• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.9
• /
• pp.25-37
• /
• 2007

The existing route re-establishment methods which intend to extend the lifetime of the network attempt to find new routes in order not to overly consume energy of certain nodes. These methods outperform other routing algorithms in the network lifetime extension aspect because they try to consume energy evenly for the entire network. However, these algorithms involve heavy signaling overheads because they find new routes based on the flooding method and route re-acquisition occurs often. Because of the overhead they often can not achieve the level of performance they intend to. In this paper, we propose a new route re-acquisition algorithm ARROW which takes into account the cost involved in the packet transmission and the route re-acquisition. Since the proposed algorithm considers future route re-acquisition costs when it first finds the route, it spends less energy to transmit given amount of data while evenly consuming the energy as much as possible. Using 2-dimensional Markov Chain model, we compare the performance of the proposed algorithm and that of other algorithms. Analysis results show that the proposed algorithm outperforms the existing route re-acquisition methods in the signaling overhead and network lifetime aspects.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.8 s.99
• /
• pp.815-824
• /
• 2005

In this paper, we proposed a new DGS(Defected Ground Structure) Doherty amplifier for IMT-2000 band. Originally, active load-pull analysis of a Doherty amplifier assumes ideal harmonic termination condition. However, there have been no papers considering this ideal harmonic termination condition. We obtained excellent improvements of efficiency, gain, maximum output power as well as superior size reduction of a Doherly amplifier by satisfying the overlooked assumption of ideal harmonic termination through the adaptation of DGS at the output transmission line of carrier and peaking amplifier that is essential for Doherty operation. The amount of both the 2nd and the 3rd harmonic rejection of the proposed DGS Doherty amplifier over the conventional one are 44.92 dB and over 23.77 dB, respectively. The acquired improvement in Pl dB, gain, drain efficiency, and ACPR to WCDMA 1FA signal were 0.42 dB, 0.33 dB, $6.4\%$ and 5.4 dBc, respectively. Moreover, electrical length of $90{\circ}$ is reduced at each of the DGS carrier amplifier path and DGS peaking amplifier path, therefore the whole amplifier circuit size is considerably reduced.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.681-689
• /
• 2010

We will demonstrate a novel topology for the feedforward amplifier. This amplifier does not use a delay element thus providing an efficiency enhancement and a size reduction by employing a distributed element negative group delay circuit. The insertion loss of the delay element in the conventional feedforward amplifier seriously degrades the efficiency. Usually, a high power co-axial cable or a delay line filter is utilized for a low loss, but the insertion loss, cost and size of the delay element still acts as a bottleneck. The proposed negative group delay circuit removes the necessity of the delay element required for a broadband signal suppression loop. With the fabricated 2-stage distributed element negative group delay circuit with -9 ns of total group delay, a 0.2 dB of insertion loss, and a 30 MHz of bandwidth for a wideband code division multiple access downlink band, the feedforward amplifier with the proposed topology experimentally achieved a 19.4 % power added efficiency and a -53.2 dBc adjacent channel leakage ratio with a 44 dBm average output power.

• Korean Journal of Childcare and Education
• /
• v.10 no.4
• /
• pp.133-158
• /
• 2014

The purpose of this study was to understand the experiences of the young children's mothers who participated in Respected Parents & Respected Children(RPRC) through a phenomenological approach. Data were collected from 9 mothers of preschool children using weekly journals, self-reported worksheets, observer's descriptive notes and reflective notes, and semi-structured pre-interviews and post-interviews to share their experiences regarding their participation in the program. From a phenomenological study, that is one of the qualitative analysis methods, 7 theme categories and 16 lower categories emerged. Theme categories were (1) the intrinsic motivation for participation in parent education program, (2) the beginning of change: mother, (3) the beginning of change: children, (4) the lasting conflicts, (5) the absence of positive parent's role model and intergenerational transmission of parenting, (6) the raising parenting efficacy, (7) the emotional supporting experience from parent education program and expectations of the continuous education course. Discussions and the implications for support practices and interventions were provided.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.1
• /
• pp.43-51
• /
• 2015

At present, in the case of small and medium window manufacturers in South Korea, glazing and window frame manufacturers are divided into separate businesses. However, in the fenestration energy consumption efficiency rating system and the energy-saving design criteria for buildings, the coefficient of overall heat transmission standard for windows is defined by window sets, which integrate glazing and window frames. At most construction sites, windows are constructed by installing separately supplied glass and frames. Research that can integrate the reality and the system is therefore necessary. The present study first investigated and analyzed the on-site situation of the fenestration energy consumption efficiency rating system. According to the results, while overall understanding of the fenestration energy consumption efficiency rating system was high, satisfaction with it was low, and the general practice at construction sites was to use windows assembled on site rather than integrated window systems manufactured at factories, thus making it difficult to confirm that the current rating system was well applied on site. Consequently, the reality of industrial sites must be reviewed and a realistic alternative to the fenestration energy consumption efficiency rating system must be presented instead of focusing on theory.

