래핀 소자는 표면에 흡착되어 도펀트로 작용하게되는 species의 수가 감소하기 때문에 전류가 감소하는 결과를 나타내었다. UV에 노출된 상태에서는 오존에 의한 영향으로 약간의 전류 상승이 일어나지만 케리어의 이동도가 감소하게 된다. 반면 진공상태에서 열처리 후에는 전류는 매우 감소하게 되지만 결함과 도펀트에 의한 케리어 산란 현상이 감소하게 되므로 이동도는 크게 증가하게 된다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권5호
• /
• pp.198-205
• /
• 2005

Many precedent investigations hate been made for the reliable assessment of the insulation state of large power apparatus for which partial discharge detection is one of tile plausible way. In this work, experimental investigations have been carried out to make the comparison on the PD(partial discharge) pattern analysis related to the five different types of artificial defects such as SFMP (Single Free Moving Particle), MFMP (Multi Free Moving Particle), Void, CFP (Conductor-Fixed Protrusion), EP (Enclosure Protrusion). For each PD pattern, PD detection has been done by tee different types of PD sensors such as HFCT(High Frequency Current Transformer), AE(Acoustic Emission) and UHF(Ultra High Frequency). And, in addition, frequency spectrum by the UHF sensor has been also made for each defect respectively. As a result, it is observed that the possibility of obtaining PD pattern based on PRPD(Phase Resolved Partial Discharge) in connection with the defects tinder investigation is dependant on the type of the sensor while the spectrum analysis is always successful to be achieved for every defect. Therefore, it could be suggested that the nature of PD source can be identified more distinctively when the conventional PRPDA is combined with spectrum analysis.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.187-188
• /
• 2019

The supply of apartments has continuously increased, and the housing supply rate has exceeded 100 percent and the demands and standards of tenants have also been raised as technology has developed. This has led to the conflict and caused social and economic losses. In this study, the case investigation and research methods of the prior research are analyzed as the basis for identifying the defects cases of causes and influences occurring in the apartment building. To analyze various studies, we divided the prior research into the defect management process and the study on the type of defects and countermeasures, and investigated the features and limitations. Future research will be conducted on apartment buildings within 10 years of completion among conglomerate's nationwide apartments to compensate for the limitations of prior research. In addition, AHP static method and relational chart will be used to identify the relationship between the type of defect and the cause and the importance of the influencing factors.

• 한국세라믹학회지
• /
• 제56권3호
• /
• pp.302-307
• /
• 2019

The intrinsic oxygen-vacancy defects in ZnO have prevented the preparation of p-type ZnO with high carrier concentration. Therefore, in this work, the effect of the concentration of H₂O₂ (used as an oxygen source) on the oxygen-vacancy concentration in ZnO prepared by atomic layer deposition was investigated. The results indicated that the oxygen-vacancy concentration in the ZnO film decreased by the oxygen-rich growth conditions when using H₂O₂ as the oxygen precursor instead of a conventional oxygen source such as H₂O. The suppression of oxygen vacancies decreased the carrier concentration and increased the resistivity. Moreover, the growth orientation changed to the (002) plane, from the combined (100) and (002) planes, with the increase in H₂O₂ concentration. The passivation of oxygen-vacancy defects in ZnO can contribute to the preparation of p-type ZnO.

• 한국식물병리학회지
• /
• 제3권2호
• /
• pp.120-123
• /
• 1987

자연상태하에서 잎도열병 병반으로부터 포자의 량을 측정하기 위하여 4종의 포자탐집기(금의 원형, 금의 개량형, 길야의 원형, 금$\cdot$길야의 개량형)를 검토한 결과, 원골한 포자형성 및 이탈, 포자채집, 검경에 있어서 한 두가지의 결점이 발견되었다. 따라서 위의 결점을 보완할 수 있는 새로운 포자채집기를 고찰, 성능을 검토하여 상기 4종의 채집기의 결점을 보충할 수 있는 결과를 얻었으므로 금후 자연상태하에서 포자이탈량 조사에 유용할 것으로 생각된다.

• Journal of Welding and Joining
• /
• 제34권1호
• /
• pp.68-74
• /
• 2016

Adoption of narrow gap welding shall be increased for the butt joint of thick plate, because the deformation and welding cost is reduced by decrease of cross-sectional area. However, sometimes narrow gap causes defects such as lack of fusion since it has small groove angle and narrow groove width. Therefore, GMAW, GTAW and SAW process shall be adopted to narrow gap welding with small bead hight and low deposition rate. In this study, Super-TIG welding using C-type strip was applied to semi-narrow gap butt joint in order to increase the welding productivity. High deposition rate 10kg/hr was obtained by high current 600A without undercut, humping bead and other welding defects. Measuring the mean and standard deviation of the melting depth to evaluate the developed processes, the fusion line type was determined by measuring the difference between maximum and minium melting depth. Furthermore, a model on arch fusion line and linear fusion line was suggested in order to prevent LF on groove wall in narrow gap butt welding.

• 한국정보통신학회논문지
• /
• 제17권11호
• /
• pp.2486-2491
• /
• 2013

세라믹 소재 영상은 사람의 육안으로 판단하기 힘든 내부 기공이나 균열, 이물질 등의 결함들이 존재한다. 본 논문에서는 사람의 육안으로 검출하기 힘든 세라믹 소재로 이루어진 파이프 용접부에 있는 결함을 확인하기 위해 ART2 알고리즘을 이용하여 세라믹 영상에서 결함을 검출하는 방법을 제안한다. 비파괴 검사는 본질에 손상이 전혀 가지 않는 검사 방법이기 때문에 소재의 결함 검출에 대해서는 적절한 방법이다. 따라서 본 논문에서는 Ends-In Search Stretching 기법을 적용하여 명암 대비를 강조하고, 명암 대비가 강조된 영상에서 삼각형 타입의 소속 함수를 이용한 퍼지 이진화 기법을 적용한 후, 임의의 패턴 입력에 대해서도 효과적으로 특징을 분류하는 개선된ART2 알고리즘을 적용하여 결함 영역을 검출한다. 제안된 방법을 세라믹 소재 영상을 대상으로 실험한 결과, 기존의 방법보다 효율적으로 결함이 검출되는 것을 확인하였다.