• 대한전기학회논문지
• /
• 제36권10호
• /
• pp.713-718
• /
• 1987

A new method for the modeling of non-ideal dc-dc converters whose switching times are finite is proposed. The effects of finite turn-on, turn-off times, delay time, storage time, reverse recovery process on the system stability, dc transfer function and efficiency are investigated. It is verified how system poles are changed and how dc transfer function and efficiency are decreased by non-ideal switching.

• Journal of Power Electronics
• /
• 제19권2호
• /
• pp.353-362
• /
• 2019

To address the problem of circulating current loss in the traditional zero-current switching (ZCS) full-bridge (FB) DC/DC converter, a ZCS FB DC/DC converter topology and modulation strategy is proposed in this paper. The strategy can achieve ZCS turn on and zero-voltage and zero-current switching (ZVZCS) turn off for the primary switches and realize ZVZCS turn on and zero-voltage switching (ZVS) turn off for the auxiliary switches. Moreover, its resonant circuit power is small. Compared with the traditional phase shift full-bridge converter, the new converter decreases circulating current loss and does not increase the current stress of the primary switches and the voltage stress of the rectifier diodes. The diodes turn off naturally when the current decreases to zero. Thus, neither reverse recovery current nor loss on diodes occurs. In this paper, we analyzed the operating principle, steady-state characteristics and soft-switching conditions and range of the converter in detail. A 740 V/1 kW, 100 kHz experimental prototype was established, verifying the effectiveness of the converter through experimental results.

• 에너지공학
• /
• 제18권1호
• /
• pp.17-21
• /
• 2009

By using the heat recovery of water-cooled chillers, it is possible to reduce the energy operating costs positively and at the same time it could fulfill the heating re-heat air conditioning system as well as the hot water requirements. Basically templifiers are designed to economically to turn the waste heat into useful heat. Waste heat is extracted from a fluid stream by cooling it in the evaporator, the compressor amplifies the temperature of the heat and the condenser delivers the heat to heating loads such as space heating, kitchens and domestic hot water. Design of higher water temperature requirements and split condenser heat recovery chiller system (using of templifiers) produced hotter condenser water approximately up to $60^{\circ}C$ and control the entire heat recovery system.

• 생물환경조절학회지
• /
• 제12권3호
• /
• pp.107-113
• /
• 2003

본 연구에서는 온실의 온풍식 난방시스템 연통에 장착할 수 있는 폐열 회수기의 성능 개선을 목적으로 기 설계된 세 가지 열교환 장치와 기존의 장치에서 열교환 면적과 파이프의 두께 및 공기흐름 방향을 개량한 새 열교환 장치에 대해 열회수 성능을 실험적으로 비교 분석하였다. 그 결과 기존의 열 교환장치인 A형, B형 및 C형의 열회수 성능은 동일 송풍전입에서 각각 42.2%, 40.6% 및 54.4% 정도였으나 , 새로 개량된 D형은 69.2%로써 가장 현저히 높게 나타났다. 그러나 열회수용 공기의 흐름방향 변화에 따른 열회수 성능 개선효과 (A형 대비 B형)는 없는 것으로 나타나 적정 송풍기 용량이라면 직선형이 공기의 흐름방향 180${\circ}C$ 굴절시키는 헤어핀형보다 효과적인 것으로 판단된다. 결국 열회수 성능은 열회수 시스템의 열교환 면적과 열교환 파이프의 두께 및 풍속에 크게 좌우되는 것으로 나타났다. 따라서, 열교환 파이프의 내구성 등 을 고려하여 기능한 한 범위 내에서 열 교환면적을 증대시키거나 열교환 파이프의 두께를 앓게 하고 풍속을 증대시키는 것이 열회수 성능 개선효과와 직결됨을 알 수 있었다. 그리고 송풍기 용량이 필요이상으로 큰 경우, 소비전력이 많게 되는 등의 문제가 있기 때문에 적정용량 및 제품의 안정성을 고려하여 선택해야 할 것으로 판단되었다.

• 한국복식학회:학술대회논문집
• /
• 한국복식학회 2001년도 19th International Costume Association Congress
• /
• pp.50-52
• /
• 2001

The main purpose of this study is to research ways for waste reduction in manufacturing, materials regeneration and clean production in apparel manufacturing in Taiwan, in order to achieve 3E: Efficiency, Economy and Environmental Protection. Specifically, this study hopes to address the following three areas: (1) To study the processing technologies which can turn apparel wastes to resources (2) To increase the efficiency in the use of energy and resources in apparel production (3) To establish a system for improving the recovery from unwanted apparel in Taiwan, in order to improve environmental protection and to reduce pollution.

• Journal of Power Electronics
• /
• 제6권3호
• /
• pp.253-263
• /
• 2006

A high performance and low cost single switch current fed energy recovery circuit (ERC) for an alternating current (AC) plasma display panel (PDP) is proposed. Since it is composed of only one power switch compared with the conventional circuit consisting of four power switches and two large energy recovery capacitors, the ERC features a simpler structure and lower cost. Furthermore, since all power switches can be switched under soft switching operating conditions, the proposed circuit has desirable merits such as increased reliability and low switching loss. Specifically, there are no serious voltage notches across the PDP with the aid of gas discharge current compensation, which can greatly reduce the current stress of all inverter switches, and provide those switches with the turn on timing margin. To confirm the validity of proposed circuit, its operation and performance were verified on a prototype for 7-inch test PDP.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.806-808
• /
• 1993

New soft recovery drive which can alleviate the loss due to reverse recovery of diode is proposed. By using this drive, the reverse current of the diode is minimized and stabilized because there is inner local feedback loop between the turn-on current of the power MOSFET and the reverse recovery current of the diode. The loss and EMI noise can be considerably reduced in this way. Brief operational principle and experimental results are included to verify the usefulness.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.113-116
• /
• 2003

Hem quality can be determined mainly by turn-down and roll-in. Turn-down, that is created by the elastic recovery, can't be easily detected and measured since it is usually as small as 0.03 m. This study is focused on the precise evaluation of the hemming defects through analytical and experimetal approaches, and on the investigation of the influence of process parameters on the final hem quality. Implicit finite element analysis of plane-strain hemming process is performed by using a commercial code ABAQUS/Standard. Experiment and measurement is also carried out for steel and aluminium sheet metals, and the results are compared with those of analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1226-1228
• /
• 2004

A novel lossless passive snubber is proposed for soft switching the boost type converters. The proposed snubber does not use any auxiliary switches. but uses two identical snubber capacitors which are charged in parallel at turn off of the main switch and discharged in series at turn on automatically, and the discharged energy is recovered effectively (more than $95[\%]$ recovery) into the output capacitor. Thus, the snubber provides zero voltage switching for the converter main switch, reducing both the turn off losses and the electromagnetic interference(EMI) noise, whitch improves the converter performance. The experimental results of a 20[kHz] 600[W] DC-DC boost converter and a single-phase AC-DC boost rectifier with the new snubber are presented.

• Journal of Electrical Engineering and Technology
• /
• 제9권2호
• /
• pp.501-507
• /
• 2014

This paper describes the improvement in converter efficiency by reducing the switching loss and by recovering the snubber stored energy. A capacitive based passive regenerative snubber circuit is modeled for a dc-dc boost converter. The proposed snubber is mainly used to reduce the turn-off loss of the main switch. The energy recovery process and the turn-off loss depends on the size of the snubber capacitance; therefore, the conventional and the proposed converters are designed for high and low input voltage conditions with different sizes of the snubber capacitance. Based on the results obtained, the snubber capacitors are classified as small, normal and large snubbers. The Matlab simulation results obtained are presented.