• 대한기계학회논문집B
• /
• 제29권4호
• /
• pp.485-494
• /
• 2005

For the extensive investigation of local heat/mass transfer on the near-tip surface of turbine blade, experiments were conducted in a low speed stationary annular cascade. The turbine test section has a single stage composed of sixteen guide vanes and blades. The chord length and the height of the tested blade are 150 mm and about 125 mm, respectively. The blade has flat tip geometry and the mean tip clearance is about $2.5{\%}$ of the blade chord. Detailed mass transfer coefficient on the blade near-tip surface was obtained using a naphthalene sublimation technique. The inlet flow Reynolds number based on chord length and incoming flow velocity is changed from $1.0{\times}10^{5}\;to\;2.3{\times}10^{5}.$ Extremely complex heat transfer characteristics are observed on the blade surface due, to complicated flow patterns, such as flow acceleration, laminarization, transition, separation bubble and tip leakage flow. Especially, the suction side surface of the blade has higher heat/mass transfer coefficients and more complex distribution than the pressure side surface, which is related to the leakage flow. For all the tested Reynolds numbers, the heat/mass transfer characteristics on the turbine blade are the similar. The overall averaged $Sh_{c}$ values are proportional to $Re_{c}^{0.5}$ on the stagnation region and the laminar flow region such as the pressure side surface. However, since the flow is fully turbulent in the near-tip region, the heat/mass transfer coefficients are proportional to $Re_{c}^{0.8}.$

• 한국유체기계학회 논문집
• /
• 제8권4호
• /
• pp.27-38
• /
• 2005

The present study investigated the effect of relative position of the blade on blade surface heat transfer. The experiments were conducted in a low speed wind tunnel with a stationary annular turbine cascade. The test section has a single turbine stage composed of sixteen guide vanes and blades. The chord length of the blade is 150 mm and the mean tip clearance of the blade is $2.5\%$ of the blade chord. The Reynolds number based on blade inlet velocity and chord length is $1.5{\times}105$ and mean turbulence intensity is about $3\%$. To investigate the effect of relative position of blade, the blade at six different positions in a pitch was examined. For the detailed mass transfer measurements, a naphthalene sublimation technique was used. In general, complex heat transfer characteristics are observed on the blade surface due to various flow characteristics, such as a laminar flow separation, relaminarization, flow acceleration, transition to turbulence and tip leakage vortices. The results show that the blade relative position affects those heat transfer characteristics because the distributions of incoming flow velocity and turbulence intensity are changed. Especially, the heat transfer pattern on the near-tip region is significantly affected by the relative position of the blade because the effect of tip leakage vortex is strongly dependent on the blade position. On the pressure side, the effect of blade position is not so significant as on the suction side surface although the position and the size of the separation bubble are changed.

• 한국정밀공학회지
• /
• 제30권9호
• /
• pp.969-975
• /
• 2013

As energy shortage is getting more serious, wind energy source is more promoted around the world. Blade is a key component of wind turbine. Local breakages and/or contamination in the blade bring degradation in aerodynamic efficiency and life-time. However, it is not easy and even dangerous for human workers to access the blade for inspection and maintenance since its size is huge and located at high mountains and rough sea, which are windy places. This paper deals with a novel moving mechanism that efficiently carries human workers or robots to the wind turbine blade. The proposed mechanism utilizes flexible tube with pressurized air that rolls and climbs over the blade surface. So, the tube naturally adapts the changing surface of the blade and acts no harm to it. This paper discusses about its concept, detail design, and advantages. The feasibility of the proposed mechanism is proved through experiments prototype.

• 풍력에너지저널
• /
• 제13권4호
• /
• pp.42-49
• /
• 2022

Today, the power capacity of a wind turbine and the size of a blade is increasing to capture more wind resources, reduce the number of wind turbines on a wind farm, and reduce the cost of energy. As the blade size becomes larger, attention is being paid to the structural integrity of the blade root connection due to the heavy gravitational load effect and increased aerodynamic loads on the large blade, which could cause catastrophic failure of the blade. Therefore, the secure bolted joint connection of the blade to the hub is very important. In this paper, attention was given to the stress concentration factor (SCF) at the first thread between the M42 bolt and nut. The effect of various design parameters on the stress concentration factor was investigated, which included nut type, nut height, and reduced shank bolt. From a close design investigation of the numerical results, it turned out that the use of a reduced shank bolt resulted in the largest reduction of the stress concentration factor by 40 %, and the round nut type also reduced the SCF by 10 %, which will be beneficial to large wind turbine blades over 100 meters.

