• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.10a
• /
• pp.76-85
• /
• 1995

The general equation of homogeneous strin for tube drawing has been derived. This can be applied to the general tube drawing method for non-zero plug angle. Also, the derived equation can represent Blazynski's equations for the sinking and tube drawing with a constant plug diameter. The general tube drawing was divided into two steps, sinking and contact drawing zones. The derived equation can calculate the homogeneous strains of the two steps. The various tube drawing methods such as fixed tapered plug, fixed mandrel, fixed back tapered plug, and floating plug have been analysed by the equation and finite element analysis. From the FEM calculations, the total strains and drawing stresses are obtained and consequently the redundancy factor of various drawing methods was analysed. The fixed back tapered plug method showed the largest redundancy factor and the floating plug method had the largest drawing stress.

• Transactions of Materials Processing
• /
• v.13 no.8
• /
• pp.671-677
• /
• 2004

For the large reduction in tube cross section, the tube drawing process is usually performed by two successive passes, so called first drawing and second drawing. In multi-pass drawing process, the reduction balance is important to prevent drawing cracks. Therefore in this study, the model for uniform reduction distribution in two-pass drawing process has been developed on the basis of cross sectional variation of drawn tube. For the given product geometry the model provides optimal diameter and thickness that can evenly distribute drawing reductions. The capability of model is well confirmed by finite element analysis of tube drawing process. Criteria curves at various limit strains to determine whether the drawn tube would fail during drawing process are also proposed by using newly developed model.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.35-38
• /
• 2004

In general, tube drawing process is composed of two steps, so called first drawing and second drawing. Drawing cracks are mainly occurred during the 2nd drawing process due to the improper drawing process. In order to analyze the reduction distribution in successive two-step drawing process, tube drawing process was simulated by finite element method. From the finite element analysis, the balance between first and second reduction is proved to be important factor to prevent drawing cracks. Hence the numerical expression was developed for tube drawing process to distribute even strain and criteria curves that can predict the safe drawing region were also proposed using this numerical formula.

• Transactions of Materials Processing
• /
• v.24 no.5
• /
• pp.340-347
• /
• 2015

Multi-pass shape drawing is used to manufacture long products of arbitrary cross-sectional shapes. This process allows smooth surface finishes and closely controlled dimensions of the cross-sectional shape. Tube shape drawing for hollow type products provides material savings and weight reduction. The intermediate die shapes are very important in multi-pass tube shape drawing. In the current paper, the design method for the intermediate dies in a tube shape drawing process is developed using a die offset for corner filling (DOCF) method. Underfill defects are related to the radial velocity distribution of each divided section in the deformation zone. The developed intermediate die shape design was applied to the two-pass tube shape drawing with fixed mandrel for manufacturing a hollow linear motion (LM) guide rail. The proposed design method led to uniform and steady metal flow at each divided section. FE-simulations and experiments were conducted to validate the effectiveness of the proposed method in multi-pass tube shape drawing process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.333-336
• /
• 2008

There are many different kinds of forming processes to make a tubular product such as hydroforming and tube drawing. However, we should consider a better forming process in view point of energy consumption and $CO_2$ emission to save our earth. In this paper we have conducted FEM simulations to the various forming processes for sheet and tubular products to compare their energy consumptions. One example is tubular product and the other for drawn cup. From the comparisons of total energy for hydrofroming and tube sinking processes, hydroforming is consumed more energy than tube drawing. Also the cup drawing from sheet metal and tube sinking for the cup with flange indicate that the tube sinking is better than cup drawing of sheet metal in energy consumption.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.03b
• /
• pp.40-47
• /
• 1996

An upper bound solution of tube drawing process using a fixed tapered plug has been obtained , which reduces to an solution for tube sinking by setting friction factor between tube and plug at zero. Effects of various process paraments have been discussed based on the solution.

• Transactions of Materials Processing
• /
• v.20 no.8
• /
• pp.562-567
• /
• 2011

This paper deals with effects of certain important factors in a tube drawing operation, such as the use of a mandrel, die radius and tangential angle at die outlet, on the deformation behavior of a small-diameter seamless tube. Both experimental and finite element simulation studies are carried out to assess the effects of the above parameters. Experiments and finite element predictions are compared. The use of a mandrel simplifies the design of tube drawing, but also induces some difficulties from increased process complexity. The effects of die outlet tangential angle and radius are discussed in detail.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.7
• /
• pp.24-31
• /
• 1999

Bulging is a forming method to shape of die cavity by using hydraulic pressure in tube or vessel. Bulging machine and die were developed in order to produce vessel for keeping warm. Bulging machine is a double type with two horizontal cylinders for bulging of two pieces at the same time. The developed die system has one bulging die and two drawing dies for necking at the both ends of tube. The diameter of tube expands by hydraulic pressure in tube. at the same time, thrust at the both ends of tube. pushes tube in the direction of expansion to obtain high expanding rate with no crack. In this study, the bulging properties were investigated to solve tube crack and necking in manufacturing vessel by the combination method of bulging and drawing. As a result, high expanding rate of tube radius without crack, precision necking and high productivity were obtained.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.4
• /
• pp.40-46
• /
• 2001

Bulging is a forming method to shape die cavity by using hydraulic pressure in tube or vessel. Bulging machine and die were developed in order to produce vessel for keeping warm. Bulging machine is a double type with two horizontal cylinders for bulging of two pieces at the same time. The developed die system has one bulging die and two drawing dies for necking at both ends of the tube. The diameter of tube expands by hydraulic pressure in tube. At the same time, thrust at both ends of the tube pushes tube in the direction of expansion to obtain high expansion rate with no crack. In this study, the bulging properties were investigated to solve tube crack and necking in manufacturing vessel by combining bulging and drawing. As a result, high expanding rate of tube radius without crack, precision necking and high productivity were obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.11 s.188
• /
• pp.78-84
• /
• 2006

The objective of this study is to design the optimal die profile that can prevent material fracture in the tube drawing process for automobile steering input shaft. First, the CDV(Critical Damage Value) of material is obtained by the compression test and FE-analysis. The occurrence of fracture is estimated by the FE-analysis considering the CDV. In order to achieve the objective of this study, optimization technique and FE-analysis are applied. FPS(Flexible Polyhedron Search) method, which is one of the non-gradient optimization techniques often used in engineering, is used to search optimal die profile. The drawing die profile is represented by Bezier-curve to generate all the possible die profile. Using FPS method and FE-analysis the optimal drawing die profile is determined. To verify tile effectiveness of the redesigned optimal die, the tube drawing experiment is performed. In the experimental result, it is possible to produce sound product without material fracture using the redesigned optimal die.