• Journal of Energy Engineering
• /
• v.11 no.1
• /
• pp.10-17
• /
• 2002

The objective of performing this study is to develop low emission condensing gas boiler. To reduce NOx and CO, three reasonable distances between burner and heat exchanger were decided through the experiments of model plane burner. Three burners with different diameter were made and then emission characteristics were examined. The optimum burner geometry was determined from flame stability, pollutant emission characteristics and applicability to the practical boiler system. In the domain of equivalence ratio 0.68~0.85, turn-down ratio of the burner designed by this research was extended to a wider range of 5 : 1. Thermal efficiency of the boiler developed by this study reached to 97% (LHV basis) of heating water efficiency at heating load of 20,000 kcal/hr when fueled by both of LNG or LPG. Emission ($O_2$=0%, wet basis) of NOx and CO concentration was 26 ppm and 85 ppm when fueled by LNG, 41 ppm and 113 ppm when fueled by LPG respectively.

• International Journal of Highway Engineering
• /
• v.18 no.4
• /
• pp.83-92
• /
• 2016

PURPOSES : The purpose of this study was to develop safety performance functions (SPFs) that use zero-inflated negative binomial regression models for urban intersections in central business districts (CBDs), and to compare the statistical significance of developed models against that of regular negative binomial regression models. METHODS : To develop and analyze the SPFs of intersections in CBDs, data acquisition was conducted for dependent and independent variables in areas of study. We analyzed the SPFs using zero-inflated negative binomial regression model as well as regular negative binomial regression model. We then compared the results by analyzing the statistical significance of the models. RESULTS : SPFs were estimated for all accidents and injury accidents at intersections in CBDs in terms of variables such as AADT, Number of Lanes at Major Roads, Median Barriers, Right Turn with an Exclusive Turn Lane, Turning Guideline, and Front Signal. We also estimated the log-likelihood at convergence and the likelihood ratio of SPFs for comparing the zero-inflated model with the regular model. In he SPFs, estimated log-likelihood at convergence and the likelihood ratio of the zero-inflated model were at -836.736, 0.193 and -836.415, 0.195. Also estimated the log-likelihood at convergence and likelihood ratio of the regular model were at -843.547, 0.187 and -842.631, 0.189, respectively. These figures demonstrate that zero-inflated negative binomial regression models can better explain traffic accidents at intersections in CBDs. CONCLUSIONS : SPFs that use a zero-inflated negative binomial regression model demonstrate better statistical significance compared with those that use a regular negative binomial regression model.

• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.199-211
• /
• 2008

This study deals with the side right-angle collisions of 4-legged signalized intersections in Cheongju. The goals are to analyze the characteristics of accidents and to find out the accident factors that affect severity using ordered probit model. In pursuing the above, the study uses the data of 580 side right-angle collisions occurred at the 181 intersections(2004-2005). The analyses show that more accidents were occurred in the nighttime and in going straight. The main cause was analyzed to be the red-light violation. Also, the main results of modeling are the following, First, the likelihood ratio index is 0.094 and t-ratio values that explain goodness of fit are significant. Second, minor road traffic volumes, minor road lanes, major road left-turn lanes, major road left-turn signal, major road yellow signal time, cross angle, major and minor road speed limits are significant factors affecting crash severities at signalized intersections.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.43-53
• /
• 2007

We have analyzed low current operation characteristics of a VCSEL transmitter operating at fixed Current over wide temperature range. Used 850 nm oxide VCSEL has low temperature dependence of the threshold current and $d^2I_{th}/dT^2$ is approximately $1.346\times10^{-4}mA/^{\circ}C^2$. We fixed on-current so that output power from the chip is 1 mW at $20^{\circ}C$ and investigated the turn-on, turn-off characteristics and eye-diagram of the 850 nm oxide VCSEL transmitter with varying ambient temperature and off-current. We measured rise time, fall time, extinction ratio and timing jitter by changing tile ambient temperature and off-current. With the fixed off-current of around $0.1\sim0.2mA$ lower than the lowest threshold current the transmitter successfully operated at 1.25 Gbps over a wide temperature range from $-20^{\circ}C$ to $80^{\circ}C$.

