• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.898-901
• /
• 2006

To fabricate mono layer green sheet (MLGS) of transparent dielectric for PDP front panel, dispersion of transparent dielectric slurry and various properties of green sheets were examined as a function of amount and kinds of organic additives. Sedimentation height and viscosity of slurry were measured to determine proper types and amount of dispersant in non-aqueous system transparent dielectric slurry. Many MLGS having various ratios of the transparent dielectric glass frit, binder and plasticizer were fabricated. Finally we got the transparent dielectric layer of high transparency and free from residual pore might be remained in the gap between the electrodes.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1248-1251
• /
• 2005

In PDP, a transparent dielectric is formed on a front glass substrate so as to cover bus electrodes (Ag). During the fabrication process, sometimes, a transparent dielectric reacts with bus (Ag) electrode in the range of $560-600^{\circ}C$, and the reaction gives the dielectric its yellow coloration, what is called "yellowing phenomena". In this paper, we investigated the reaction between bus electrode and transparent dielectric covered with different frit content in Ag paste.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.864-866
• /
• 2007

In PDP, bus electrode should have low resistance for high efficiency. The transparent dielectric affects the shape change of bus electrode during the firing. These are related with the electrical property of the electrode. In this study, the shape of electrode was controlled by firing schedules of the transparent dielectric and the bus electrode.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.276-276
• /
• 2014

High-performance, fully-transparent, and top-gated oxide thin-film transistor (TFT) was successfully fabricated with Ta2O5 high-k gate dielectric on a glass substrate. Through a self-passivation with the gate dielectric and top electrode, the top-gated oxide TFT was not affected from H2O and O2 causing the electrical instability. Heat-treated InSnO (ITO) was used as the top and source/drain electrode with a low resistance and a transparent property in visible region. A InGaZnO (IGZO) thin-film was used as a active channel with a broad optical bandgap of 3.72 eV and transparent property. In addition, using a X-ray diffraction, amorphous phase of IGZO thin-film was observed until it was heat-treated at 500 oC. The fabricated device was demonstrated that an applied electric field efficiently controlled electron transfer in the IGZO active channel using the Ta2O5 gate dielectric. With the transparent ITO electrodes and IGZO active channel, the fabricated oxide TFT on a glass substrate showed optical transparency and high carrier mobility. These results expected that the top-gated oxide TFT with the high-k gate dielectric accelerates the realization of presence of fully-transparent electronics.

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.277-283
• /
• 2004

To fabricate green sheet of transparent dielectric for PDP front panel, dispersion of transparent dielectric slurry, density, and mechanical properties of green sheets have been investigated as a function of amount and composition of organic additives. Measurements of sedimentation and viscosity were employed to determine a proper dispersant and its amount for a well dispersed transparent dielectric powders in non-aqueous system. Green sheets, having various ratios of transparent dielectric powders to transparent dielectric powders＋ binder＋plasticizer and binder to binder＋plasticizer, were fabricated. All the tape casting slurries showed shear thinning effect, that is, the apparent viscosity decreased with the increase of shear rate. It was found that the amount and composition of organic additives were main variables to affect densities and mechanical properties of transparent dielectric green sheets for PDP.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1107-1113
• /
• 2004

Dry film method for large size of PDP(Plasma Display Panel) module has been actively investigated. This method for lead-free transparent dielectric formation depends on green sheet technology. By adjusting the composition of transparent dielectric powders and organics, uniformly dispersed slurry was fabricated, Viscosity of the slurry exhibited pseudoplastic behavior for tape casting, Cast green sheets were tested under tensile condition at room temperature. It was found that the increase in transparent dielectric powder and binder ratio leads to decrease in strain to failure of green sheets from 120 % to 34 % and from 255 % to 4 %, respectively. Tensile strength of green sheets decreased abruptly with increase of transparent dielectric powder ratio, with minimum at 0.13 MPa. On the other hand, tensile strength increased continuously from 0.1 MPa to 2.4 MPa with increase of binder ratio. The green sheets were attached on the glass substrate and heated by following firing schedule. As a result, the best result was obtained when fired at 580 $^{\circ}C$ for 15 min and had transmittance of 78 % in visible range 550 nm.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.4
• /
• pp.286-289
• /
• 2018

This paper tests the feasibility of using the transparent electrode as the electrode of the capacitor in order to use the vehicle glass of the electric vehicle for a capacitive coupling wireless transfer (CCWPT). Large coupling capacitance can be obtained due to large area and high permittivity using the glasses of an electric vehicle. However, if an electrode is formed on a metal such as copper, then a view cannot be guaranteed and a transparent electrode can pose a solution. Therefore, the coupling capacitor is implemented by forming a glass dielectric with an ITO transparent electrode on one side through a semiconductor deposition process. The loss of the coupling capacitor is investigated, and a 200 W CCWPT prototype is fabricated and tested for its characteristics and power transfer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.491-491
• /
• 2011

Transparent and flexible electronic devices that are light-weight, unbreakable, low power consumption, optically transparent, and mechanical flexible possibly have great potential in new applications of digital gadgets. Potential applications include transparent displays, heads-up display, sensor, and artificial skin. Recent reports on transparent and flexible field-effect transistors (tf-FETs) have focused on improving mechanical properties, optical transmittance, and performances. Most of tf-FET devices were fabricated with transparent oxide semiconductors which mechanical flexibility is limited. And, there have been no reports of transparent and flexible all-organic tf-FETs fabricated with organic semiconductor channel, gate dielectric, gate electrode, source/drain electrode, and encapsulation for sensor applications. We present the first demonstration of transparent, flexible all-organic sensor based on multifunctional organic FETs with organic semiconductor channel, gate dielectric, and electrodes having a capability of sensing infrared (IR) radiation and mechanical strain. The key component of our device design is to integrate the poly(vinylidene fluoride-triflouroethylene) (P(VDF-TrFE) co-polymer directly into transparent and flexible OFETs as a multi-functional dielectric layer, which has both piezoelectric and pyroelectric properties. The P(VDF-TrFE) co-polumer gate dielectric has a high sensitivity to the wavelength regime over 800 nm. In particular, wavelength variations of P(VDF-TrFE) molecules coincide with wavelength range of IR radiation from human body (7000 nm ~14000 nm) so that the devices are highly sensitive with IR radiation of human body. Devices were examined by measuring IR light response at different powers. After that, we continued to measure IR response under various bending radius. AC (alternating current) gate biasing method was used to separate the response of direct pyroelectric gate dielectric and other electrical parameters such as mobility, capacitance, and contact resistance. Experiment results demonstrate that the tf-OTFT with high sensitivity to IR radiation can be applied for IR sensors.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.632-634
• /
• 2002

Transparent dielectric layer having color-filter function in front panel for PDP(Plasma Display Panel) was successfully fabricated and characterized. Transparent dielectric layer in front panel was made of glass based on $PbO-SiO_2-B_2O_3$ ternary system. The change of properties with content variation of oxide colorants in transparent dielectric layer having color-filter function was systematically accessed. It was demonstrated that the optimized content of oxide colorants to parent glass could greatly increase up contrast ratio and color temperature without significantly degrading luminance.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.187-188
• /
• 2000

The conventional firing process method for the transparent dielectric layer in PDP Technology has disadvantages of low through put, high power consumption and large process area. We propose the rapid thermal scinterring (RTS) method as new process method to overcome these disadvantage characteristics. As the experimental result of this method, the optic transmittance(wavelength : 600nm) rate of transparent dielectric layer was more improved than conventional furnaces under the optimized gas supplying. Further, it was certified this method had the best conditions on the firing process of the PDP transparent dielectric layer.