• 한국군사과학기술학회지
• /
• 제12권1호
• /
• pp.106-113
• /
• 2009

This paper presents a surface acoustic wave(SAW) micro-electro-mechanical-systems(MEMS) interdigital transducer (IDT) gyroscope with 80MHz central frequency on a $128^{\circ}\;YX\;LiNbO_3$, which is consisted of a two-port SAW resonator, metallic dots and dual delay lines for the sensor and reference oscillators. Reason for using two delay line oscillators is to extract the gyroscope effect by comparing the resonant frequencies between two oscillators and to compensate the temperature effect. Based on the coupling of modes(COM) simulation, an 80MHz two ports SAW resonator and dual delay line were fabricated and characterized by the network analyzer. Obtained sensitivity was $109Hz/deg{\cdot}s^{-1}$ in the angular rate range of $0{\sim}1000deg/s$. Good Linearity and superior directivity were observed.

• 한국통신학회논문지
• /
• 제18권4호
• /
• pp.468-480
• /
• 1993

본 논문에서는 2개의 동일한 1-Port 형 공진기를 병렬로 근접배치시킨 이중모드 SAW 공진기의 설계를 위하여, 우선, 결합 모드이론에 의한 1-Port 형 공진기의 특성을 기초로 하여, 도파로 모델을 적용한 이중모드 SAW 공진기의 특성을 분석하였으며, 이를 이용해서 중심 주파수가 150.15MHz이고 대역폭이 80KHz인 2-Pole 및 4-Pole 협대역 필터를 설계.제작 하였다. 이중모드 SAW 필터를 설계변수를 달리하여 여러 번 제작.실험하여 실험치와 이론치를 비교함으로써, 제품 설계에 사용 가능한 실험적 설계 특성을 얻었으며, 이동통신기기에서 사용될 수 있는 헙대역 통과 필터를 구현하였다. DMS 공진기를 구성한 압전 기판으로는 높은 주파수에서도 온도변화에 의한 주파수 이동 및 물성의 변화가 적은 ST-cut quartz(수정)를 선택하였으며, 필터의 제작은 정확한 전극구조를 얻기 위하여 고해상도 사진 식각법과 전극의 수직식각특성이 우수한 이온반응 식각법(Reactive Ion Etching)을 적용하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.71-72
• /
• 2008

In this paper, the effect of thermal annealing on surface acoustic wave (SAW) properties of aluminum nitride (AlN) films were described. The films were fabricated on Si substrates by using Pulsed Reactive Magnetron Sputtering System. The SAW properties of $600^{\circ}C$-annealed AlN films were better than those of both $900^{\circ}C$-annealed AlN films and as-deposited ones. Their SAW velocities (Raleigh mode) and insertion losses were about 5212 m/s and 16.19 dB at $600^{\circ}C$ with the wavelength of $40{\mu}m$. The dependence of characteristics of AlN films on annealing conditions were also evaluated by using Fourier Transform-Infrared Spectroscopy (FT-IR) Spectrums and Atomic Force Microscopy (AFM).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.13-16
• /
• 2009

In this study, AlN thin films were deposited on a polycrystalline (poly) 3C-SiC buffer layer for surface acoustic wave (SAW) applications using a pulsed reactive magnetron sputtering system. AFM, XRD and FT-IR were used to analyze structural properties and preferred orientation of the AlN/3C-SiC thin film. Suitability of the film in SAW applications was investigated by comparing the SAW characteristics of an interdigital transducer (IDT)/AlN/3C-SiC structure with the IDT/AIN/Si structure at 160 MHz in the temperature range $30-150^{\circ}C$. These experimental results showed that AlN films on the poly 3C-SiC layer were highly (002) oriented. Furthermore, the film showed improved temperature stability for the SAW device, $TCF\;=\;-18\;ppm//^{\circ}C$. The change in resonance frequency according to temperature was nearly linear. The insertion loss decrease was about $0.033dB/^{\circ}C$. However, some defects existed in the film, which caused a slight reduction in SAW velocity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.273-273
• /
• 2008

This paper describes the frequency response of two-port surface acoustic wave (SAW) resonator made of 002-polycrystalline aluminum nitride (AlN) thin film on 111-poly 3C-SiC buffer layer. In there, Polycrystalline AlN thin films were deposited on polycrystalline 3C-SiC buffer layer by pulsed reactive magnetron sputtering system, the polycrystalline 3C-SiC was grown on $SiO_2$/Si sample by CVD. The obtained results such as the temperature coefficient of frequency (TCF) of the device is about from 15.9 to 18.5 ppm/$^{\circ}C$, the change in resonance frequency is approximately linear (30-$150^{\circ}C$), which resonance frequency of AlN/3C-SiC structure has high temperature stability. The characteristics of AlN thin films grown on 3C-SiC buffer layer are also evaluated by using the XRD, and AFM images.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.235-235
• /
• 2009

This paper describes the influence of a polycrystalline (poly) 3C-SiC buffer layer on the surface acoustic wave (SAW) properties of poly aluminum nitride (AlN) thin films by comparing the center frequency, insertion loss, the electromechanical coupling coefficient ($k^2$), andthetemperaturecoefficientoffrequency(TCF) of an IDT/AlN/3C-SiC structure with those of an IDT/AlN/Si structure, The poly-AlN thin films with an (0002)-preferred orientation were deposited on a silicon (Si) substrate using a pulsed reactive magnetron sputtering system. Results show that the insertion loss (21.92 dB) and TCF (-18 ppm/$^{\circ}C$) of the IDT/AlN/3C-SiC structure were improved by a closely matched coefficient of thermal expansion (CTE) and small lattice mismatch (1 %) between the AlN and 3C-SiC. However, a drawback is that the $k^2(0.79%)$ and SAW velocity(5020m/s) of the AlN/3C-SiC SAW device were reduced by appearing in some non-(0002)AlN planes such as the (10 $\bar{1}$ 2) and (10 $\bar{1}$ 3) AlN planes in the AlN/SiC film. Although disadvantages were shown to exist, the use of the AlN/3C-SiC structure for SAW applications at high temperatures is possible. The characteristics of the AlN thin films were also evaluated using FT-IR spectra, XRD, and AFM images.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.112-112
• /
• 2009

In this study, the effect of a long post-deposition thermal annealing(600 and 1000 $^{\circ}C$) on the surface acoustic wave (SAW) properties of polycrystalline (poly) aluminum-nitride (AlN) thin films grown on a 3C-SiC buffer layer was investigates. The poly-AlN thin films with a (0002) preferred orientation were deposited on the substrates by using a pulsed reactive magnetron sputtering system. Experimental results show that the texture degree of AlN thin film was reduced along the increase in annealing temperature, which caused the decrease in the electromechanical coupling coefficient ($k^2$). The SAW velocity also was decreased slightly by the increase in root mean square (RMS) roughness over annealing temperature. However, the residual stress in films almost was not affect by thermal annealing process due to small lattice mismatch different and similar coefficient temperature expansion (CTE) between AlN and 3C-SiC. After the AlN film annealed at 1000 $^{\circ}C$, the insertion loss of an $IDT/AlN/3C-SiC/SiO_2/Si$ structure (-16.44 dB) was reduced by 8.79 dB in comparison with that of the as-deposited film (-25.23 dB). The improvement in the insertion loss of the film was fined according to the decrease in the grain size. The characteristics of AlN thin films were also evaluated using Fourier transform-infrared spectroscopy (FT-IR) spectra and X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) images.