• 한국가시화정보학회지
• /
• 제18권3호
• /
• pp.69-76
• /
• 2020

In the present study, we investigate the flow separation characteristics of a paraglider canopy model by tuft visualization. The experiment is conducted at Re = 3.3×105 in a wind tunnel large enough to contain the three-dimensional paraglider canopy model, where Re is Reynolds number based on the mean chord length and the free-stream velocity. The flow separation characteristics of the canopy model near the wing root are similar to those of a two-dimensional airfoil with a cross-section similar to the model. On the other hand, near the wingtip region, the flow separation is suppressed by the downwash induced by the wingtip vortex. As a result, as the angle of attack increases, the flow separation occurs from the wing root region of the canopy model and develops toward the wingtip.

• 한국농공학회논문집
• /
• 제54권5호
• /
• pp.79-89
• /
• 2012

The objectives of this paper were to evaluate the wind flow behind the livestock ventilation fan for small-scale wind power generation and to make flow profiles of imaginary ventilation fan for future simulation works. The field experiments using typical 50-inch fan indicated that the wind flow behind the ventilation fan had a good possibility of power generation with its high and steady wind speeds up to a distance of 2 m. The expected electricity yield was almost 101~369 W with a small (0.8 m radius) wind turbine. The decline of ventilation fan performance caused by the obstacle was also not significant with about 4 % from a distance of 2 m. The flow profiles for the computational fluid dynamics (CFD) simulation was created by combining the direction vectors analyzed from tuft visualization test and the flow predicted by the rotating fan modeling. The flow profiles are expected to provide an efficient saving of computational time and cost to design a better wind turbine system in future works.

• 기계저널
• /
• 제33권9호
• /
• pp.803-810
• /
• 1993

벽면에서의 전단응력 분포와 유동장 내에서의 3차원 유동 요소를 추적하는 유동가시화 기법중 에서 몇 가지를 그 응용 예와 함께 살펴보았다. 3차원 유동의 주요 특징들과 한계유선(limiting streamlines)을 관찰하기 위해서는 oil and lampblack 기법이 충분하나 유속이 작거나 유동의 방향이 분명하지 않은 곳에서는 ink dot 기법을 적용하는 것이 좋다. Oil and lampblack 기법은 실험하고자 하는 유동의 조건에 따라 기름과 분말의 혼합비, 기름의 점도 등을 잘 선택하여야 한다. 안장점(Saddle point) 이나 재부착선(reattachment line)과 같이 성격상 중요한지점을 찾기 위해서는 털실 프로브(single tuft probe)가 유용하게 쓰이며, 이는 또 유동내에서 와동의 존재와 위치를 찾는데 쓰이기도 한다. 수치해석 결과 얻을 수 잇는 속도벡터와 같이 비교적 넓은 유동 장을 한눈에 관찰하기 위해서는 털실 격자망 (tuft grid)을 사용할 수 있으며 각 털실은 그 지 점세서의 유동의 방향과 그 안정성(steadiness)를 나타내준다. 이러한 유동가시화 방법들은 각 유동의 특성에 맞는 적절한 조건을 맞추기 위해서 많은 시행착오를 거쳐야 하며, 하나의 만족 스러운 결과를 얻기 위해서는 많은 기술과 시간과 연습을 요구하고 있어서 다른 정량적인 측정 기술과 더불어 커다란 노력과 관심을 기울여서 발전시켜야만 할 것이다.

• 대한기계학회논문집
• /
• 제13권1호
• /
• pp.178-189
• /
• 1989

본 연구에서는 우선 승용차의 1/10 모형의 형상을 더욱 단순화시킨 2차원 자동차형 물체를 대상으로 하여 그 주위의 압력, 속도 및 난류량의 분포를 측정하고, 또한 울터프트(wool tuft)를 이용한 유동가시화법으로 후류구조를 파악함으로써 향후 계속될 실험적 및 수치해석적 연구의 기초를 마련하고자 한다.

