• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.357-363
• /
• 2015

The development of the environment-friendly tire that meets the standard requirements according to tire labeling system can be improved through using highly homogeneous silica immobilized zinc oxide nanoparticles. In this study, a considerable amount of nanoporous silica was essentially added into nano zinc oxide to improve the physiochemical properties of the formed composite. The introduction of nanoporous silica materials in the composite facilitates the improvement of the wear-resistance and increases the elasticity of the tread. Therefore, the introduction of nanoporous silica can replace carbon black as filler in the formation of composites with desirable properties for conventional green tire. Herein, mesoporous silica immobilized zinc oxide nanoparticle with desirable properties for rubber compounds was investigated. Composites with homogeneous dispersion were obtained in the absence of dispersants. The dispersion stability was controlled through varying the molar ratio, ageing time and mixing order of the reactants. A superior dispersion was achieved in the sample obtained using 0.03 mol of zinc precursor as it had the smallest grain size (50.5 nm) and then immobilized in silica aged for 10 days. Moreover, the specific surface area of this sample was the highest ($649m^2/g$).

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.2
• /
• pp.193-199
• /
• 2014

In this paper, we present an overview of the structure of a lab-built powered knee prosthesis and the control of it. We build a powered prosthesis prototype on the basis of previous researches and aim at obtaining the essential technology related with its control. We adopt the slider-crank mechanism with a DC motor as an actuator to manipulate the knee joint. We also build an embedded control system for the prosthesis with a 32-bit DSP controller as a main computation unit. We divide the gait phase into five stages and use a FSM (Finite State Machine) to generate a torque reference needed for each stage. We also propose to use a position-based impedance controller for driving the powered knee prosthesis stably. We perform some walking experiments at fixed speeds on a tread mill in order to show the feature of the built powered prosthesis. The experimental results show that our prosthesis has the ability to provide a functional gait that is representative of normal gait biomechanics.

• Korean Journal of Applied Biomechanics
• /
• v.27 no.3
• /
• pp.181-187
• /
• 2017

Objective: The aim of the study was to compare & analyze on the variations of ground reaction force during ascending and descending of bus stair. Method: Simulated wooden stair of bus (raiser: 37.66 cm, width: 109 cm, tread: 29 cm) and GRF system (AMTI-OR-7/ AMTI., USA) was set up within experimental room. Adult female (n=8) performed ascending & descending of simulated bus stair, and variables analyzed consisted of TT (transfer-time), PVF (peak vertical force), LR (loading rate), DR (decay rate), CV (coefficient of variation) and AI (asymmetry index). Sample data from GRF cut off at 1,000 Hz. Results: TT showed shortest variation at phase 1 during descending, but longest variation at phase 1 during ascending of stair. PVF19 (Fz2, 100%) showed large pattern during descending than that of ascending, but rather showed small pattern during ascending of stair in case of PVF2 (Fz4). LR showed larger pattern during descending than that of ascending, but rather during ascending of stair in case of DR. Variation of CV (%) did not show difference between LR and DR, but showed higher possible occurrence of variation during descending of stair. Also AI (%) showed higher index during ascending than that of descending of stair. Conclusion: Because introduction of lowered bus stair has various realistic problems, if lined up at designated bus stopage exactly, rather can solve problems of inconvenience, reduce impulsive force and secure a stability of COG during ascending & descending of stair.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.6
• /
• pp.802-808
• /
• 2011

One of the important mechanical properties of cryogenic temperature structure material is fracture toughness. Research on normalization of fracture toughness test method is becoming very important issue with development of cryogenic structural elements. Specially, mechanical properties estimation by each micro-structure of welding department is important because it can cause unstable fracture when use under cryogenic environment in case of welding department. In this study, fracture toughness estimation test was carried out to unloading compliance method and sensitization heat-tread minimized test specimen at liquid nitrogen (77K), liquid helium (4K), 293K temperature to STS-316L base metal and weld metal.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.4
• /
• pp.277-283
• /
• 2006

As the products such as HDD, Notebook, PDA, and Mobile Phone become smaller and thinner, the radius of threads as well as holes for assembling those products become smaller, even down to 1mm. To produce such small holes and thread efficiently, multi tapping is highly necessitated. However the multi tapping characteristics is not well known because its complicated cutting mechanism and thus the quality of the produced holes and threads is not well studied yet. In this paper, experiments have been conducted for small-radius threads using M2 and M2.6 and M3 cold forming tap to investigate multi tapping process using several useful signal such as torque and Z-axis encoder pulse. The surface and profile of the machined threads have been magnified and observed through a SEM.

