• 한국농공학회논문집
• /
• 제46권4호
• /
• pp.3-11
• /
• 2004

A finite volume model is developed to simulate the surface irrigation at a paddy field. The model's capabilities are validated through comparison with the simulafed results and the observed data obtained by various experimental tests, and the simulated results are in good agreement with the observed pending depth. The result of surface irrigation simulation shows that the longer the paddy field's the length of long-sided becomes, the longer the advance and storage time is taken. To analyze surface irrigation performance with variable inflow rate, three patterns of flow variation-constant rate, initially high then low, and initially low then high-were studied. The results show that at the pattern with initially high followed by low during the latter half of the irrigation the advance time is shortest, but the pending depth of irrigation completion and irrigation effiency are the little difference between irrigation patterns.

• Coupled systems mechanics
• /
• 제7권1호
• /
• pp.95-109
• /
• 2018

The relevance of turbulent mixing in estuarine numerical models for stratified two-layer shallow water flows is analysed in this paper. A one-dimensional numerical model was developed for this purpose by extending an immiscible two-layer model with an additional source term, which accounts for turbulent mixing effects, namely the entrainment of fluid from the lower to the upper layer. The entrainment rate is quantified by an empirical equation as a function of the bulk Richardson number. A finite volume method based on an approximated Roe solver was used to solve the governing coupled system of partial differential equations. A comparison of numerical results with and without entrainment is presented to illustrate the influence of entrainment on both the salt-water intrusion length and lower layer dynamics. Furthermore, one example is given to demonstrate how entrainment terms may help to stabilize the numerical scheme and prevent a possible loss of hyperbolicity. Finally, the model with entrainment is validated by comparing the numerical results to field measurements.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.390-395
• /
• 2001

Cooling characteristics using convection and conduction heat transfer in a parallel channel with extruding heat sources are studied numerically. A two-dimensional model has been developed for numerical prediction of transient, compressible, viscous, laminar flow, and conjugate heat transfer between parallel plates with uniform block heat sources. The finite volume method is used to solve this problem. The considered assembly consists of two channels formed by two covers and one PCB which has three uniform heat source blocks. Five different cooling methods are considered to find efficient cooling method in a given geometry and heat source. The velocity and temperature fields, local temperature distribution along surface of blocks, and the maximum temperature in each block are obtained.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 추계 학술대회논문집
• /
• pp.243-248
• /
• 2007

A three-dimensional (3D) unstructured hydrodynamic solver for transient two-phase flows has been developed. A two-fluid three-field model was adopted for the two-phase flows. The three fields represent a continuous liquid, an entrained liquid, and a vapour field. The hydrodynamic solver is for the 3D component of a nuclear system code and the component-scale analysis tools for transient two-phase flows. The finite volume method and unstructured grid are adopted, which are useful for the flows in a complicated geometry. The semi-implicit ICE (Implicit Continuous-fluid Eulerian) numerical scheme has been adapted to the unstructured non-staggered grid. This paper presents the numerical method and the preliminary results of the calculations. The results show that the numerical scheme is robust and predicts the phase change and the flow transitions due to boiling and flashing problems well.

• 대한기계학회논문집B
• /
• 제24권10호
• /
• pp.1335-1342
• /
• 2000

Three-dimensional flow analysis and numerical optimization methods are presented for the design of an axial-flow fan. Steady, incompressible, three-dimensional Reynolds-averaged Navier-Stokes equations are used as governing equations, and standard k- ${\varepsilon}$ turbulence model is chosen as a turbulence model. Governing equations are discretized using finite volume method. Steepest descent method, conjugate gradient method and BFGS method are compared to determine the searching directions. Golden section method and quadratic fit-sectioning method are tested for one dimensional search. Objective function is defined as a ratio of generation rate of the turbulent kinetic energy to pressure head. Two variables concerning sweep angle distribution are selected as the design variables. Performance of the final fan designed by the optimization was tested experimentally.

• 한국전산유체공학회지
• /
• 제15권4호
• /
• pp.53-59
• /
• 2010

Preliminary design of a ground plate, a device installed close to the aircraft model for wind tunnel test to simulate the ground effect, was performed by a numerical simulation. A two-dimensional numerical study was performed initially to decide the optimal leading edge and flap configurations. Then, three-dimensional studies were conducted to decide the optimal flap deflection angle for pressure distribution reduction since the plate and the plate supporting system generate static pressure difference between the upper and lower flow regions. Three-dimensional simulation additionally studied the effect of the clearance between the plate and the wind tunnel side wall. For the efficiency of computation, half model was simulated and a symmetric boundary condition was applied on the center plane. Based on the preliminary design, a ground plate was designed, manufactured and tested at the Korea Aerospace Research Institute(KARI) wind tunnel. The measured pressure differences versus flap deflection angle agreed well with the predicted results.