• Korean Journal of Biological Psychiatry
• /
• v.3 no.2
• /
• pp.240-244
• /
• 1996

The effects of chronic treatment with haloperidol on the binding capacities of dopamine(DA) $D_2$-like receptor were investigated in rat striatum and olfactory tubercle. The authors tried to confirm the dose-response effects with usual dose and low dose haloperidol. Rats were treated with haloperidol(0.05, 0.15, 0.5, 1.5mg/kg/day in drinking water) for four weeks. Saturation analysis of the binding of [$^3H$]spiperone to striatal membranes showed that the haloperidol treatment(0.05, 0.5, 1.5mg/kg) induced significant proliferation. The changes of dissociation constant(Kd) were not significant in striatum. The maximal binding density(Bmax) and Kd increased remarkably following the treatment with usual dose haloperidol (1.5mg/kg) in olfactory tubercle. Although there was increasing trend other the treatment with low dose haloperidol, the change of Bmax was not significant statistically. The present findings indicate that low dose haloperidol induces the proliferation of DA $D_2$-like receptor in striatum and interact with the dopaminergic transmission which might underlie the antipsychotic effect. This finding may support the recent clinical suggestion on the low dose strategy in the treatment of schizophrenia.

• Korean Journal of Materials Research
• /
• v.4 no.1
• /
• pp.9-23
• /
• 1994

Epitaxial $CoSi_2$ layer has been grown on NaCl(100) substrate at low deposition temperature($200^{\circ}C$) by multitarget bias cosputter deposition(MBCD). The phase sequence and crystallinity of deposited silicide as a function of deposition temperature and substrate bias voltage were studied by X-ray diffraction(XRD) and transmission electron microscopy(TEM) analysis. Crystalline Si was grown at $200^{\circ}C$ by metal induced crystallization(M1C) and self bias effect. In addition to, the MIC was analyzed both theoretically and experimentally. The observed phase sequence was $Co_2Si \to CoSi \to Cosi_2$ and was in good agreement with that predicted by effective heat of formation rule. The phase sequence, the CoSi(l11) preferred orientation, and the crystallinity had stronger dependence on the substrate bias voltage than the deposition temperature due to the collisional cascade mixing, the in-situ cleaning, and the increase in the number of nucleation sites by ion bombardment of growing surface. Grain growth induced by ion bombardment was observed with increasing substrate bias voltage at $200^{\circ}C$ and was interpreted with ion bombardment dissociation model. The parameters of $E_{Ar}\;and \alpha(V_s)$ were chosen to properly quantify the ion bombardment effect on the variation in crystallinty at $200^{\circ}C$ with increasing substrate bias voltage using Langmuir probe.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.177-182
• /
• 2005

Montmorillonite (MMT) modified with siloxane diamine was reacted with a reactant obtained from 4,4'-diphenyl methane diisocyanate (MDI) and polyester type polyol, $Nippollan4010(\bar{M}_n2000)$. Finally, polyurethane (PU)/MMT composites were prepared by using 1,4-butane diol as a chain extender in $25\;wt\%$ solution of N,N-dimethyl acetamide (DMAc). It was expected that these nanocomposites had superior exfoliation property to that of MMT dispersed polyurethanes produced by simple mixing due to insertion of siloxane main chain to the silicate interlayer of MMT. Extent of reaction and formation of final products were analysed by using FT-IR spectroscopy. Dispersion into the PU and intercalation of MMT were identified by applying X-ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile data were acquired by universal test machine (UTM). Thermal stability and variation of surface energy were characterized by thermal gravimetric analysis (TGA) method and measurement of contact angle on the synthesized composites, respectively. As the results the organo-MMT modified with siloxane diamine in the PU composites has an intercalated structure relatively well-expanded rather than a completely exfoliated structure. The tensile strengths and the moduli for the PU/organo-MMT composites were drastically enhanced in comparison to those of $PU/Na^+-MMT$ composites.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1613-1613
• /
• 2001