• Journal of Korean Society for Atmospheric Environment
• /
• v.2 no.2
• /
• pp.60-65
• /
• 1986

Atmospheric particulates were collected at a site near the front gate of the Yonsei University using nine stages Andersen air sampler and the distribution of seasonal particle size was investigated. Rubber, Pb and Zn contents of the collected particulates in each stage were determined. Particle size distribution of atmospheric particulate, which was made by concentration distribution curve method, was usually divided into two groups, course (particles larger than 1 - 2 $\mu m in diameter$) and fine (particles smaller than 1 - 2 \mu m in diameter$) groups, regardless of sampling period. More than 80 percent of the total rubber contents in atmospheric particulates were larger than $5 \mu m$ in diameter, meaning that most of rubber particles were originated from tire tread. After benzene extraction for 4 hrs, the extracts were analyzed by Curie-point pyrolysis gas chromatography for rubber content. Pb and Zn contents were determined by atomic absorption spectroscopy. The annual average concentration of rubber particles was $4.2 \mu g/m^3$, which corresponded to 2.2% of the annual average total suspended particulates. Average concentration of styrene brtadiene rubber was about five times that of natural rubber. Annual average concentrations of Pb and Zn were $1.2 \mu g/m^3 and 0.4 \mu g/m^3$ respectively, which corresponded to about 0.7% and 0.2% of the annual average total suspended particulates.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.2
• /
• pp.80-91
• /
• 1995

A theoretical models has been prepared which describes the noise generated by tire/road interaction for the tire structure-borne sound analysis. The model begin with a set of thin shell equations describing the motion of the belt of a radial ply tire, as drived by Bohm('mechanisms of the belted tire', Igeniur-Archiv, XXXV, 1966). Structural quantities required for these equations are derived from material properties of the tire. The rolling shape of a tire is computed from the steady-state limit of these equations. Vibrational response of the tire is treated by the full dependent shell equations. The force input at the tire/road interface is calculated on the basis of tread geometry and distribution of contact patch pressure. Radiation of noise is calculated by a simpson integral. Using the programs, the effect on noise of various tire design variations is computed and discussed. Trends which lead to quiet tire design are identified.

• Korean Journal of Agricultural Science
• /
• v.37 no.1
• /
• pp.37-43
• /
• 2010

This study carried out to develop barrier-free certification program in forest trail. It is done to provide the certification system presented about certification organized, certification standard and indexes, evaluation method and operation plan. In order to develop certification program in forest trail, detailed measurement index must be developed earlier based on an accessbility, a stability, a preservation and a walking continuity. The suitable forest trail for weak pedestrian was investigated that running slope should be 1/20(5%) maximum, cross slope cannot exceed 1/50(2%) maximum and clear tread width should be above of minimum 90cm. In addition, the trail type is designed as a mixed trail system which is a combination of the loop and the line form and its distance should be 225~675m. Finally, forest trail should be manage sustainably by having regular monitoring and evaluation.

• Journal of the Korean housing association
• /
• v.24 no.6
• /
• pp.51-59
• /
• 2013

The ritual for community is a group ritual performed by the regional community of a village for the safety of the residents and abundant harvests. However, many ritual places have been destroyed by the anti-superstition movement, New Community Movement (Saemaul Movement), industrialization and urbanization since the 1960s. Under the circumstances, this study researched the status of use of the ritual place in Beommul-dong in Daegu where the ritual was revived in 2004 after having been suspended since the end of the 1980s due to urbanization. The revival of the ritual for community in Beommul-dong in Daegu, which had been maintained by the village people alone, is the prime example of the vitalization of local community as the recreation of local community, since the ritual has been transformed into a kind of festival involved with and financed by the local government. The study on analyzing the usage pattern of the ritual place may provide useful sources to come up with the modernized functions of the ritual place as a community place, where the heads of the ward office and cultural center, lawmakers and most of the residents perform the ritual, share foods and tread on the God of the Earth across the village at 11:30 in the morning on every January 16 of the lunar calendar.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.346-349
• /
• 2015

Generally, in order to verify the degree of tire wear or abnormal wear, a driver or an auto mechanic checks the degree of tire wear and the existence of tire abnormality, directly with the naked eye or by way of using a gauge equipment. In case of such verification, individual subjective judgments may be involved or a driver may suffer heavy burdens to expend the time and cost for using the wheel alignment equipment. Therefore, this thesis will use a number of laser sensors to check the existence of abnormal wear and the degree of wear on each tire and develop a system checking the sides of tires to receive the tire information, so that subjective judgments may be overcome and objective and accurate judgments may be rendered.