• International Journal of Automotive Technology
• /
• v.4 no.3
• /
• pp.109-117
• /
• 2003

The analysis and evaluation of the transient performance by the transient response specifications under various acceleration speeds and types based on driver's typical acceleration habit are implemented by the experimental study to provide the appropriate direction for the transient control in a gasoline engine. The concept of the transient response specifications which consist of delay time, rising time, maximum overshoot and settling time, and the analysis method using them are introduced to evaluate the characteristics of the transient performance quantitatively. Furthermore four acceleration speeds and four acceleration types are set respectively to realize the various transient states which are similar to the real drive. Several performance parameters in terms of engine speed, manifold absolute pressure, fuel injection duration and air excess ratio are measured simultaneously during the various acceleration using a throttle actuator controlled by a PC. The transient response specifications characterized well the transient performance for the various acceleration speed and types quantitatively. Delay and rising time with increment of the acceleration speed became shorter, but settling time did longer. Intensified acceleration type appeared to be the most economical in view of fuel consumption, and linear acceleration type was found to have the least harmful emission concentration.

• Journal of KSNVE
• /
• v.6 no.4
• /
• pp.499-502
• /
• 1996

Interior noise, engine speed and vehicle speed are measured under transient road-load condition and interior noise signal is transformed by using the transient signal analysis methods, such as the spectrogram and wavelet transform. Using the analyzed results, subjective noise metrics such as the loudness, sharpness and articulation index at each vehicle speed can be estimated and characteristics of interior noise for various running modes can be discussed in the viewpoint of noise quality.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.10 no.4
• /
• pp.495-507
• /
• 1998

The transient characteristics of a 4.0㎾ inverter driven heat pump was investigated by theoretical and experimental studies. The heat pump used in this study consists of a high side scroll compressor and $\Phi$7 compact heat exchangers with two capillary tubes. A series of tests was peformed to examine the transient characteristics of heat pump in heating and cooling mode when the operating speed was varied from 30Hz to 102Hz. One of the major issues that has not been addressed so far is transient characteristics during speed modulation. A cycle simulation model has been developed to predict the cycle performance under frequency rise-up conditions, and the results of theoretical study were compared with the results of experimental study. The theoretical model was driven from mass conservation and energy conservation equations to predict the operation points of refrigerant cycle and the performances at various operating speeds. For transient conditions, the simulated results are in good agreement with the experimental results within 10%. The transient cycle migration of the liquid state refrigerant causes a significant dynamic change in system. Thus, the migration of refrigerant is the most important factor whenever An experimental analysis is performed or A simulation model is developed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.174-179
• /
• 2007

The transient brake time or distance is one of very important factors to guess the vehicle speed to inspect an automobile accident. But, it is usual that the vehicle speed is estimated by using only skid mark without considering the transient brake distance. Deceleration and the friction coefficients of tire and road surface play an important role in calculating the brake distance. In this paper, a scheme is presented to estimate more accurate automobile speed. The scheme contains the effect of the transient brake distance on the speed. Experiment was carried out on the asphalt, unpacked road to get relationships between the speeds and the skid mark distances, and to get the transient brake time. The experimental results were utilized to construct the equation to approximate more realistic vehicle speeds.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.1
• /
• pp.48-58
• /
• 2011

In this paper, an attempt has been made to design the current and speed proportional and integral (PI) regulators of self-commutating current source inverter-fed induction motor drive having capacitors at the machine end and to investigate the transient performance of the same for step changes in reference speed. The mathematical model of the complete drive system is developed in closed loop, and the characteristic equations of the systems are derived using perturbation about steady-state operating point in order to develop the characteristic equations. The D-partition technique is used for finding the stable region in the parametric plane. Frequency scanning technique is used to confirm the stability region. Final selection of the regulator parameters is done by comparing the transient response of the current and speed loops for step variations in reference. The performance of the drive is observed analytically through MATLAB simulation.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.8 no.1
• /
• pp.29-39
• /
• 2000

A series of tests were performed to verify the transient characteristics of heat pump in heating and cooling mode when operating speed was varied over the 30 to 102Hz. One of the major issues that has not been addressed so far is transient characteristics during speed modulation. The model for cycle simulation has been developed to predict the cycle performance under conditions of decreasing drive frequency and the results of the theoretical study were compared with the results of the experimental study. The simulated results were in good agreement with the experimental result within 10%. The transient cycle migration of the liquid state refrigerant causes significant dynamic change in system. Thus, the migration of refrigerant was the most important factor whenever do experimental results analysis or develop simulation model.

• International Journal of Highway Engineering
• /
• v.17 no.4
• /
• pp.33-40
• /
• 2015

PURPOSES: Evaluation of the wind speed effect on the temperature drop of an asphalt mixture during construction, by using the transient heat transfer theory and dominant convective heat transfer coefficient model. METHODS: Finite difference method (FDM) is used to solve the transient heat transfer difference equation numerically for various wind speeds and initial temperature conditions. The Blasius convective heat transfer coefficient model is adapted to account for the effect of wind speed in the temperature predictions of the asphalt mixture, and the Beaufort number is used to select a reasonable wind speed for the analysis. As a function of time and depth, the temperature of the pavement structure is predicted and analyzed for the given initial conditions. RESULTS : The effect of wind speed on the temperature drop of asphalt mixture is found to be significant. It seems that wind speed is another parameter to be accounted for in the construction specifications for obtaining a better quality of the asphalt mixture. CONCLUSIONS: It is concluded that wind speed has a significant effect on the temperature drop of the asphalt layer. Although additional field observations have to be made to reflect the effect of wind speed on the construction specifications, it appears that wind speed is a dominant variable to be considered, in addition to the atmospheric temperature.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.298-303
• /
• 1998

In the speed sensorless control of the induction motor, the machine parameters (especially the secondary resistance R2) have a strong influence to the speed estimation. It is known that the simultaneous estimation of the speed and R2 is impossible in the slip frequency type vector control, because the secondary flux is constant. But the secondary flux is not always constant in the speed transient state. In this paper the R2 estimation in the transient state without adding any additional signal to the stator current is proposed. This algorithm uses the least mean square algorithm and the adaptive algorithm, and it is possible to estimate the R2 exactly. This algorithm is verified by the digital simulations and the experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.694-699
• /
• 2005

This paper deals with a control technique of eliminating the transient vibration of a geared mechanical system. This technique is based on a model-based control with a rotational speed sensor in order to establish the damping effect at the driven machine part. A rotational speed sensor is installed in a driven gear, namely a bull gear. A control model is composed of a reduced-order mechanical part expressed as a transfer function between the rotational speed of the motor and that of the bull gear. This control model estimates a load speed after the rotational speed of the bull gear is acted on the transfer function. The difference between the estimated load speed and the motor speed is calculated dynamically and it is added to the velocity command to suppress the transient vibration generated at the load. This control technique is applied to a dies driving spindle of a form rolling machine. In this paper, the performance of this control method is examined by simulations. The settling time of the residual vibration generated at the loading inertia can be shortened down to about 1/2 of the uncompensated vibration level.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.3
• /
• pp.207-214
• /
• 2007

Theoretical analysis on transient torsional vibration was started from the early 1960s for high power synchronous motor application. Particularly. its simulation and measuring techniques in marine diesel engine field have been steadily studied by some classification societies and large marine diesel engine designers. This paper introduces the simulation method on transient torsional vibration of two stroke low speed diesel engine using the Newmark method.