• ETRI Journal
• /
• v.37 no.1
• /
• pp.26-31
• /
• 2015

Axial-ratio (AR) bandwidth enhancement is achieved for a circularly polarized (CP) cylindrical dielectric resonator antenna (DRA) using a wideband hybrid coupler (WHC) combined with dual probe feed. The presented WHC, comprised of a Wilkinson power divider and a wideband $90^{\circ}$ shifter, delivers good characteristics in terms of 3 dB power splitting and consistent $90^{\circ}$ (${\pm}5^{\circ}$) phase shifting over a wide bandwidth. In turn, the proposed CP DRA, for the employment of the WHC, in place of conventional designs, provides a significant enhancement on AR bandwidth and impedance matching. The antenna prototype with the WHC exhibits a 3 dB AR bandwidth of 48.66%, an impedance bandwidth of 52.5% for voltage standing wave ratio (VSWR) ${\leq}2$, and a bandwidth of 44.66% for a gain of no less than 3 dBi. Experiments demonstrate that the proposed WHC is suitable for broadband CP DRA design.

• Journal of Power Electronics
• /
• v.17 no.2
• /
• pp.315-322
• /
• 2017

LED is a promising new generation of green lighting with the advantages of high efficiency, good optical performance, long lifetime and environmental friendliness. A pulsating current can be used to drive LEDs. However, current with a high peak-to-average ratio is unfavorable for LEDs. A novel control scheme for the ac-dc critical conduction mode (CRM) flyback LED driver is proposed in this paper. By using the input voltage, output voltage and average output current to control the turn-on time of the switch, the peak-to-average ratio of the output current can be reduced. The operation principle is analyzed and an implementation circuit is put forward. Experimental results show the effectiveness of the proposed scheme.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.436-439
• /
• 2007

This paper describes the optimization of PGS(Patterned Ground Shield) of 5.5 turns rectangular spiral inductor using Taguchi's method. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. By using the taguchi's method, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.977-979
• /
• 2001

The application of SRM(Switched Reluctance Motor) is dramatically increasing due to a simple mechanical structure, high efficiency and a good high speed characteristics. Generally, turn-off angle of power switch must be limited the demagnetization period. To control high conduction ratio in motor operation and regenerative voltage in the generator operation in the SRM, multi-level voltage control is effective. This paper proposes multi-level inverter to have a maximum conduction ratio of SRM. The proposed method is verified by experiment.

• Journal of electromagnetic engineering and science
• /
• v.13 no.3
• /
• pp.165-172
• /
• 2013

This paper describes a design for a spiral antenna with a conical wall to obtain the high gain. The gain and the axial ratio of the spiral antenna were improved by a new design that included a conical wall and an optimized Archimedean slit on the ground plane in a conventional antenna with a circular cavity wall and a 4.5-turn slit. A gain improvement of 9.5 dBi higher and a good axial ratio of 1.9 dB lower were measured by the added conical wall and the newly designed slit from the current distribution control on the ground plane, respectively. The measured return loss, gain and axial ratio of the proposed antenna showed a good agreement with the simulated results. The proposed antenna will be applied to a non-linear junction detector system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.198-201
• /
• 1997

Aluminum alloy sheets are considered as one of the high potential substitutes for steel sheets considering weight reduction of automobiles. However, aluminum alloy sheets have drawbacks in higher prices and inferior formability compared to steel sheets. In order to achieve good deep drawability, it is imperative to obtain well developed {111} texture which gives rise to higher plastic strain ratio. It is difficult to obtain this texture from conventional rolling and annealing processes. Therefore, an unconventional rolling process which enhances shear deformation has been experimentally studied to obtain the well developed {111} texture, which in turn gives rise to a substantial increase in plastic strain ratio.