• Journal of the Korean Ceramic Society
• /
• v.43 no.8 s.291
• /
• pp.498-503
• /
• 2006

A gas turbine blade with thermal barrier ceramic coating is operated at high temperature to increase engine efficiency. Recently, thermal barrier characteristics have been improved by advanced coating technology through microstructure control and increase of adhesion force of the coating layer. More advanced coating materials, rare earth zircon ate ceramics have been studied for replacing YSZ coatings as thermal barrier coatings. In this study, $La_2O_3,\;HfO_2,\;CeO_2,\;Gd_2O_3$ and pure or yttria stabilized zirconia were prepared. Microstructure analysis and the evaluation of mechanical properties such as Hertzian indentation and hardness test were performed.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.713-716
• /
• 1998

To examine the influence of unsteady wake on the flow and heat transfer characteristics, an experiment has been conducted in a four-vane linear cascade. Flow and heat transfer measurements are made for the inlet Reynolds number of 66000(based on chord length and free-stream velocity). Turbulent intensity and stress were measured using hot wire anemometer, and to measure the convective heat transfer coefficients on the blade surfaces liquid crystal/gold film Intrex technique was used. The disturbance by the unsteady wake is characterized by the unresolved unsteadiness. The unsteady wake enhances the turbulent motion of flow in the cascade passage. It also promotes the boundary layer development and transition. The results show that heat transfer coefficients on the suction surface increase with increasing unresolved unsteadiness.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.886-895
• /
• 2009

The purpose of this work is to compare and analyze computed results with experimental data of NREL (National Renewable Energy Laboratory) Phase VI for the whole operating conditions of various wind speeds using $\kappa-\omega$ turbulence model provided in the commercial code, FLUENT. Performance results such as power coefficient, shaft torque, pressure coefficient show a good agreement with experimental data. But, root bending moment is over-predicted than the experimentally measured value by about 30% for the whole operating conditions because of indefinite measurement reference. Nevertheless, these results qualitatively show a good tendency in the aspect of aerodynamic performance. As wind speed increases, streamlines on the surface of blade show more and more complex pattern.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1436-1441
• /
• 2004

The internal cooling passage of a gas turbine blade can be modeled as a ribbed channel. Most studies have considered square ribs. However, the ribs can be rounded due to improper manufacturing or wear during the operation. Hence, we have studied two different rib geometries in this study, i.e. square and semicircle ribs. We have performed large eddy simulations (LES) and experiments to validate the results from the simulations. LES predicts the detailed flow and thermal features, which have not been captured by simulations using turbulence models. By investigating the instantaneous flow and thermal fields, we propose the mechanisms for the local heat transfer distribution between ribs. For both the geometries, heat transfer is enhanced by the entrainment of the cold fluid by the vortical motions and impingement of the entrained cold fluid on the ribs.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.336-341
• /
• 2004

This research investigates the feasibility of ultrasonic microscope for nondestructive assessment of thermal degradation in artificially aged commercial Co-base superalloy, FSX414. This alloy has been used for high temperature structure applications such as stationary gas turbine blade and nozzle chamber in fossil plant. Microstructural change was found that the fine carbides became coarser and spheroidized in matrix as aging time increased. The leaky surface acoustic wave velocity gradually decreases by a maximum of 4.7% with increasing aging time up to 4,000hours. However, the longitudinal wave velocity has a little change. Also, it has a good correlation between leaky surface acoustic wave velocity and Vickers hardness. Consequently, LSAW can be used to examine the degree of degradation in thermally aged Co-base superalloy.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.256-262
• /
• 1999

By development of heat resistant alloy, there are much improvement of gas turbine engines. But heat resistant alloy has difficulty of machining. therefore, ECM (Electrochemical Machining) is used for Machining of 3 dimensional curved surface of Ni-base alloy. The purpose of this paper is to investigate ECM parameters that make tile good surface for Ni-base alloy blade. For this purpose, we have been investigated that center line average surface roughness(R$\sub$a/), average R$\sub$a/, Maximum R$\sub$a/ and Standard deviation of R$\sub$a/ for measuring positions is influenced on ECM parameters such as electrolyte types, dwell time, electrolyte pressure and sort of electrolyte for Inconel 718 and Waspaloy.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.11a
• /
• pp.22-22
• /
• 1997

무공해 에너지원은 화석에너지의 고갈과 환경오염의 심각한 문제로 인하여 절실히 요구되고 있는 실정이다. 그중 풍력발전 시스템은 타 에너지원에 비해 여러 가지 측면에서 유리한 점을 가치고 있다. 본 연구에서는 500Kw급 풍력발전 시스템을 개발함에 있어, 적합한 공력 성능 및 구조성능을 가지는 회전날개 설계과정을 수행하였다. 공력설계는 운용지역의 풍황을 고려하여 회전날개의 외형을 결정하였고 이를 바탕으로 공력성능해석이 수행되었으며, 구조설계는 복합재료를 사용하여 쉘-스파 구조를 갖도록 설계하여 굽힘 및 비틀림 그리고 피로수명에 대한 구조해석이 수행되었다. 그 결과 4m/s의 미풍에서도 운용가능하며, 12m/s에서는 정격출력 550Kw를 생산할 수 있는 형상이 설계되었고, 또한 20년 이상의 피로수명이 확보되었으며, 공질 등의 동적인 문제도 발생하지 않음을 확인하였다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.64-67
• /
• 2010

본 논문에서는 풍력 발전기에 사용되는 블레이드의 동특성을 해석하기 위한 프로그램을 개발하였다. 복잡한 형상의 풍력 발전기 블레이드의 모델을 단순화시키기 위하여 보 이론을 이용하였다. 블레이드의 회전 운동은 Hamilton 원리를 유한요소 보 모델을 이용하여 정식화를 수행하였다. 회전 속도에 따라 블레이드에 적용되는 원심력과 검증된 단면 물성치를 이용하여 복합재료 블레이드의 고유치 해석을 수행하였다. 기존의 상용 소프트웨어의 해석 결과와 비교를 통하여 검증 연구를 수행하였으며, 이를 토대로 본 해석 프로그램의 타당성을 보였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.4
• /
• pp.56-62
• /
• 2008

This study presents the aerodynamic design and numerical analysis results on a transonic centrifugal compressor which is used for gas turbine systems. Mean-line analysis and quasi-3D analysis are used for the aerodynamic design, and Reynolds-averaged Navier-Stokes analysis is applied to flow analysis of the compressor. The aerodynamic parameters for a transonic compressor, such as pressure coefficient, swirl parameter, blade loading, are discussed, and flow characteristics in the impeller and diffuser are discussed.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.346-348
• /
• 2001

In this paper a wind power simulator is designed and implemented. This simulator realize the torque of wind blade by DC motor. And squirrel-cage induction machine is used as generator and controlled to achieve the maximum power point tracking(MPPT) algorithm.