• 한국추진공학회지
• /
• 제3권3호
• /
• pp.40-46
• /
• 1999

풍력발전용 회전날개의 공력성능과 시동특성은 정격출력 및 운용방법 등의 전체적인 시스템 성능을 결정짓는 중요한 요소이다. 따라서, 풍력발전용 회전날개를 설계한 경우 공력성능과 풍속 및 깃각에 따른 시동특성은 반드시 검토되어야 한다. 이를 위해 본 연구에서는 수평축 풍력발전용으로 개발된 회전날개의 공력성능을 해석하기 위한 프로그램을 개발하였으며, 타당성 검증을 위해 상용화 되어있는 회전날개의 공력성능해석을 수행한 결과 회사측에서 제시한 실험치와 잘 일치함을 확인하였다. 또한 개발된 공력 해석 프로그램을 바탕으로 시동특성 해석 프로그램을 개발하여 분석한 결과 우리나라와 같이 저풍속에서 운용되는 풍력발전기에는 가변깃각 제어방식이 유리함을 확인하였다.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제17권3호
• /
• pp.236-245
• /
• 2017

Purpose: There is no established inspection system for composite wind blade during the fabrication stage even though the blades are one of the most important part at wind generation system, but phased array ultrasonic testing method has been continuously studied about wind turbine blade with composite. When wind turbine blade with complex shape by phased array probe is inspected, it is necessary to study for system keeping constant pressure using pressure device. Methods: In this paper, we propose constant pressure device for inspecting wind turbine blade by phased array ultrasonic test method. Design of the device controller is based on Hunt-Crossley model. We evaluate reliability of phased array ultrasonic inspection result that applicated constant pressure device. Result: Defect indication is precise and its error is small when constant pressure mechanism based on Hunt-Crossley model was used. Conclusion: When inspection is progressed using constant pressure mechanism, the reliability of composite wind blade inspection can be improved.

• 한국유체기계학회 논문집
• /
• 제14권3호
• /
• pp.39-44
• /
• 2011

In this study, performance analyses have been conducted for a 5MW class wind turbine blade model. Advanced computational analysis system based on computational fluid dynamics(CFD) and computational structural dynamics(CSD) has been developed in order to investigate detailed dynamic responsed of wind turbine blade. Reynolds-averaged Navier-Stokes (RANS) equations with K-${\epsilon}$ turbulence model are solved for unsteady flow problems of the rotating turbine blade model. A fully implicit time marching scheme based on the Newmark direct integration method is used for computing the coupled aeroelastic governing equations of the 3D turbine blade for fluid-structure interaction (FSI) problems. Predicted aerodynamic performance considering structural deformation effect of the blade show different results compared to the case of rigid blade model.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3347-3352
• /
• 2007

This paper describes a research for the performance improvement of the straight-bladed vertical axis wind turbine. To improve the performance of VAWT, the individual blade pitch control method is adopted. For the wind turbine, CFD analysis is carried out by changing blade pitch angle according to the change of wind speed and wind direction. By this method, capacity and power efficiency of VAWT are obtained according to the wind speed and rotating of rotor, and could predict the overall performance of VAWT. It was manufactured to verify performance of the experimental system that consists of rotor including four blades and base. Furthermore, torque sensor and power generator were installed. Also, active controller which can change the pitch angle of the individual blade according to the wind speed and direction was used.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.65-71
• /
• 2002

Turbine blade is subject to cyclic bending force by steam pressure. Stress analysis by fractography is already established technology as means far seeking cause of fracture and has been widely employed. In the X-ray frctography, plastic deformation and residual stress near the fracture surface can be determined and information of internal structure of material can be obtained. Therefore, to find a fracture mechanism of torsion-mounted blade in nuclear power plant, based on the information from the fracture surface obtained by fatigue test, the correlation of X-ray parameter and fracture mechanics parameter was determined and then the stress intensity factor to actual broken turbine blade was predicted.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권1호
• /
• pp.78-83
• /
• 2005

Currently in Japan, the use of the small wind turbine is an upward trend. There are already many well established small wind turbine generators in use and their various failures have been reported. The most commonly sighted failure is blade damage. Thus the research purpose was set to develop a simple failure diagnostic system, where an Acoustic Emission (AE) signal was produced from the failure part of a blade which was measured by AE sensor. The failure diagnostic technique was thoroughly examined. Concurrently, the damage part of the blade was imitated, the AE signal was measured, and a FFT(Fast Fourier Transform) analysis was carried out, and was compared with the output characteristic. When one sheet of a blade was damaged 40mm or more, the level was computed at which failure could be diagnosed.