• Journal of Mechanical Science and Technology
• /
• 제17권7호
• /
• pp.1073-1082
• /
• 2003

Many researchers have investigated the blood flow characteristics through bileaflet mechanical heart valves using computational fluid dynamics (CFD) models. Their numerical approach methods can be classified into three types; steady flow analysis, pulsatile flow analysis with fixed leaflets, and pulsatile flow analysis with moving leaflets. The first and second methods have been generally employed for two-dimensional and three-dimensional calculations. The pulsatile flow analysis interacted with moving leaflets has been recently introduced and tried only in two-dimensional analysis because this approach method has difficulty in considering simultaneously two physics of blood flow and leaflet behavior interacted with blood flow. In this publication, numerical calculation for pulsatile flow with moving leaflets using a fluid-structure interaction method has been performed in a three-dimensional geometry. Also, pulsatile flow with fixed leaflets has been analyzed for comparison with the case with moving leaflets. The calculated results using the fluid-structure interaction model have shown good agreements with results visualized by previous experiments. In peak systole. calculations with the two approach methods have predicted similar flow fields. However, the model with fixed leaflets has not been able to predict the flow fields during opening and closing phases. Therefore, the model with moving leaflets is rigorously required for advanced analysis of flow fields.

• 대한수학회논문집
• /
• 제22권3호
• /
• pp.453-464
• /
• 2007

A computationally efficient numerical scheme is presented for the phase-field model of two-phase systems for anisotropic interfacial energy. The scheme is solved by using a nonlinear multigrid method. When the coefficient for the anisotropic interfacial energy is sufficiently high, the interface of the system shows corners or missing crystallographic orientations. Numerical simulations with high and low anisotropic coefficients show excellent agreement with exact equilibrium shapes. We also present spinodal decomposition, which shows the robustness of the pro-posed scheme.

• Ecology and Resilient Infrastructure
• /
• 제3권4호
• /
• pp.307-314
• /
• 2016

최근 하천복원 사업은 과거 인공적인 부분을 개선하는 범위를 벗어나 격리차단된 구하도까지 복원하는 수준에 이르렀다. 구하도 복원은 하천 제방과 같은 종적 구조물에 의해 차단된 공간의 수리적 연결성 회복이 중요하다. 그러나 하천복원이 적절히 수행되었는지 관한 평가방법이 부족한 상황이기에 본 연구에서는 대상하천에서의 생태적 연결성 평가를 위한 수단을 제공하고자 한다. 이 연구에서 강우에 의한 유역유출 및 하도흐름 해석이 동시에 가능한 1차원 수치모형을 개발하여 청미천 유역에 적용한 바 있다. 특히 이 연구에서 1차원의 홍수추적 결과를 2차원의 공간분포로 변환시키고 시간에 따른 2차원의 수리특성으로부터 서식처적합도까지 산출하여 연결성 회복정도를 평가하는 수치모형을 개발하였으며, 이를 청미천 구하도 복원지역에 적용하였다. 복잡할 뿐만아니라 시간도 많이 소요되는 2차원의 분석을 수행하지 않고서도 1차원 수리특성 결과를 확장해서 2차원 수리특성을 쉽게 구할 수 있도록 한 것이 본 연구의 특징이다. 본 연구의 결과를 이용하면 구간별 대상종별 서식처적합도를 용이하게 산정할 수 있다.

• 한국산학기술학회논문지
• /
• 제15권9호
• /
• pp.5801-5812
• /
• 2014

강변저류지는 일정 규모 이상의 홍수를 하도로부터 분배하여 홍수량을 저감시킴으로써 홍수위험을 저감시키는 수공 구조물이다. 본 연구에서는 강변저류지에 의한 홍수저감효과를 분석하기 위하여 수치모의를 수행하였다. 기후변화에 의한 이상홍수 발생시, 홍수저감효과를 분석하기 위하여 계획빈도를 상회하는 수문조건에 대한 검토를 수행하여 강변저류지의 홍수조절능력을 분석하였다. 또한, 강변저류지가 설치된 하천은 복잡한 지형과 횡월류위어를 통하여 강변저류지로 분배되는 흐름이 동시에 발생하므로 복잡한 흐름현상을 구현하기 위하여 2차원 모형의 적용성을 검토하였다. 기존 강변저류지 홍수저감효과 분석시 주로 활용되는 1차원 모형과 2차원 모형의 결과를 비교 및 검토하였다. 본 연구결과 강변저류지에 의한 홍수저감효과를 모의하기 위해서는 지형 및 횡월류 흐름을 공간적으로 구현할 수 있는 2차원 모형을 활용하는 것이 합리적인 것으로 판단된다.