Fats and molasses are used, at the present time, in a considerable proportion as ingredients for the animal feed industry. They are mainly used as energy sources, but also they provide other characteristics of technological and nutritional interest (dust reduction, increase in palatability, etc). Both semi-liquid ingredients have numerous aspects in common from the point of view of their use in livestock feeds, as well as of their analytical control. Feed manufacturers use several criteria to evaluate the quality of fat and molasses. Furthermore, the traditional methods currently used, for their evaluation (eg. fatty acids, sugars, etc) are expensive and more sophisticated that the traditionally used for solid ingredients. The objective of the present work is to carry out a viability study to evaluate the ability of NIRS technology for the quality control of fat and molasses. Samples of liquid molasses (n = 42) and liquid fat ( n = 61), provided by a feed manufacturer, were scanned in a FOSS-NIR Systems 6500 monochromator equipped with a spinning module. The samples were analysed by folded transmission, using a sample cup of 0.1mm pathlength and gold surface reflector. For molasses, calibration equations were developed for the prediction of moisture (SECV=1.69%; $r^2$=0, 42), gross protein (SECV=0, 14%; $r^2$=0, 99), ashy (SECV=0, 60%; $r^2$=0, 84), NaCl (SECV=0, 05%; $r^2$=0, 99) and sugars (SECV=1, 04%; $r^2$=0, 86). For animal fats calibrations were obtained for the prediction of moisture (SECV=0, 14%, $r^2$=0, 88), acidity index (SECV=0, 83%, $r^2$=0, 82), MIU (SECV=0, 38%, $r^2$=0, 94) and unsaponifiables (SECV=0, 45%, $r^2$=0, 87). High accuracy calibration equations were also obtained for the prediction of the fatty acid profile. The equations have $r^2$values around 0.9 or highest. The results showed that NIRS technology could provide rapid and accurate results and reduce analytical costs associated to the quality control of two Important feed ingredients of a well known chemical variability.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1253-1253
• /
• 2001

The ability to accurately assess wine quality is important during the wine making process, particularly when allocating batches of wines to styles determined by consumer requirements. Grape payments are often determined by the quality category of the wine that is produced from them. Wine quality, in terms of sensory characteristics, is normally a subjective measure, performed by experienced winemakers, wine competition judges or winetasting panellists. By nature, such assessments can be biased by individual preferences and may be subject to day-to-day variation. Taste and aroma compounds are often present in concentrations below the detection limit of near infrared (NIR) spectroscopy but the more abundant organic compounds offer potential for objective quality grading by this technique. Samples were drawn from one of Australia's major wine shows and from BRL Hardy's post-vintage wine quality allocation tastings. The samples were scanned in transmission mode with a FOSS NIR Systems 6500, over the wavelength range 400-2500 ㎚. Data analysis was performed with the Vision chemometrics package. With samples from the allocation tastings, the best correlations between NIR spectra and tasting data were obtained with dry red wines. These calibrations used loadings in the wavelengths related to anthocyanins, ethanol and possibly tannins. Anthocyanins are a group of compounds responsible for colour in red wines - restricting the wavelengths to those relating to anthocyanins produced calibrations of similar accuracy to those using the full wavelength range. This was particularly marked with Merlot, a variety that tends to have relatively lower anthocyanin levels than Cabernet Sauvignon and Shiraz. For dry white wines, calibrations appeared to be more dependent on ethanol characteristics of the spectrum, implying that quality correlated with fruit maturity. The correlations between NIR spectra and sensory data obtained using the wine show samples were less significant in general. This may be related to the fact that within most classes in the show, the samples may span vintages, glowing areas and winemaking styles, even though they may be made from only one grape variety. For dry red wines, the best calibrations were obtained with a class of Pinot Noir - a variety that tends to be produced in limited areas in Australia and would represent the least matrix variation. Good correlations were obtained with a tawny port class - these wines are sweet, fortified wines, that are aged for long periods in wooden barrels. During the ageing process Maillard browning compounds are formed and the water is lost through the barrels in preference to ethanol, producing “concentrated” darkly coloured wines with high alcohol content. These calibrations indicated heaviest loadings in the water regions of the spectrum, suggesting that “concentration” of the wines was important, whilst the visible and alcohol regions of the spectrum also featured as important factors. NIR calibrations based on sensory scores will always be difficult to obtain due to variation between individual winetasters. Nevertheless, these results warrant further investigation and may provide valuable Insight into the main parameters affecting wine quality.