• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.2 s.25
• /
• pp.65-71
• /
• 2007

In this research, we made a one and two-dimensional analysis of numerical data collected from the bend curvature of a bended river section. According to the result from the numerical analysis, the inflow & output angle caused a water level deviation which increased with an increase of the flood discharge. From the water level deviation of our two-dimensional numerical model, we obtained the maximum slope of 6,67% when the inflow and output angle was 105 degrees and the flood discharge was 500 CMS. As for the right side, the differences with the one-dimensional numerical model were reduced when the angle was more than $90^{\circ}$. As for the left side the differences were reduced when the angle was more than $105^{\circ}$. For a river with more than 90 degrees bend curvature, a hydraulic experiment would be more appropriate than a numerical analysis.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.14 no.4
• /
• pp.41-54
• /
• 2011

Tree roots can enhance soil shear strength and slope stability. However, there has been a limited study about root reinforcement of major tree species in Korea because of some experimental difficulties. Thus, this study was conducted to analyze the performance of Japanese larch (Larix kaempferi) and Korean pine (Pinus koraiensis) which are two common plantation species in Korea. Profile wall method was used to measure the spatial distribution of root system and its diameter within 15 soil walls of Japanese larch stand and 13 soil walls of Korean pine stand in Taehwa University Forest, Seoul National University, Korea. Root tensile properties of each species were assessed in the laboratory, and root reinforcements were estimated by Wu model. The study observed that the number and cross-sectional area (CSA) of root in both species could tend to decrease with soil depth. Especially, CSA were well-fitted to exponential functions of soil depth. Mean root area ratios (RAR) were 0.03% and 0.10% for Japanese larch and Korean pine, respectively. Estimated root reinforcement from Wu model were, on the average, 4.04 kPa for Japanese larch and 12.26 kPa for Korean pine. Overall, it was concluded that root reinforcement increased the factor of safety (Fs) of slope for small-scale landslide as the result of two-dimensional (2-D) infinite slope stability analysis considering vegetation effects.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.3
• /
• pp.340-349
• /
• 2016

A coupled room system consists of adjacent rooms and apertures where the sound energy is exchanged between the two rooms. Acoustically, a coupled room system shows a non-exponential decay profile. Most of the related researches have been to analyze the acoustic properties of two-room coupled system so far whereas three-room coupled system were seldom studied. In this regard, this paper aims to analyse the distribution of sound pressure level, sound decay curve of three-room coupled system and sound energy flow between them by using the acoustic diffusion model and to further verify them through experiments. Firstly, the sound pressure level distribution and mean sound pressure level in the steady-state condition are analyzed at various frequencies and source locations. Good agreements are observed in both experiments and analysis results. Secondly, two double slope effect quantifiers of sound attenuation, LDT/EDT and LDT/T10 are compared at various frequencies and for different source locations. The result indicates that LDT/T10, less affected by the early reflection patterns than LDT/EDT, is more suitable to the analysis and experiments of a multi-slope sound decay curve. Lastly, the sound energy flow in each room is analyzed based on the acoustic diffusion model. After the early decay stage, the sound energy is observed to flow from the room with a long reverberation time to the room with a short one.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.1
• /
• pp.20-24
• /
• 2008

A bid-based pool(BBP) model is representative of energy market structure in a number of restructured electricity markets. Supply function equilibrium(SFE) models of interaction better match what is explicitly required in the bid formats of typical BBP markets. Many of the results in the SFE literature involve restrictive parametrization of the bid cost functions. In the SFE models, two parameters, intercept and slope, are available for strategic bidding. This paper addresses the realistic competition format that players can choose both parameters arbitrarily. In a fixed demand function, equilibrium conditions for generation company's profit maximization have a degree of freedom, which induces multi-equilibrium. So it is hard to choose a convergent equilibrium. However, consideration of stochastic demand function makes the equilibrium conditions independent each other based on the amount of variance of stochastic demand function. This variance provides the bidding players with incentives to change the slope parameter from an equilibrium for a fixed demand function until the slope parameter equilibrium.

• Journal of Biosystems Engineering
• /
• v.2 no.1
• /
• pp.33-48
• /
• 1977

Transporting agricultural products and the other material by the two-wheel-tractor (power-tiler)and trailer system may be one of its most widely used farming functions.The safety and hitching load for all the previaling performing conditions may be the general concern over the operation of the tiller-trailer system. In this study, a mathematical model to determine the static and dynamic forces excerting on the hitch point were developed . Based on the analysis of the model and the field measurements. the limiting hitching load and critical slope were analyzed. The results of the study are summarized as follows ; 1) The limit angle of slope land for the safety steering that two-wheel tractor-single axle trailer system was able to transport agricultural products was the direct angle (${\gamma}$) = 8 ; the cross angle$\beta$) 15 ; and it was decreased in accordance with the increase of carrying load ($W_4). 2) The critical velocity for safe operation in case of running on downward hill road was about 1.08m/sec. 3) The limiting carrying load for the safe steering was W$_4$=600kg. The degree of the safe steering for different braking methods was given in order as follows ; Simulataneous braking the tractor and trailer , braking the trailer only, and braking tractor only. 4) Among the three components of impact loads excerting on the hitch point, the component in the lateral direction ($P_{Vy}$) was near zero in spite of increase of hitching load ($W_4) , while the components in the other two mutually perpedicular directions ($P_{Vx}$ and ($P_{Vz}$) ) had larger values in horizontal plane than those in the slope lands. 5) Moment of forces on the lateral direction (M$y$) had the largest value among the three components of impact moment acting on the hitch point, however all the components were sharply increased in accordance with the increase of hitching loads ($W_4. Three components of the moment were the negative values.