• Wind and Structures
• /
• 제5권6호
• /
• pp.515-526
• /
• 2002

The wind flow over two-dimensional sinusoidal hilly obstacles with slope (the ratio of height to half width) of 0.5 has been investigated experimentally and numerically. Experiments for single and double sinusoidal hill models were carried out in a subsonic wind tunnel. The mean velocity profiles, turbulence statistics, and surface pressure distributions were measured at the Reynolds number based on the obstacle height(h=40 mm) of $2.6{\times}10^4$. The reattachment points behind the obstacles were determined using the oil-ink dot and tuft methods. The smoke-wire method was employed to visualize the flow structure qualitatively. The finite-volume-method and the SIMPLE-C algorithm with an orthogonal body-fitted grid were used for numerical simulation. Comparison of mean velocity profiles between the experiments and the numerical simulation shows a good agreement except for the separation region, however, the surface pressure data show almost similar distributions.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권3호
• /
• pp.315-323
• /
• 2016

This paper deals with experimental investigation of active flow control via synthetic jets using an unmanned combat air vehicle (UCAV) planform. Fourteen arrays of synthetic jets, mounted along both leading edges, were fully or partially activated to increase aerodynamic efficiency and reduce pitch-up moment. The measurements were carried out using a six-component external balance, a pressure scanner, and tuft flow visualization. It was observed that aerodynamic efficiency (L/D) and pitching moment were clearly affected by the location of jets. In particular, inboard and outboard actuation could effectively increase L/D. Moreover, inboard actuation showed a reduction in the pitch-up, even more than that generated by the full actuation. These results suggest that inboard actuation not only effectively increases L/D but also reduces the pitch-up using only a few actuators.

• 설비공학논문집
• /
• 제13권3호
• /
• pp.209-216
• /
• 2001

A numerical study is peformed to investigate the effect of circumferential velocity generated by the guide vane on the nozzle flow of a jet fan, s a way of increasing the penetration force of jet fan with nozzle of 175mm diameter. For the validation of numerical results. the velocity is measured by a 5-hole pitot tube and flow visualization is conducted by the tuft method. Under the inlet condition that the maximum circumferential velocity in the stator outlet of the present jet fan is 1.8m/s, the axial velocity in the nozzle outlet has the feature that the velocity at the axis is low and the velocity near the wall high. Therefore, to increase the throw length of the jet fan, the configuration of the fairing and nozzle needs to be developed and the precise revise of the stator angle is required, In addition, the bigger the circumferential velocity, the smaller the axial velocity at the axis and the bigger non-uniformity of the flow distribution.

• 오토저널
• /
• 제12권3호
• /
• pp.53-62
• /
• 1990

A wind tunnel experiment for the flow around a 1/5 scale passenger vehicle model has been carried out. A 5-hole Pitot tube is used for measuring velocity distributions around the model and a scanivalve with 48 ports is used for measuring surface pressure distribution at various Reynolds numbers. In order to observe the flow on the surface and in the wake region, a flow visualization experiment has been performed using wool tuft with and without paper cones. In addition, a 2-dimensional viscous calculation considering only the mid-plane section of the model has been performed. A complex wake structure in the immediate rear of the model has been confirmed. The distributions of the surface pressure coefficient are not sensitively dependent on the Reynolds Number. In the first half of the model, they do not seem to vary form section to section. However, in the second half, they do vary from section to section, especially at the bottom surface, which indicates that the cross flow vortex is more affected by the bottom surface than the top surface. The qualitative agreement of the measured and calculated velocity field also explains the usefulness of the 2-dimensional calculation in the limited sense.

• 한국해양공학회지
• /
• 제25권1호
• /
• pp.22-26
• /
• 2011

The resistance performances of a small leisure yacht with two different keels, center and double, respectively, are investigated using a model test at circulating water channel and CFD analysis. Flow patterns around the keels are observed using a tuft test to make clear the relation between the resistance performance and the flow characteristics around the keels. The results show that the keel does not affect free surface flows and that the double keel yacht has better performance compared to a single keel yacht in oblique condition from the resistance point of view.

• 해양환경안전학회지
• /
• 제20권1호
• /
• pp.78-85
• /
• 2014

일반상선 중 액화천연가스(LNG) 재기화 선박은 기존의 LNG 운반선에 액화된 LNG를 다시 기화할 수 있는 추가설비를 갖춘 선박이다. 이 선박은 해상에서 천연가스를 해저 터미널을 통해 이송하는 수중 터렛 시스템을 보유한다. 하역작업을 완료한 선박이 운항 시에는 수중 터렛이 없음으로 인해 선수부 바닥이 열려 있는 개구부 즉, 오프닝 상태가 발생한다. 본 연구의 주 목적은 오프닝 상태로 운항 시 발생되는 속도손실을 CFD를 이용한 유동해석과 예인수조에서의 모형시험을 통하여 정확하게 파악하였다. 모형시험에서는 나선 상태와 오프닝 상태에서 저항 및 자항성능을 평가하였다. 실험에서는 터프트 법에 의한 유선조사시험을 이용하여 오프닝 내부유동의 변화를 정량적 또는 정성적으로 보다 더 상세한 조사를 하였다.