• Smart Structures and Systems
• /
• v.31 no.5
• /
• pp.517-529
• /
• 2023

Using a device composed of two lateral pressure plates (LPPs) and a steel reinforcement bar to apply horizontal pressure on slope surfaces, a newly developed prestress-reinforced embankment (PRE) is proposed, to which can be adopted in strengthening railway subgrades. In this study, an analytical model, which is available of calculating additional confining stress (σ_H) at any point in a PRE, was established based on the theory of elasticity. In addition, to verify the proposed analytical model, three dimensional (3D) finite element analyses were conducted and the feasibility in application was also identified and discussed. In order to study the performance of the PRE, the propagation of σ_H in a PRE was analyzed and discussed based on the analytical model. For the aim of convenience in application, calculation charts were developed in terms of three dimensionless parameters, and they can be used to accurately and efficiently predict the σ_H in a PRE regardless of the embankment slope ratio and LPP side length ratio. Finally, the potential applications of the proposed analytical model were discussed.

• Phonetics and Speech Sciences
• /
• v.3 no.1
• /
• pp.145-151
• /
• 2011

In view of the hypothesis that the effects of Parkinson's disease on voice production can be detected before pharmacological intervention, the prosodic features of patients with idiopathic Parkinson's disease (IPD) and a healthy aging group were diagnostically analyzed with the long term object of establishing, for clinical purposes, early disease-progression biomarkers. Twenty patients (male 8; female 12) with IPD (prior to pharmacological intervention) and a healthy control group of 22 (male 10; female 12) were selected. Ten sentences were recorded with a head-worn microphone. One sentence was chosen for the analysis of this paper. Relevant parameters, i.e. 3-dimensional model (F0, intensity, duration) and pitch and intensity related slopes (maxEnergy, maxF0, meanAbS, semiT, meanEnergy, meanF0), were analyzed by two-group discriminant analysis. The stepwise estimation method of discriminant analysis was performed by gender. The discriminant functions predicted 83.9% of the male test data correctly while the prediction rate was 93.1% for the female group. The results showed that meanF0_slope and semiT_slope were more important parameters than the others for the male group. For the female group, the meanEnergy_slope and maxEnergy_slope were the important ones. These findings indicate that significant parameters are different for the male and female group. Gender lifestyle may be responsible for this difference. Dysprosodic features of IPD show not simultaneously but progressively in terms of F0, intensity and duration.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.18 no.2
• /
• pp.169-177
• /
• 2000

The modelling technique on the terrain of real-world in geo-spatial information system is a primary element for geo-information processing. This paper is designed to make use of TIN in geo-spatial information system and study the development and application of high-precision 3-D spatial analysis technique applied to terrain features. According to this research, MODEL 3 applied to breakline in mild slope/steep slope and MODEL 2 applied to peak in complex region show relatively low RMSE. This consequence proves that these two models have high precision in comparison with other models. This study also finds out optimal routines in the estimation method of slope grade and in the construction method of surface. N_T, LSP_T and LSQ_T in mild slope, N_T in steep slope, and LSQ_T in complex region turn out to be the optimal routines for high-precision 3-D spatial analysis.

• Journal of Korea Water Resources Association
• /
• v.38 no.3 s.152
• /
• pp.223-233
• /
• 2005

In this study, a two-dimensional model for identifying areas of erosion and deposition over a basin was developed based on the mass balance principle in a distributed model. The program consists of three steps: (a) estimation of soil erosion; (b) determination of flow amount and direction; and (c) estimation of mass balance. Soil erosion was estimated with USLE. A single-direction (SF) and a multi-direction flow algorithm (MF) were applied to estimate slope length (L). The Maximum Downhill Slope Method (MDS) and the Neighborhood Method (NBH) were used to estimate the slope degree (S). Sediment transport resulting from eroded soil was estimated using Ferro's (1998) and Swift's (2000) sediment delivery ratio (DR). The model was validated by comparing the predicted sediment yields for three basins with measured data. The developed algorithm showed that Ferro's DR method combined with the MDS and MF produced the best agreement with the dredging records of three agricultural reservoir basins in Korea.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.35 no.2
• /
• pp.33-40
• /
• 2023

Wave overtopping rate is one of the most important design parameters for coastal structures. In this study, the physical model tests for measuring the wave overtopping have been conducted with the foreshore slope in front of the seawall. The bottom seabed for the coastal road area was fabricated at the wave flume for two areas in the East sea areas. The wave overtopping rate was measured for various water depths and wave conditions in each coastal area. In particular, the impulsive wave conditions were compared with the previous research and the similar trends of wave overtopping was observed. It could be known that the effect of foreshore slope was significant and should be concerned for applying theses formula like EurOtop.